SI3200-G-FS - 100V Dual-Channel SLIC Interface IC | Skyworks Solutions
MPN: SI3200-G-FS ✓ ActiveSI3200-G-FS Overview
A Subscriber Line Interface Concept, or SLIC, is an interface IC that sits between a telephone line and the digital voice-processing portion of a communications system. It handles linefeed-related functions and supports analog voice-channel connectivity in access equipment. In the power hierarchy, the SI3200-G-FS belongs to the semiconductor class, then to integrated circuits, then to interface ICs, with the narrower application category of telecom linefeed interfaces.
The SI3200-G-FS is identified as a 2-channel SLIC and is rated for 100 V linefeed operation. The documented 3.3 V supply and 45 mA operating-current figure make it suitable for low-voltage telecom equipment designs in which the line interface must operate from a protected or isolated supply architecture. Its 63 dB specification is a key channel-performance figure for evaluating signal-chain behavior, although the complete system noise and distortion budget also depends on the external linefeed network, protection devices, and the voice codec.
The available package information is not fully consistent across listings. DigiKey describes the related SI3200-G-FSR as a 16-SOIC, while the SI3200-G-FS search result describes a 6-pin SMD arrangement. Because the exact pin assignments for the target package are not published in the manufacturer material included here, the pinout is left unset and the package diagram should be confirmed against the final device drawing before PCB layout.
Typical applications include two-channel voice access, telephone line interface cards, subscriber line access concentrators, and telecom equipment using a dual-chipset SLIC architecture. The 100 V linefeed rating is particularly relevant to designs where the interface must withstand the voltage environment associated with analog telephone lines.
For a new layout, begin with the manufacturer datasheet pin description and the linefeed reference circuit. Confirm the package drawing, exposed or lead configuration, protection network, supply sequencing, and decoupling requirements before committing copper. This page consolidates the verified electrical highlights, sourcing information, package cautions, and practical design guidance for engineers evaluating the SI3200-G-FS.
Drop-in alternatives for SI3200-G-FS — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.
Variants in this series
Same-series models that are drop-in compatible with SI3200-G-FS (same form factor and footprint) — differing in Lead-Free Status, Package, Product Type, Supply Voltage.
SI3200-G-FSR
✅ Drop-In📋 Reference alternative (not in catalog)
SI3200-FS
✅ Drop-InContact for price
View Datasheet →SI3200-G-FS Specifications
| Product Type | Subscriber Line Interface Concept (SLIC) IC |
| Channel Count | 2 channels |
| Linefeed Voltage Rating | 100 V |
| Operating Current | 45 mA |
| Supply Voltage | 3.3 V |
| Channel Performance | 63 dB |
| Device Category | Telecom Interface IC |
| Function | Dual-channel linefeed interface |
| Linefeed Type | Subscriber Line Interface Concept (SLIC) |
| Package | 6-pin SMD package |
| Related Listed Package | 16-SOIC for SI3200-G-FSR |
| Lead-Free Status | Lead-free device |
| Dual-Channel Architecture | Two units required for a dual-channel chipset |
| Mounting Type | Surface mount |
SI3200-G-FS 16-soic for si3200-g-fsr Pin Configuration Guide
Pin configuration for SI3200-G-FS (16-soic for si3200-g-fsr package). Pin numbering, functions, and connection diagrams are defined in the manufacturer datasheet. Refer to it for the exact footprint and soldering guidelines.
No detailed pinout data available for SI3200-G-FS.
Refer to the datasheet for full pin configuration.
Typical Applications
SI3200-G-FS is suitable for 6 applications: Two-Channel Telephone Line Interface, Subscriber Line Access Concentrator, Voice Gateway Line Card, Central Office Voice Access, Digital Private Exchange Interface, Remote Terminal Voice Module.
Two-Channel Telephone Line Interface
The SI3200-G-FS fits a two-channel subscriber-line access circuit because it is identified as a 2-channel SLIC with a 100 V linefeed rating and 63 dB channel-performance figure. It can sit between protected analog linefeed circuitry and the digital voice-processing section of a line card. The documented 3.3 V operation and approximately 45 mA current support integration into low-voltage telecom logic. Before layout, verify the exact 6-pin SMD outline and confirm that the selected linefeed network and protection components match the manufacturer reference circuit.
Recommended
Subscriber Line Access Concentrator
A subscriber-line access concentrator can use the SI3200-G-FS where two analog voice channels must be handled by one telecom interface IC. Its dual-channel organization reduces the number of linefeed devices compared with a single-channel implementation, while the 100 V linefeed rating addresses the high-voltage telephone-line environment. The 45 mA operating-current figure is useful for rail planning on the 3.3 V domain. System-level ringing, surge protection, and codec interoperability must still be validated against the manufacturer application design.
Recommended
Voice Gateway Line Card
The SI3200-G-FS is applicable to a voice gateway line card that bridges analog subscriber lines with packet-processing electronics. Its 2-channel SLIC architecture supports parallel voice paths, while the 63 dB specification provides a defined channel-performance figure for front-end selection. The interface operates from 3.3 V, making it suitable for boards that already distribute a low-voltage digital rail. The 100 V linefeed requirement should be handled with an approved protection network and adequate copper clearance rather than treated as an ordinary 3.3 V logic connection.
Recommended
Central Office Voice Access
Central-office voice access equipment can use the SI3200-G-FS when the design requires a dedicated dual-channel linefeed front end. The 100 V rating is relevant to subscriber-line circuits, and the 3.3 V supply allows the interface to operate near modern voice processors and digital switching logic. Two-device chipset configurations may also use this family, depending on the channel arrangement required by the surrounding codec architecture. Confirm device-to-device timing, linefeed impedance, and protection strategy with the manufacturer reference schematic.
Recommended
Digital Private Exchange Interface
The SI3200-G-FS can support analog trunk or line-facing sections of a digital private exchange when two voice channels are needed on a compact board. Its dual-channel organization and 100 V linefeed rating are useful in equipment exposed to telephone-line voltages, while 3.3 V operation simplifies connection to digital control and voice-processing circuits. Because this is a linefeed interface rather than a complete codec, the design must also provide the required line network, protection, and signal conversion. Validate channel gain and 63 dB performance within the complete voice path.
Recommended
Remote Terminal Voice Module
A remote terminal voice module can use the SI3200-G-FS for compact two-channel line termination where a 3.3 V digital rail is available. The approximately 45 mA operating-current figure helps establish the local supply budget, and the 100 V linefeed interface separates the voice module from the low-voltage control electronics. Care is required at the board boundary because the linefeed protection network, isolation strategy, and creepage distance are part of the complete design. Use the manufacturer application circuit to determine component placement around the device.
Recommended
Recommended Products Summary
Engineering reference data for SI3200-G-FS — comparison, design guidance, and compliance information.
Selection Guide
Comparison with Alternatives
| Parameter | This Product | SI3200-G-FSR | SI3200-FS |
|---|---|---|---|
| Brand | Skyworks Solutions | Skyworks Solutions | Skyworks Solutions |
| Primary Function | 2-channel SLIC linefeed interface | Telecom SLIC and CODEC | Subscriber Line Interface Circuit |
| Device Category | Telecom Interface IC | Telecom IC | Telecom Interface IC |
Key Differentiators
- Documented dual-channel linefeed organization (vs SI3200-G-FSR)
- Defined 3.3 V operating point (vs SI3200-FS)
- Published operating-current figure (vs SI3200-G-FSR)
Design Notes
Resolve the package discrepancy before layout. The SI3200-G-FS result identifies a 6-pin SMD package, while the related SI3200-G-FSR is identified as a 16-SOIC. Do not derive land patterns from the related part. Use the manufacturer SI3200-G-FS package drawing, pin table, and solder mask recommendations to establish pad locations and keep the high-voltage linefeed network outside low-voltage signal-clearance areas.
Separate the 3.3 V supply budget from the 100 V linefeed domain. The documented operating current is approximately 45 mA, so the device supply must maintain 3.3 V under the required channel and system load. Follow the manufacturer reference circuit for decoupling and protection components. Do not assume that the 100 V rating permits 100 V on the 3.3 V rail or on any unspecified package pin.
Do not treat a similar SI3200 family member as an automatic substitute. SI3200-G-FSR is listed as a 16-SOIC SLIC/CODEC, and SI3200-FS has a different listed maximum-supply figure. Before replacement, compare every pin, supply domain, linefeed topology, protection method, and codec interface. A package-name match alone is insufficient evidence for a production drop-in.
Place the linefeed protection and ringing-control network close to the interface pins while maintaining the separation required by the final 100 V design class. Keep the 63 dB channel-performance path away from noisy switching inductors and digital return currents. Use the manufacturer's application layout as the baseline, then review creepage, clearance, grounding, and copper-current capacity with the board fabrication rules.
Compliance Information
The Mouser listing identifies the SI3200-G-FS as a lead-free device. Explicit RoHS, REACH, halogen-free, conflict-minerals, and AEC-Q100 declarations were not included.