PCA9665N - 1MHz FM+ Parallel-to-I2C Controller | NXP
MPN: PCA9665N ✓ ActivePCA9665N Overview
An I2C controller is an interface IC that bridges parallel processor buses and the serial I2C ecosystem. Parallel buses transfer multiple bits simultaneously, while I2C uses clocked SDA and SCL lines to exchange data between integrated circuits. The PCA9665N places this conversion in a dedicated peripheral, reducing the number of serial transactions and GPIO connections required by a host processor when it must control multiple I2C devices.
The PCA9665N supports I2C Fast-mode Plus operation at 1 MHz and can drive SCL and SDA lines with 25 mA capability. Its 68-byte buffer supports byte-oriented and buffered data transfers between the parallel and serial sides. General Call support and software reset over the parallel bus add useful control functions for systems that need coordinated peripheral addressing or restart behavior.
Two operating modes make the controller suitable for different system architectures. In master mode, it initiates transfers on the I2C bus; in slave mode, it responds to another bus controller. Communication can be interrupt-driven or managed through a polled handshake, allowing the interface to fit both event-driven firmware and simpler supervisory control loops.
Typical applications include industrial control equipment, test and measurement systems, communication modules, peripheral expansion, legacy parallel-processor systems, and embedded products that need to retain a parallel bus while adding modern serial peripherals. Its through-hole DIP format is particularly useful for prototypes, legacy control boards, and industrial systems assembled around through-hole components.
Designers should account for the 1 MHz bus limit, confirm that every connected I2C device supports the intended speed, and validate pull-up resistor sizing for the target bus voltage and capacitance. Because Fast-mode Plus uses lower resistance pull-ups than standard Fast-mode, incorrect resistor values can produce excessive rise times, ringing, or communication errors.
This page organizes the manufacturer-described controller capabilities, package information, sourcing pathways, and engineering trade-offs into a concise selection guide. It also distinguishes the DIP-20 target from similarly named PCA9665 devices offered in SOIC, TSSOP, and HVQFN packages, which cannot replace this through-hole part without a PCB redesign.
Drop-in alternatives for PCA9665N — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.
PCA9665N,112
✅ Drop-In📋 Reference alternative (not in catalog)
PCA9665N Specifications
| Device Type | Fast-mode Plus parallel-bus to I2C-bus controller |
| I2C Bus Maximum Data Rate | 1 MHz |
| I2C Drive Capability | 25 mA on SCL and SDA |
| Data Buffer Size | 68 byte |
| Supply Voltage | 2.5 V or 3.3 V |
| I2C Operating Role | Master or slave |
| Transfer Organization | Byte or buffered basis |
| Host Interface | 8-bit parallel bus |
| Transfer Control | Interrupt or polled handshake |
| General Call Support | Yes |
| Software Reset Support | Yes, over the parallel bus |
| Package Type | 20-pin DIP |
| Mounting Type | Through-hole |
| Temperature Grade | Industrial |
| Application Segment | Industrial |
| Number of Pins | 20 |
PCA9665N 20-pin dip Pin Configuration Guide
Pin configuration for PCA9665N (20-pin dip package). Pin numbering, functions, and connection diagrams are defined in the manufacturer datasheet. Refer to it for the exact footprint and soldering guidelines.
No detailed pinout data available for PCA9665N.
Refer to the datasheet for full pin configuration.
Typical Applications
PCA9665N is suitable for 6 applications: Industrial Parallel-Control Expansion, Test and Measurement Equipment, Communication and Network Peripherals, Legacy Microprocessor I2C Upgrade, Embedded Peripheral Expansion, Prototype and Legacy Through-Hole Assemblies.
Industrial Parallel-Control Expansion
The PCA9665N fits legacy industrial controllers whose host processor exposes an 8-bit parallel bus but needs to operate several I2C peripherals. It acts as a dedicated protocol bridge, supporting master or slave operation at up to 1 MHz with interrupt-driven or polled-handshake transfers. The 68-byte buffer helps separate parallel-bus activity from serial-bus timing, while 25 mA SCL and SDA drive capability supports industrial interconnect arrangements. Designers should confirm logic-level compatibility, choose pull-ups for the intended bus capacitance, and test all connected peripherals at the highest intended operating frequency.
Test and Measurement Equipment
The PCA9665N is useful in test and measurement instruments where a legacy parallel control processor must read sensors or configure data-acquisition components over I2C. Its buffered 68-byte transfer path reduces the need for direct serial-driver routines in the host firmware, while selectable interrupt or polled-handshake operation supports both fast event capture and simple supervisory loops. Fast-mode Plus operation up to 1 MHz can shorten transaction time when the attached instruments support that rate. Validation should include bus timing, clock stretching behavior, interrupt latency, and recovery after reset or power-up.
Communication and Network Peripherals
The PCA9665N can bridge a parallel system processor to I2C communication devices such as transceivers, EEPROMs, or sensor controllers. Operating as an I2C master allows the host to initiate standardized serial transactions, while slave mode supports configurations in which another bus master addresses the parallel-side system. The 1 MHz Fast-mode Plus capability is attractive for communication-oriented industrial designs, provided every attached device supports the same rate. The interrupt interface lets the parallel processor remain responsive while the controller completes byte or buffered transfers.
Legacy Microprocessor I2C Upgrade
The PCA9665N offers a practical path for adding I2C to a microprocessor or microcontroller platform that exposes a parallel bus rather than dedicated I2C pins. Instead of emulating serial timing in software with multiple GPIO lines, the controller manages the I2C protocol and can buffer data for transfer to the host. This architecture suits established industrial platforms being updated with modern sensors or memories. Software designers should map the host handshake and interrupt behavior, verify reset semantics, and check whether existing address assignments conflict with newly attached I2C devices.
Embedded Peripheral Expansion
The PCA9665N is applicable to embedded systems that need multiple serial peripherals while retaining a parallel-bus controller. General Call support can help coordinate devices that recognize the reserved general-call address, and software reset over the parallel bus provides a host-controlled recovery mechanism. The 68-byte buffer accommodates burst-oriented transfers, and the ability to choose interrupt-driven or polled operation lets firmware balance latency against processor utilization. System validation should cover address conflicts, bus recovery after a slave holds SDA low, and the effect of pull-up resistance on signal rise time.
Prototype and Legacy Through-Hole Assemblies
The 20-pin DIP package makes the PCA9665N convenient for prototypes, educational platforms, and industrial boards assembled with through-hole components. It allows an engineer to prototype a parallel-to-I2C interface on a perforated board before committing to a compact surface-mount PCB. The industrial-grade designation and 2.5 V or 3.3 V operation make it relevant to controlled laboratory and factory equipment, but designers should still verify the exact temperature range and supply-current limits. Breadboard prototyping also requires careful decoupling and short I2C routing.
Engineering reference data for PCA9665N — comparison, design guidance, and compliance information.
Selection Guide
Comparison with Alternatives
| Parameter | This Product |
|---|---|
| Package | 20-pin DIP |
| Brand | NXP Semiconductors |
| Product Type | Fast-mode Plus parallel-bus to I2C-bus controller |
| Maximum I2C Data Rate | 1 MHz |
| SCL/SDA Drive Capability | 25 mA |
| Data Buffer Size | 68 byte |
| Supply Voltage | 2.5 V or 3.3 V |
| I2C Operating Role | Master or slave |
| Transfer Control | Interrupt or polled handshake |
| Mounting Type | Through-hole |
Key Differentiators
- Dedicated high-speed parallel-to-I2C conversion (vs PCA9665D,118)
- Through-hole integration for legacy and industrial boards (vs PCA9665BS,118)
- Family interface performance (vs PCA9665PW)
Design Notes
Calculate the I2C pull-up resistance from the bus voltage, total capacitance, leakage current, and the required rise-time budget rather than selecting a common value by default. The PCA9665N supports operation up to 1 MHz, where excessive pull-up resistance can slow SCL or SDA rising edges and create communication errors. Keep SCL and SDA traces short, route them away from switching nodes, and inspect rise time, ringing, and timing margin on the assembled board with a suitable oscilloscope.
Treat the PCA9665N as a DIP-20 component and preserve the manufacturer package drawing when laying out the PCB. Place its decoupling capacitors close to the supply and ground pins, with the shortest practical return path to the supply reference. Because the device bridges a wide parallel bus with a high-speed serial bus, separate sensitive serial routing from noisy parallel-bus outputs where possible. Confirm logic-level compatibility of the parallel host before applying 2.5 V or 3.3 V signals.
Do not substitute PCA9665BS, PCA9665D, or PCA9665PW by MPN similarity alone. These ordering options use different packages and therefore require different PCB land patterns. Also avoid assuming every I2C peripheral can operate at 1 MHz: Fast-mode Plus support must be confirmed for each device. Finally, review General Call address use and the parallel-bus software reset behavior so that an initialization command cannot inadvertently address or reset an unintended peripheral.
Compliance Information
The manufacturer product page identifies industrial use but does not state RoHS, REACH, lead-free, halogen-free, or conflict-minerals status. AEC-Q100 qualification is not applicable to the stated industrial classification because automotive qualification was not identified.