MC3486DE4 - Quad RS-422/RS-423 Differential Line Receiver | Texas Instruments
MPN: MC3486DE4 ✓ ActiveMC3486DE4 Overview
A differential line receiver is a type of interface transceiver IC that recovers a logic signal from a balanced, differential transmission line such as RS-422 or RS-423. Its category hierarchy runs differential line receiver -> line receiver -> interface transceiver IC -> integrated circuit. Receivers are used where a sender is physically separated from the receiver by cable, where the signal has travelled through noisy industrial environments, or where several devices share one bus. Differential signalling rejects common-mode noise, and the 3-state output stage lets a controller share a single data bus between multiple receivers without bus contention.
The MC3486 offers four independent differential-input receivers in one package, with fast transition times and TTL-compatible outputs that drive standard CMOS/TTL logic directly. Because the outputs can be placed in a high-impedance state, the four channels can be muxed onto a shared data bus for multiplexing, bus arbitration, or test isolation. All four channels share common supply pins, so the device fits naturally into parallel, wide-bus architectures such as multi-drop data acquisition and instrumentation systems.
Internally, each channel consists of a differential input stage, a Schmitt-trigger style response that rejects slow-moving noise on the differential pair, and an output buffer with three drive states (high, low, high impedance). The differential threshold and common-mode range are set to suit balanced twisted-pair cabling rather than single-ended logic, which is why the device is specified against EIA/TIA-422-B and EIA/TIA-423-B instead of general-purpose logic levels.
Typical uses include industrial serial data acquisition, instrumentation and test equipment interfaces, computer-to-peripheral links, and control systems that must recover a differential signal over long cable runs. It is also commonly paired with a complementary quadruple differential line driver such as the MC3487 family, or with the MC1489/MC1488 families, to build complete balanced communication links.
When designing around the MC3486DE4, budget the enable pins and supply rails carefully: leaving an output enabled while another receiver drives the same bus node causes contention and excess current. Confirm the receiver's common-mode input range against the ground reference of the remote device, and place a termination network at the far end of the cable so the differential pair is referenced properly.
Drop-in alternatives for MC3486DE4 — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.
Variants in this series
Same-series models that are drop-in compatible with MC3486DE4 (same form factor and footprint) — differing in Package, Logic Compatibility, Number of Channels, Operating Temperature Range, Output Type.
MC3486D
✅ Drop-In ⚠️ Specs UnverifiedContact for price
View Datasheet →MC3486DR
✅ Drop-In ⚠️ Specs UnverifiedContact for price
View Datasheet →MC3486NSR
✅ Drop-In ⚠️ Specs UnverifiedContact for price
View Datasheet →MC3486DE4 Specifications
| Device Type | Quadruple differential line receiver with 3-state outputs |
| Number of Channels | 4 independent differential-input receivers |
| Output State | 3-state (high, low, high impedance) |
| Output Compatibility | TTL-compatible outputs |
| Supported Standards | ANSI TIA/EIA-422-B, ANSI TIA/EIA-423-B, ITU V.10, ITU V.11 |
| Package | 16-SOIC (SOP-16), 0.154 inch (3.90 mm) body width |
| Package Code / Shape | SOP, rectangular |
| Terminal Form | Gull wing |
| Mounting Type | Surface mount |
| Temperature Grade | Commercial |
| Transition Time | Fast transition times (per manufacturer datasheet) |
MC3486DE4 sop, rectangular Pin Configuration Guide
Pin configuration for MC3486DE4 (sop, rectangular package). Pin numbering, functions, and connection diagrams are defined in the manufacturer datasheet. Refer to it for the exact footprint and soldering guidelines.
No detailed pinout data available for MC3486DE4.
Refer to the datasheet for full pin configuration.
Typical Applications
MC3486DE4 is suitable for 6 applications: Industrial RS-422 Data Acquisition, Instrumentation and Test Equipment Interfaces, Computer-to-Peripheral Balanced Links, Multi-Drop Multiplexed Data Buses, Telecommunications and Remote Terminal Equipment, Process Control and PLC Remote I/O.
Industrial RS-422 Data Acquisition
The MC3486DE4 recovers four balanced differential signals simultaneously, which makes it a natural fit for multi-channel instrumentation that talks to remote sensors over RS-422 cabling. Each of the four channels has its own differential input pair and 3-state output, so a single 16-pin SOIC can serve an entire four-axis data-acquisition front end instead of four single-channel receivers. Because the device is specified to ANSI TIA/EIA-422-B, the recovered levels and common-mode tolerance match a transmitter built to the same standard. With fast transition times the received word rate stays high, while the TTL-compatible outputs drive the ADC front-end or microcontroller inputs directly without level translation.
Recommended
Instrumentation and Test Equipment Interfaces
In lab and production test systems, the MC3486DE4 provides the receive side of a multi-drop instrument bus where one controller polls several instruments on shared cabling. The 3-state outputs are the decisive feature: only the selected receiver is enabled at a time, so several devices can share the same data lines without contention. Four channels per package means a 16-bit instrument bus needs only two receiver chips plus enable decoding logic. Because the device meets TIA/EIA-422-B and TIA/EIA-423-B, it can be deployed in systems whose specification references either RS-422 or RS-423 cabling rules, keeping termination and biasing unchanged between them.
Recommended
Computer-to-Peripheral Balanced Links
The MC3486DE4 is used on the receive side of balanced interconnects between a host controller and remote peripherals over longer cable runs than single-ended logic allows. Differential reception rejects common-mode noise picked up along the way, so data stays clean in industrial and laboratory environments where ground offsets exist between devices. Four independent receivers in one 16-SOIC package conserve board area compared with discrete single-channel parts, and the TTL-compatible outputs mean the recovered signals can enter a microcontroller or host bus interface directly. Where a complete link is needed, pairing with a quad differential driver such as the MC3487 family keeps the driver and receiver electrically consistent from both ends of the cable.
Recommended
Multi-Drop Multiplexed Data Buses
The per-channel high-impedance outputs of the MC3486DE4 enable classic multiplexing schemes in which several remote nodes drive one shared data bus under arbiter control. Each receiver channel can be disabled while the bus is owned by another node, so the shared conductors see only one driver at a time and contention stays predictable. This pattern appears in legacy parallel-bus and remote I/O architectures, in older CNC and telemetry equipment, and in retrofit designs that add a modern microcontroller to an existing TIA/EIA-422-B cabling infrastructure. The commercial 16-SOIC package also means the part can be placed by standard pick-and-place lines during repairs and line upgrades without special assembly steps.
Recommended
Telecommunications and Remote Terminal Equipment
The MC3486DE4 suits line-card and terminal equipment that terminates balanced subscriber or backhaul-style differential lines and converts them to logic levels for a processor. Four channels per package suits line cards that carry several signalling paths, and the 3-state outputs allow outputs to be parked safely during firmware reconfiguration or line re-seating. Because the receiver is referenced to TIA/EIA-423-B as well as TIA/EIA-422-B, systems that mix RS-423 host ports with RS-422 links can use one receiver type, which simplifies qualification and spare-parts stocking. Commercial temperature grading keeps the part in instrument and indoor terminal environments rather than harsh outdoor enclosures.
Recommended
Process Control and PLC Remote I/O
In a process-control installation, sensor and actuator nodes are often linked back to a controller over shielded twisted-pair runs that pass next to motors and switching gear. The MC3486DE4 provides the receive path on the controller side of that link, converting the balanced differential waveform into clean logic for the PLC or remote I/O module. Because the device is a quad receiver, a single module can terminate four differential I/O points at once, keeping the terminal-block wiring uniform. The high-impedance outputs also let a controller monitor several buses in rotation, and the standard 16-SOIC footprint means the same board layout supports the commercial-temperature ordering code used in indoor control cabinets.
Recommended
Recommended Products Summary
Engineering reference data for MC3486DE4 — comparison, design guidance, and compliance information.
Selection Guide
Comparison with Alternatives
| Parameter | This Product | MC3486D | MC3486DR | MC3486NSR |
|---|---|---|---|---|
| Package | 16-SOIC (SOP-16), 0.154 inch (3.90 mm) width | 16-SOIC (SOP-16) - same footprint | 16-SOIC (SOP-16) - same footprint | 16-SOIC (SOP-16) - same footprint |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Function | Quadruple differential line receiver with 3-state outputs | Quadruple differential line receiver with 3-state outputs | Quadruple differential line receiver with 3-state outputs | Quadruple differential line receiver with 3-state outputs |
| Number of Channels | 4 | 4 | 4 | 4 |
| Supported Standards | ANSI TIA/EIA-422-B, ANSI TIA/EIA-423-B, ITU V.10, ITU V.11 | ANSI TIA/EIA-422-B, ANSI TIA/EIA-423-B, ITU V.10, ITU V.11 | ANSI TIA/EIA-422-B, ANSI TIA/EIA-423-B, ITU V.10, ITU V.11 | ANSI TIA/EIA-422-B, ANSI TIA/EIA-423-B, ITU V.10, ITU V.11 |
| Output Type | 3-state, TTL-compatible | 3-state, TTL-compatible | 3-state, TTL-compatible | 3-state, TTL-compatible |
| Transition Time | Fast transition times per manufacturer data sheet | Fast transition times per manufacturer data sheet | Fast transition times per manufacturer data sheet | Fast transition times per manufacturer data sheet |
| Mounting Type | Surface mount, gull-wing terminals | Surface mount, gull-wing terminals | Surface mount, gull-wing terminals | Surface mount, gull-wing terminals |
Key Differentiators
- Four independent differential receivers in one 16-pin SOIC (vs MC1489NE4)
- Per-channel high-impedance outputs enable shared-bus multiplexing (vs MC3486DR)
- Specified to both TIA/EIA-422-B and TIA/EIA-423-B (vs MC3487DE4)
Design Notes
The 3-state outputs are the part's most useful feature and its most common failure point. If a channel output is left enabled while another node drives the same bus node, the two drivers fight and the supply current spikes, which can overheat the device or damage a remote driver. Always drive the enable control from a defined state at power-up, and include a pull-down or pull-up so the output is parked during reset and brown-out. Confirm the enable polarity and pin numbers against the pin-configuration table in the manufacturer data sheet, since the enable arrangement differs between receiver and driver families.
Place the SOIC-16 receiver close to the connector or transceiver boundary so the unbalanced stub between the cable and the differential inputs stays short. Keep the differential pair routed as a coupled pair with a continuous ground plane beneath it; unmatched pair lengths degrade the common-mode rejection that makes RS-422 robust. Provide an unobstructed ground return path for the cable shield and connect the shield to the chassis or single reference point near the entry, otherwise common-mode energy can be injected into the input stage.
The receiver's supply rails must be referenced to the same ground as the remote transmitter for the differential threshold to remain meaningful. Decouple each supply pin locally with a high-frequency ceramic capacitor plus a bulk electrolytic placed within a few millimetres of the pins, and route the supply to the device as a separate trace from the noisy differential inputs. Because four channels share the same supply pins, a transient on one channel can momentarily disturb the reference of the other three, so clean local decoupling directly improves margin on all four channels.
Termination and biasing belong to the system design, not to the receiver IC. For RS-422 links, place the termination at the far end of the cable so that reflections are absorbed at the end opposite the source; for RS-423, follow the TIA/EIA-423-B configuration that includes the biasing network so the idle differential voltage is defined. Do not terminate at both ends of a long run unless the system specification calls for it, because double termination over-damps the signal and can degrade transition times at higher data rates.
Compliance Information
No RoHS, REACH, lead-free or conflict-minerals declaration was stated in the product listings reviewed. The part is a commercial-grade interface receiver rather than an automotive-qualified device, so AEC-Q100 does not apply.