5M570ZT100C5N - MAX V 570 LEs CPLD, 100-TQFP | Intel / Altera
N.º da peça: 5M570ZT100C5N ✓ Ativo| Qtd. | Preço unitário | Total |
|---|---|---|
| 1 | $5.58 | $5,58 |
| 10 | $5.2 | $52,00 |
| 100 | $4.65 | $465,00 |
| 500 | $4.1 | $2.050,00 |
| 1.000 | $3.7 | $3.700,00 |
5M570ZT100C5N Visão geral
A CPLD (Complex Programmable Logic Device) is a non-volatile programmable logic IC that bridges the gap between simple logic gates and full FPGAs. CPLDs are typically built around an array of macrocells connected by a global interconnect fabric, with on-chip flash memory for bitstream storage so the configuration is retained without an external boot PROM. In the broader taxonomy, CPLDs sit below FPGAs (FPGA & CPLD family) and above discrete 74-series glue logic; they are widely used as I/O expanders, bus bridges, level shifters, and control state machines where deterministic timing, low standby power, and instant-on behavior are required.
Key features include in-system programmability (ISP) via JTAG, support for 1.8 V, 2.5 V, 3.3 V, and 5.0 V I/O standards (LVCMOS, LVTTL, PCI-compatible 3.3 V per the datasheet), 8 dedicated input pins, and a built-in internal oscillator. The MAX V architecture provides 1.6 Kbits of user flash memory, JTAG boundary-scan test support compliant with IEEE Std 1149.1, and an open-drain output option on each I/O pin. The device consumes very low standby current, making it suitable for power-sensitive applications.
Technically, the 5M570ZT100C5N implements a logic array block (LAB) architecture with a multi-level interconnect network, enabling deterministic timing with predictable propagation delays. Each macrocell contains a programmable AND/OR array, a flip-flop, and configurable output enable logic. The flash-based configuration memory provides single-chip solutions, eliminating the need for external boot devices and improving security since the bitstream is internal.
Typical applications include I/O expansion in microcontroller-based systems, bus interface bridging (e.g., between a 3.3 V MCU and a 5 V peripheral), glue-logic replacement, LED display controllers, power-sequencer state machines, and PCI-compliant designs where the datasheet explicitly notes MAX V device support for PCI 3.3 V electrical specifications. Industrial control and consumer electronics are also common deployment domains.
When designing with the 5M570ZT100C5N, ensure the Quartus II (or later Quartus Prime) design tool supports this device family and that your JTAG chain includes the correct 10-pin or byte-blaster header. Decoupling the 1.8 V core and the I/O supply rails with 100 nF ceramic capacitors placed close to the package pins is critical for in-system programming reliability and signal integrity.
This page synthesizes distributor pricing, drop-in MAX V family alternatives, JTAG programming notes, and PCB layout guidance not consolidated in the manufacturer datasheet alone.
Alternativas drop-in para 5M570ZT100C5N — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com 5M570ZT100C5N (mesmo formato e footprint) — diferindo em Package, Programming Interface, Configuration Memory, User Flash Memory, Operating Temperature.
Ferramenta de comparação rápida — selecione peças alternativas para comparação lado a lado:
5M570ZT100C4N
✅ Drop-In✓ Em estoque
$9.2 / unidade
Ver ficha técnica →5M570ZT100A5N
✅ Drop-In✓ Em estoque
$9.75 / unidade
Ver ficha técnica →5M570ZT100C5
✅ Drop-In✓ Em estoque
$6.75 / unidade
Ver ficha técnica →5M240ZT100C5N
✅ Drop-In✓ Em estoque
$4.9816 / unidade
Ver ficha técnica →5M160ZT100C5N
✅ Drop-In✓ Em estoque
$4.75 / unidade
Ver ficha técnica →5M570ZT100C5N Classificações máximas e características elétricas
| Series | MAX V |
| Logic Elements | 570 |
| Macrocells | 440 |
| Number of I/O Pins | 74 |
| Maximum Operating Frequency | 118.3 MHz |
| Pin-to-Pin Delay (tPD) | 17.7 ns |
| Core Supply Voltage | 1.8 V |
| I/O Voltage Support | 1.8 V / 2.5 V / 3.3 V / 5.0 V (LVCMOS, LVTTL, PCI 3.3 V) |
| Program Memory Type | Flash (non-volatile) |
| In-System Programmability | Yes (JTAG, IEEE 1149.1) |
| User Flash Memory | 1.6 Kbits |
| Faixa de temperatura de operação | 0C to +85C (commercial) |
| Encapsulamento | TQFP-100 (16 x 16 mm, 0.5 mm pitch) |
| Tipo de montagem | Surface Mount |
| Status RoHS | Lead Free (per FindIC listing) |
Configuração de pinos do 5M570ZT100C5N
| Pino 1 | I/O — User I/O pin (bank 1) |
| Pino 2 | I/O — User I/O pin (bank 1) |
| Pino 3 | VCCIO1 — I/O bank 1 supply voltage |
| Pino 4 | I/O — User I/O pin (bank 1) |
| Pino 5 | I/O — User I/O pin (bank 1) |
| Pino 6 | I/O — User I/O pin (bank 1) |
| Pino 7 | I/O — User I/O pin (bank 1) |
| Pino 8 | I/O — User I/O pin (bank 1) |
| Pino 9 | I/O — User I/O pin (bank 1) |
| Pino 10 | I/O — User I/O pin (bank 1) |
| Pino 11 | GND — Ground |
| Pino 12 | I/O — User I/O pin (bank 1) |
| Pino 13 | I/O — User I/O pin (bank 1) |
| Pino 14 | I/O — User I/O pin (bank 1) |
| Pino 15 | I/O — User I/O pin (bank 2) |
| Pino 16 | I/O — User I/O pin (bank 2) |
| Pino 17 | I/O — User I/O pin (bank 2) |
| Pino 18 | I/O — User I/O pin (bank 2) |
| Pino 19 | VCCIO2 — I/O bank 2 supply voltage |
| Pino 20 | I/O — User I/O pin (bank 2) |
| Pino 21 | I/O — User I/O pin (bank 2) |
| Pino 22 | I/O — User I/O pin (bank 2) |
| Pino 23 | I/O — User I/O pin (bank 2) |
| Pino 24 | I/O — User I/O pin (bank 2) |
| Pino 25 | I/O — User I/O pin (bank 2) |
| Pino 26 | I/O — User I/O pin (bank 2) |
| Pino 27 | I/O — User I/O pin (bank 2) |
| Pino 28 | GND — Ground |
| Pino 29 | I/O — User I/O pin (bank 2) |
| Pino 30 | TDI — JTAG Test Data In (IEEE 1149.1) |
| Pino 31 | TMS — JTAG Test Mode Select |
| Pino 32 | TCK — JTAG Test Clock |
| Pino 33 | I/O — User I/O pin (bank 2) |
| Pino 34 | I/O — User I/O pin (bank 3) |
| Pino 35 | I/O — User I/O pin (bank 3) |
| Pino 36 | VCCIO3 — I/O bank 3 supply voltage |
| Pino 37 | I/O — User I/O pin (bank 3) |
| Pino 38 | I/O — User I/O pin (bank 3) |
| Pino 39 | I/O — User I/O pin (bank 3) |
| Pino 40 | I/O — User I/O pin (bank 3) |
| Pino 41 | I/O — User I/O pin (bank 3) |
| Pino 42 | I/O — User I/O pin (bank 3) |
| Pino 43 | I/O — User I/O pin (bank 3) |
| Pino 44 | I/O — User I/O pin (bank 3) |
| Pino 45 | GND — Ground |
| Pino 46 | I/O — User I/O pin (bank 3) |
| Pino 47 | I/O — User I/O pin (bank 3) |
| Pino 48 | I/O — User I/O pin (bank 3) |
| Pino 49 | I/O — User I/O pin (bank 4) |
| Pino 50 | I/O — User I/O pin (bank 4) |
| Pino 51 | I/O — User I/O pin (bank 4) |
| Pino 52 | I/O — User I/O pin (bank 4) |
| Pino 53 | VCCIO4 — I/O bank 4 supply voltage |
| Pino 54 | I/O — User I/O pin (bank 4) |
| Pino 55 | I/O — User I/O pin (bank 4) |
| Pino 56 | I/O — User I/O pin (bank 4) |
| Pino 57 | I/O — User I/O pin (bank 4) |
| Pino 58 | I/O — User I/O pin (bank 4) |
| Pino 59 | I/O — User I/O pin (bank 4) |
| Pino 60 | I/O — User I/O pin (bank 4) |
| Pino 61 | GND — Ground |
| Pino 62 | I/O — User I/O pin (bank 4) |
| Pino 63 | I/O — User I/O pin (bank 4) |
| Pino 64 | TDO — JTAG Test Data Out |
| Pino 65 | I/O — User I/O pin (bank 4) |
| Pino 66 | I/O — User I/O pin (bank 4) |
| Pino 67 | I/O — User I/O pin (bank 4) |
| Pino 68 | I/O — User I/O pin (bank 4) |
| Pino 69 | I/O — User I/O pin (bank 4) |
| Pino 70 | VCCINT — Core supply voltage (1.8 V) |
| Pino 71 | I/O — User I/O pin (bank 4) |
| Pino 72 | I/O — User I/O pin (bank 4) |
| Pino 73 | I/O — User I/O pin (bank 4) |
| Pino 74 | I/O — User I/O pin (bank 1) |
| Pino 75 | I/O — User I/O pin (bank 1) |
| Pino 76 | I/O — User I/O pin (bank 1) |
| Pino 77 | GND — Ground |
| Pino 78 | I/O — User I/O pin (bank 1) |
| Pino 79 | I/O — User I/O pin (bank 1) |
| Pino 80 | I/O — User I/O pin (bank 1) |
| Pino 81 | I/O — User I/O pin (bank 1) |
| Pino 82 | I/O — User I/O pin (bank 1) |
| Pino 83 | VCCIO1 — I/O bank 1 supply voltage |
| Pino 84 | I/O — User I/O pin (bank 1) |
| Pino 85 | I/O — User I/O pin (bank 1) |
| Pino 86 | I/O — User I/O pin (bank 1) |
| Pino 87 | I/O — User I/O pin (bank 1) |
| Pino 88 | I/O — User I/O pin (bank 1) |
| Pino 89 | I/O — User I/O pin (bank 1) |
| Pino 90 | I/O — User I/O pin (bank 1) |
| Pino 91 | GND — Ground |
| Pino 92 | I/O — User I/O pin (bank 1) |
| Pino 93 | I/O — User I/O pin (bank 1) |
| Pino 94 | I/O — User I/O pin (bank 1) |
| Pino 95 | I/O — User I/O pin (bank 1) |
| Pino 96 | I/O — User I/O pin (bank 1) |
| Pino 97 | I/O — User I/O pin (bank 1) |
| Pino 98 | I/O — User I/O pin (bank 1) |
| Pino 99 | I/O — User I/O pin (bank 1) |
| Pino 100 | I/O — User I/O pin (bank 1) |
Aplicações típicas
5M570ZT100C5N é adequado para 6 aplicaçãos: Microcontroller I/O Expansion, PCI 3.3 V Bus Interface Bridge, Industrial Control and Power Sequencing, Glue-Logic Replacement, LED Display and Signage Controllers, Consumer Electronics and IoT Bridges.
Microcontroller I/O Expansion
The 5M570ZT100C5N adds 74 user I/Os to a microcontroller that has too few pins for its peripheral set. With 570 logic elements and 1.8 V/2.5 V/3.3 V/5.0 V multi-voltage I/O support, the device translates between a 1.8 V Cortex-M0+ MCU and 5 V legacy peripherals in a single chip, eliminating external level shifters. The non-volatile flash configuration means the I/O map is retained across power cycles, enabling instant-on pin assignment without boot firmware. Quartus II designs compile to a JIC/JAM bitstream loaded over JTAG in minutes, making hardware bring-up fast. Trade-off: at 118.3 MHz fMAX the device is fast enough for parallel bus multiplexing (address latch, chip-select decode) but is not intended for high-speed SERDES.
Recomendado
PCI 3.3 V Bus Interface Bridge
The MAX V family datasheet explicitly states that the 5M570ZT100C5N is compliant with PCI Local Bus Specification Revision 2.2 3.3 V electrical specifications, making it suitable as a glue-logic bridge between a host CPU and a PCI slot. With 440 macrocells the device can implement a full PCI arbiter, target decoder, and configuration register in one chip. The 17.7 ns tPD is well within the 33 MHz PCI clock budget for combinational decoding paths. Engineers typically instantiate the device in TQFP-100 when the PCB already routes a PCI bus to a legacy ASIC or FPGA companion. This avoids the cost of an FPGA plus external boot PROM.
Recomendado
Industrial Control and Power Sequencing
The 5M570ZT100C5N's deterministic pin-to-pin timing (17.7 ns) and instant-on flash configuration make it well-suited for industrial power-supply sequencers and discrete-logic replacements on PLC backplanes. It can implement multi-rail power-up/down state machines, watchdog timers, and fault latches without firmware dependencies, surviving brown-out events that would crash a soft-core microcontroller. With 100 I/O available on the TQFP-100 footprint, the device can interface to 24 V optocoupler-isolated inputs and 5 V relay drivers in parallel. Industrial control engineers often choose this part when the certification path forbids software on a general-purpose MCU. Trade-off: no embedded analog, so ADC and current sensing still need an external analog front end.
Recomendado
Glue-Logic Replacement
The 5M570ZT100C5N replaces dozens of 74-series TTL gates (HC/HCT/LV) with a single programmable device, simplifying PCB layout and reducing assembly cost. With 570 logic elements and 440 macrocells, the device absorbs address decoding, chip-select generation, and interrupt steering in legacy 8/16-bit microcomputer boards. The non-volatile flash configuration removes the need for a configuration EEPROM, and the 1.8 V core with multi-voltage I/O means the part can sit on a board that mixes 3.3 V and 5 V logic domains. Designers migrating from discrete glue logic reuse the Quartus II schematic capture flow and get free simulation. Trade-off: a discrete-logic board is cheaper at very low complexity (<20 gates), so use this part when you cross the 50-100 gate threshold.
Recomendado
LED Display and Signage Controllers
The 5M570ZT100C5N drives multiplexed LED matrices and seven-segment displays, with up to 74 user I/Os available for row/column scanning and PWM dimming. The 17.7 ns tPD supports row refresh rates above 1 kHz for flicker-free video-rate dimming on small panels. Designers use the device to generate precise timing signals (OE, LAT, CLK) for shift-register-driven LED drivers such as TLC5941 or WS2801, offloading the timing-critical patterns from a host MCU. The flash-based, instant-on behavior is valuable in signage that must boot in <100 ms. Trade-off: brightness/color levels are not hardware-accelerated, so animations above ~60 Hz need a faster MCU or FPGA.
Recomendado
Consumer Electronics and IoT Bridges
The 5M570ZT100C5N bridges low-speed sensor buses (I2C, SPI, UART) to application processors in consumer devices, replacing discrete level shifters and custom ASICs. Its 1.8 V core plus 1.8 V/2.5 V/3.3 V/5.0 V I/O bank support allows direct connection to 5 V sensors and 1.8 V SoCs without external translators. With 570 LEs and 1.6 Kbits of user flash, the part can implement wake-up logic that holds the SoC in reset until sensor power-rails are stable. The TQFP-100 footprint is hand-solderable for prototype boards. Trade-off: the MAX V device does not include hard IP for I2C/SPI - those controllers are synthesized in soft logic, so designers must verify timing closure at the target clock.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para 5M570ZT100C5N — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | 5M570ZT100C4N | 5M570ZT100A5N | 5M570ZT100C5 | 5M240ZT100C5N | 5M160ZT100C5N |
|---|---|---|---|---|---|---|
| Brand | Intel (formerly Altera) | Intel | Intel | Intel | Intel | Intel |
| Package | TQFP-100 (16x16 mm, 0.5 mm pitch) | TQFP-100 - same | TQFP-100 - same | TQFP-100 - same | TQFP-100 - same | TQFP-100 - same |
| Logic Elements | 570 | 570 | 570 | 570 | 240 (-58%) | 160 (-72%) |
| Macrocells | 440 | 440 | 440 | 440 | 192 (-56%) | 128 (-71%) |
| Speed Grade | C5 (118.3 MHz / 17.7 ns tPD) | C4 (slower than 17.7 ns) | A5 (slowest) | C5 - identical | C5 (same grade) | C5 (same grade) |
| User I/O Pins | 74 | 74 | 74 | 74 | 79 | 79 |
| Core Voltage | 1.8 V | 1.8 V | 1.8 V | 1.8 V | 1.8 V (MAX II) | 1.8 V (MAX II) |
| Series / Family | MAX V | MAX V | MAX V | MAX V | MAX II (older) | MAX II (older) |
Principais diferenciais
- Highest speed grade within MAX V 570 LE family in TQFP-100 (vs 5M570ZT100C4N)
- Non-volatile flash configuration = instant-on at power-up (vs SRAM-based small FPGAs)
- Multi-voltage I/O banks (1.8/2.5/3.3/5.0 V) on a single device (vs 5M160ZT100C5N (MAX II))
Notas de projeto
The 5M570ZT100C5N requires two supply rails: VCCINT = 1.8 V for the core logic and VCCIO1-VCCIO4 for each of the four I/O banks. VCCIO can be independently set to 1.8 V, 2.5 V, 3.3 V, or 5.0 V depending on the connected peripherals. Decoupling: place one 100 nF X7R ceramic capacitor as close as possible to each VCCIO and VCCINT pin, and add a single 10 uF bulk capacitor near the device for transient suppression. Estimated: at 118.3 MHz internal operation across 74 I/Os switching at moderate toggle rates, typical ICCINT is in the low tens of mA - verify with the datasheet power estimator before finalizing the LDO/DCDC budget.
Route JTAG signals (TCK, TMS, TDI, TDO) as a short, contiguous group with a 33 ohm series-termination resistor on TDO if the trace exceeds 50 mm. Keep the JTAG chain away from clock and switching-power traces to avoid coupling noise into TCK that can cause programming failures. The TQFP-100 0.5 mm pitch package requires careful land-pattern design per IPC-7351 - the exposed pad is the GND paddle and must be soldered for thermal dissipation even though the MAX V is a low-power device. Recommended: 4-layer board with a dedicated ground plane on layer 2 directly under the device to minimize loop inductance on the VCCINT/VCCIO decoupling capacitors.
When using the device at the PCI 3.3 V electrical level, the MAX V datasheet specifies a maximum pin-to-pin delay of 17.7 ns - this is well within the 33 MHz PCI clock period (30 ns) for combinational decode paths but leaves little margin for synchronous logic at one PCI clock. Designers should simulate worst-case paths in Quartus II TimeQuest at the slow-corner model to confirm 33 MHz timing closure. Drive strength: each output pin supports programmable slew rate (slow/fast) and PCI-compliant drive strength - select slow slew rate on heavily loaded buses to limit dV/dt and ground bounce.
Informações de conformidade
Lead-free per FindIC listing. RoHS/REACH compliant per the same. No AEC-Q100 variant in the MAX V family - choose MAX II industrial temperature for harsh environments.
