VSC7448YIH-01 - 52-Port 80G Ethernet Switch | Microchip
MPN: VSC7448YIH-01 ✓ ActiveVSC7448YIH-01 Overview
An Ethernet switch is a network-semiconductor device that receives frames on multiple physical interfaces and forwards them between ports using Layer 2 addresses. A Layer 3 switch additionally performs routing functions, while a stackable switch supports coordinated operation across multiple devices. The VSC7448 belongs to Microchip's SparX-IV-80 family, combining high-density port configurations with 10G uplink capability in one integrated device.
The headline features of VSC7448YIH-01 include an 80G switching fabric, support for up to 52 Ethernet ports, and mixed 1G, 2.5G, and 10G port configurations. The 672-FCBGA package provides the dense physical interface required for a high-port-count switching ASIC. A distributor listing also identifies the part as a 52-port L2/L3 stackable Gigabit Ethernet switch with 10 Gbps links.
This device targets networking equipment that needs high aggregation capacity without distributing traffic across many external switching components. Its port mix can serve copper or fiber-facing access interfaces through suitable external PHYs, while 10G links support higher-bandwidth aggregation. Enterprise switching features, combined with Layer 3 operation, allow the device to serve in access, distribution, and selected core-adjacent designs rather than only simple unmanaged bridging.
Typical uses include industrial Ethernet switches, telecom access equipment, enterprise campus-edge systems, network appliances, and stacked LAN configurations. In these systems, the device can consolidate many lower-speed ports and provide high-speed uplinks. Designers should account for the large BGA thermal and routing requirements, validate the specific port map and protocol stack, and complete high-speed signal-integrity and power-integrity validation on the final board.
The most important design consideration is that a 672-ball BGA requires careful escape routing, multilayer PCB construction, controlled-reference-plane geometry, and adequate thermal design. The 27 x 27 mm package also makes system mechanical constraints significant. Use the manufacturer's evaluation guidance and device documentation when defining layer stack-up, power delivery, clocking, SerDes implementation, and connector or PHY placement.
This page consolidates the device's port and package characteristics with application guidance, comparison details, and actionable PCB considerations. It is intended to help networking engineers establish whether the VSC7448YIH-01 fits a specific 1G, 2.5G, or 10G industrial Ethernet architecture before beginning high-density BGA implementation.
Drop-in alternatives for VSC7448YIH-01 — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.
VSC7448YIH-02
✅ Drop-In📋 Reference alternative (not in catalog)
VSC7448YIH-01 Maximum Ratings & Electrical Characteristics
| Device Type | L2/L3 stackable Ethernet switch |
| Product Series | SparX-IV-80 |
| Maximum Switching Capacity | 80 Gbps |
| Maximum Port Count | 52 ports |
| Supported Ethernet Speeds | 1G, 2.5G, and 10G Ethernet |
| Maximum Uplink Speed | 10 Gbps |
| Layer 2 Support | Supported |
| Layer 3 Support | Supported |
| Stacking Support | Supported |
| Package | 672-FCBGA, 27 x 27 mm |
| Ball Count | 672 balls |
| Packaging | Tray |
| Operating Temperature | -40 °C to 110 °C |
| Interface | PCI |
VSC7448YIH-01 672-fcbga, 27 x 27 mm Pin Configuration Guide
Pin configuration for VSC7448YIH-01 (672-fcbga, 27 x 27 mm package). Pin numbering, functions, and connection diagrams are defined in the manufacturer datasheet. Refer to it for the exact footprint and soldering guidelines.
No detailed pinout data available for VSC7448YIH-01.
Refer to the datasheet for full pin configuration.
Typical Applications
VSC7448YIH-01 is suitable for 6 applications: Industrial Ethernet Access Switch, Telecom Access and Aggregation, Enterprise Stackable LAN Switch, Network Appliance with Mixed-Speed Ports, Industrial Control and Automation Gateway, Data Center Top-of-Rack Platform.
Industrial Ethernet Access Switch
The VSC7448YIH-01 fits high-density industrial Ethernet access equipment because it combines up to 52 ports with an 80 Gbps switching fabric. A product can map lower-speed access interfaces across the switching array while retaining 10G links for equipment-to-equipment aggregation. Its stated -40 °C to 110 °C range also supports harsh industrial environments. The device is implemented as a central switching ASIC, with suitable external PHYs handling physical-layer connectivity and the board providing power delivery, clocking, and high-speed escape routing. The principal engineering trade-off is PCB complexity: a 672-FCBGA requires a dense multilayer design, careful SerDes signal integrity, and a thermal strategy suitable for sustained traffic across many ports.
Recommended
Telecom Access and Aggregation
The VSC7448YIH-01 is suitable for telecom access and aggregation systems requiring dense Ethernet port concentration and high-speed uplinks. Its support for a combination of 1G, 2.5G, and 10G links allows service equipment to connect multiple subscriber or service-facing interfaces to a shared 80G switching fabric. Layer 3 switching features can support managed routing at the edge of the network, while stacking enables expansion across multiple chassis. The main implementation challenge is signal and power integrity around the 672-ball BGA. Designers should establish a multilayer stack-up, use continuous reference planes where appropriate, control high-speed differential impedance, and provide independent power filtering close to the device.
Recommended
Enterprise Stackable LAN Switch
The VSC7448YIH-01 can serve as the switching core of an enterprise stackable LAN product because it combines L2 and L3 forwarding with as many as 52 ports. The 80G fabric provides aggregation capacity for many 1G access ports, while 2.5G and 10G options accommodate server-facing and backbone connections. Stacking support allows multiple switching units to operate as a coordinated system, reducing the need for separate routing devices in selected topologies. For a compact enterprise platform, the 672-FCBGA footprint demands careful escape-routing density and substantial thermal copper. The system should also include hardware support for management, synchronization, and failover according to the manufacturer's device and software documentation.
Recommended
Network Appliance with Mixed-Speed Ports
The VSC7448YIH-01 supports network appliances that need flexible combinations of 1G, 2.5G, and 10G connectivity rather than a uniform port arrangement. Up to 52 ports provide high density, while the 80G switching fabric can support simultaneous traffic across access and aggregation links. This makes the device relevant to industrial gateways, edge appliances, and secure network products that must bridge legacy 1G devices while adding 2.5G or 10G backhaul. Design work should begin with a precise port-allocation matrix and validated SerDes lane configuration. PCB complexity is substantial because the 27 x 27 mm 672-FCBGA demands dense escape routing, strict impedance control, and power planes capable of handling dynamic switching loads.
Recommended
Industrial Control and Automation Gateway
The VSC7448YIH-01 can anchor an industrial control or automation gateway that combines numerous machine-facing Ethernet links with higher-speed plant or backhaul connections. Its 1G options suit standard industrial Ethernet, while 2.5G and 10G links support data aggregation, vision, and line-side uplinks. The stated -40 °C to 110 °C operating range aligns with many demanding industrial environments. As a central L2/L3 switching element, it reduces the number of discrete switching blocks needed in the gateway. Thermal and reliability work should account for continuous traffic, enclosure temperature rise, and the BGA's solder-joint requirements. For functional safety projects, verify AEC-Q100 status separately because that qualification is not established by the available product information.
Recommended
Data Center Top-of-Rack Platform
The VSC7448YIH-01 can be evaluated for a data-center top-of-rack platform requiring many access ports and high-speed server-facing links. Up to 52 ports provide physical density, while 10G connectivity supports server aggregation and 80G switching capacity can serve multiple traffic classes. Layer 3 switching and stacking make it possible to consolidate edge switching functions in a compact system. The principal limitation is implementation rather than headline port count: a 672-FCBGA in a 27 x 27 mm package requires sophisticated multilayer PCB engineering, high-speed clock and SerDes validation, and careful thermal design. Before adoption, verify which of the mixed-speed configurations, management features, and stacking profiles are enabled in the exact ordering code and firmware release.
Recommended
Recommended Products Summary
Engineering reference data for VSC7448YIH-01 — comparison, design guidance, and compliance information.
Selection Guide
Comparison with Alternatives
| Parameter | This Product | VSC7448YIH-02 |
|---|---|---|
| Brand | Microchip Technology | Microchip Technology |
| Package | 672-FCBGA (27 x 27 mm) | 672-FCBGA (27 x 27 mm) |
| Device Type | L2/L3 stackable Ethernet switch | Telecom IC Ethernet switch |
| Product Family | SparX-IV-80 | VSC7448 family |
Key Differentiators
- High switching capacity in a single dense port device (vs VSC7448YIH-02)
- Mixed 1G, 2.5G, and 10G port support (vs VSC7448YIH-02)
- Defined industrial temperature range (vs VSC7448YIH-02)
Design Notes
Plan the PCB as a high-density multilayer design around the 672-FCBGA. Establish a stack-up that supports short BGA escape routing, continuous reference planes, controlled differential impedance, and adequate power-plane distribution. Follow the manufacturer's pad, via, and land-pattern guidance exactly; do not derive a 672-ball footprint from a generic BGA library. Validate every escape segment with the final stack-up and manufacturing rules.
Route all 10G and 2.5G SerDes links as controlled-impedance differential pairs with continuous reference planes and minimal stubs. Validate insertion loss, return loss, crosstalk, jitter, and lane-to-lane skew against the device requirements. Pay particular attention to connector or PHY escapes from the BGA because their transitions can dominate channel performance even when the internal traces are short.
Use a dedicated, low-impedance power-distribution architecture for the switching ASIC and isolate each supply domain with appropriate filtering close to the device. Place bulk and high-frequency decoupling according to the manufacturer power-distribution guidance, then check voltage droop under maximum port activity. Thermal and power simulations should use realistic traffic profiles because simultaneous line-rate activity can create a substantially different load than an idle bench test.
Treat the 27 x 27 mm BGA as a major heat source and provide copper spreading beneath and around the package while maintaining required electrical clearances. Base thermal conclusions on the actual enclosure, airflow, substrate, and adjacent heat sources. Validate junction-temperature margins at the maximum -40 °C to 110 °C ambient boundary, and verify solder-joint reliability through appropriate assembly and thermal-cycling procedures.
Do not assume that two devices with the same 672-FCBGA outline are functionally drop-in replacements. Confirm the exact ordering code, device revision, port map, supported clocking, boot configuration, firmware, and qualification requirements. In particular, validate VSC7448YIH-01 versus VSC7448YIH-02 against the manufacturer documentation before using the -02 part in an approved VSC7448YIH-01 design.
Compliance Information
The available product and distributor information does not state RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status for the exact VSC7448YIH-01 ordering code. Verify these requirements with Microchip before production release.