VSC8494YJE-12 - Dual/Quad 10GE PHY | Microchip Technology
MPN: VSC8494YJE-12 ✗ End of LifeVSC8494YJE-12 Overview
A 10GE PHY is an Ethernet physical-layer transceiver that converts parallel digital data into high-speed serial signaling for network transmission and converts incoming serial signals back into digital data. The VSC8494YJE-12 combines dual/quad 10GbE capability with OTN-FEC functionality, making it suitable for equipment that requires Ethernet throughput and forward-error-correction capability in the same high-density package. The 780-FCBGA construction supports complex, high-pin-count telecom designs while requiring careful PCB layout and thermal management.
The verified product information identifies the VSC8494YJE-12 as an Ethernet switch device and as a dual/quad 10GE PHY with OTN-FEC. These descriptions establish its principal use in carrier-grade Ethernet, optical transport, and other high-speed network-interface applications. It is also identified as a telecom interface IC with SFI and XFI serial interfaces, which are important to systems using serializer/deserializer links between line cards, optical modules, and network processors.
Because this product is supplied in a 780-FCBGA package, its implementation is not limited by pin count in the same way as a small-outline package. The package can expose extensive high-speed differential I/O, supply rails, reference interfaces, control signals, and configuration pins. Board design should therefore treat power delivery, return paths, connector and transceiver placement, and thermal spreading as a single system-level problem. The exact pin assignments, voltage requirements, and recommended power architecture should be taken directly from the Microchip product documentation.
Typical applications include 10GbE line cards, optical transport modules, Ethernet aggregation equipment, access and metro network systems, and telecom racks requiring dense high-speed connectivity. In these systems, the device can serve as the line-side Ethernet interface when optical transport requires OTN-FEC and serializer framing alongside 10GbE traffic. Design selection should account for the required number of channels, supported line rate, host interface, optical-module architecture, thermal budget, and board-level test access.
Engineers should use the manufacturer datasheet for the complete 780-ball pin map, recommended power supplies, reference-clock requirements, high-speed differential pair assignments, and PCB stack-up guidance. The package is large and pin-dense, so connector launch geometry, return vias, impedance control, and thermal vias directly affect signal integrity. Avoid making substitute decisions from function descriptions alone; a valid replacement must match the 780-FCBGA footprint, ball assignments, electrical limits, interface configuration, and system-specific requirements.
This product page combines distributor availability references, the manufacturer-direct product result, cross-reference information, and engineering guidance focused on package reuse, signal integrity, thermal design, and qualification. It is intended to help hardware engineers evaluate whether the VSC8494YJE-12 fits a dense 10GbE telecom design and where to obtain the definitive datasheet and current commercial response.
Drop-in alternatives for VSC8494YJE-12 — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.
No drop-in alternatives available for this product.
Request AlternativesVSC8494YJE-12 Specifications
| Product Type | Dual/quad 10GE PHY with OTN-FEC |
| Device Classification | Telecom interface IC / Ethernet switch |
| Ethernet Data Rate | 10 GbE |
| Channel Configuration | Dual/quad |
| Forward Error Correction | OTN-FEC |
| Supported Serial Interfaces | SFI and XFI |
| Package Type | 780-FCBGA |
| Package Dimensions | 29 x 29 mm |
| Package Pin Count | 780 balls |
| Mounting Type | Surface mount |
| Primary Application | Advanced telecom and networking equipment |
| Ethernet Application | 10GbE line-side networking |
| Optical Transport Application | OTN equipment with forward-error correction |
VSC8494YJE-12 780 balls Pin Configuration Guide
Pin configuration for VSC8494YJE-12 (780 balls package). Pin numbering, functions, and connection diagrams are defined in the manufacturer datasheet. Refer to it for the exact footprint and soldering guidelines.
No detailed pinout data available for VSC8494YJE-12.
Refer to the datasheet for full pin configuration.
Typical Applications
VSC8494YJE-12 is suitable for 6 applications: 10GbE Telecom Line Cards, Optical Transport Modules, Carrier Ethernet Aggregation, Metro Network Equipment, Data-Center Network Interface Cards, Network Processor Line Cards.
10GbE Telecom Line Cards
The VSC8494YJE-12 fits a 10GbE line card where the board must terminate multiple high-speed Ethernet lanes and connect them to network-processing or switching electronics. Its dual/quad 10GE PHY description provides a direct architectural match for line-rate Ethernet interfaces, while OTN-FEC can support transport-oriented designs. The 780-FCBGA exposes the numerous I/O, supply, clock, and control connections expected in this application. Layout should use the manufacturer reference design and preserve continuous return paths beneath every high-speed differential pair.
Recommended
Optical Transport Modules
The VSC8494YJE-12 is appropriate for optical transport equipment that combines 10GbE traffic with OTN framing and forward-error-correction functions. Its SFI and XFI interfaces support serial connectivity between the PHY, optical modules, and line-card processing electronics. A designer should allocate separate high-speed routing zones, control impedance through the manufacturer-recommended stack-up, and validate channel loss and jitter with the selected optical and electrical components.
Recommended
Carrier Ethernet Aggregation
Carrier Ethernet aggregation equipment can use the VSC8494YJE-12 at the line-side Ethernet boundary, where multiple 10GbE paths must be converted into serial links for transport circuitry. The dual/quad topology supports denser implementations than a single-lane PHY, while OTN-FEC is useful when the equipment participates in optical transport. Because the device uses a 780-FCBGA, the PCB should provide dense power delivery, many ground connections, and thermal spreading beneath the package.
Recommended
Metro Network Equipment
Metro access and transport systems often combine Ethernet service interfaces with optical line-side processing. The VSC8494YJE-12's dual/quad 10GE PHY capability, OTN-FEC support, and SFI/XFI interfaces align with that architecture. The device should be placed to minimize high-speed trace loss and maintain a short path to clock, optical-module, or network-processor connections. Its large FCBGA requires assembly validation and a thermal design that addresses both steady-state and burst traffic conditions.
Recommended
Data-Center Network Interface Cards
The VSC8494YJE-12 can serve in a specialized 10GbE network interface card when OTN-FEC and SFI/XFI connectivity justify the high-density implementation. It is most relevant to carrier-grade, edge, or aggregation hardware rather than ordinary server adapters, where simpler PHYs are often sufficient. The board must satisfy the manufacturer's high-speed layout rules, isolate noisy digital return currents, and provide robust clock distribution to achieve repeatable line-rate operation.
Recommended
Network Processor Line Cards
A network-processor line card can use the VSC8494YJE-12 as its high-speed Ethernet-facing interface when the system needs 10GbE lanes combined with transport-oriented FEC. SFI and XFI provide serial links suitable for connecting the PHY section to processors, optical components, or fabric devices. Placement should account for package escape routing and the associated connector or optical-module geometry. Power sequencing and channel-by-channel testing should follow the manufacturer reference design.
Recommended
Recommended Products Summary
Engineering reference data for VSC8494YJE-12 — comparison, design guidance, and compliance information.
Selection Guide
Design Notes
Use the manufacturer's recommended PCB stack-up, differential impedance, via geometry, and high-speed escape-routing rules for the 780-FCBGA. Maintain a continuous reference plane beneath every high-speed pair, avoid plane splits in the SFI and XFI routing region, and apply the specified length and loss-management techniques. Validate the final design with the intended board material and the assembled module or line card, including connector and package parasitics.
Treat the 780-FCBGA power grid as a complete distribution network rather than a generic set of package balls. Follow the manufacturer plane, via, decoupling, and isolation guidance exactly, and provide local bulk and high-frequency decoupling at each specified rail. Keep switching-converter and digital return currents out of the sensitive analog or high-speed reference paths. Verify rail sequencing, startup behavior, voltage tolerance, and ripple against the datasheet limits.
Plan copper spreading, thermal vias, airflow, and enclosure heat removal for the full 29 x 29 mm FCBGA rather than for its connector area. The dense package can concentrate heat beneath the die, and telecom line cards may operate in constrained racks. Use the manufacturer's power-loss and junction-temperature guidance, model worst-case traffic and ambient conditions, and verify the assembled board with thermocouples or an infrared measurement campaign.
Do not substitute a generic Ethernet PHY based only on the 10GbE label. A valid board replacement must match the 780-FCBGA footprint, ball assignments, voltage domains, clocking, SFI/XFI behavior, OTN-FEC requirements, and configuration method. Also avoid treating a distributor's functional category as a complete datasheet specification; verify electrical limits, pin states, reset behavior, reference clock requirements, and supported test procedures directly with Microchip documentation.
Compliance Information
No specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declarations were identified in the available product information.