5M80ZT100A5N - 64-Macrocell MAX V CPLD, 100-TQFP, 1.8V | Altera
料号： 5M80ZT100A5N ✓ 量产中| 数量 | 单价 | 小计 |
|---|---|---|
| 1 | $2.95 | $2.95 |
| 10 | $2.65 | $26.50 |
| 100 | $2.3 | $230.00 |
| 500 | $2.05 | $1,025.00 |
| 1,000 | $1.85 | $1,850.00 |
5M80ZT100A5N 概述
A CPLD (Complex Programmable Logic Device) is a non-volatile programmable logic device that bridges the gap between simple PLDs and larger FPGAs. In the broader programmable logic taxonomy, CPLDs sit between PAL/GAL (small, simple) and FPGAs (large, register-rich, volatile SRAM-based). MAX V CPLDs use a flash-based configuration cell that retains bitstream without an external boot PROM, which simplifies board design and reduces BOM cost versus SRAM-based FPGAs. The 5M80ZT100A5N therefore occupies a 'low-density, instant-on, deterministic-timing' niche well above discrete 74HC logic but below the smallest Cyclone FPGA.
Key features include 64 logic macrocells (each containing a 36-input product term and one flip-flop), 80 user I/O pins on the TQFP-100 package, an integrated 1.8 V core with 1.8 V/2.5 V/3.3 V multi-voltage I/O support through bank-level VCCIO rails, and an embedded user flash memory block (UFM) of 8 Kbits that can be used for configuration storage or general-purpose non-volatile data. The device supports in-system programmability via JTAG (IEEE 1149.1) and operates across the industrial -40 C to +125 C junction temperature range. The 1.8 V core core voltage combined with the legacy 3.3 V/2.5 V I/O bank options makes the 5M80ZT100A5N a practical 'bridge' between modern low-voltage processors and older peripheral ICs.
The 5M80ZT100A5N's 7.5 ns tPD and deterministic 118.3 MHz fMAX suit it for bus-interface decoding, address latch/buffer logic, asynchronous state machines, and small FIFO glue. The MAX V architecture uses a uniform interconnect matrix with predictable routing delays, so timing closure does not require place-and-route iteration as with FPGAs - timing is largely data-sheet-driven.
Typical applications include industrial control boards (sensor aggregation, motor-driver interface decoding), automotive body-electronics modules (AEC-Q100 qualified variants exist in this family), consumer-electronics glue logic between ASSPs and I/O connectors, and any system requiring instant-on, non-volatile logic with sub-10 ns decode paths. A common pattern is replacing 4-8 discrete 74-series packages with a single 5M80ZT100A5N to free PCB area and reduce assembly cost.
When designing with this part, choose VCCIO per bank based on the connected peripherals (1.8 V, 2.5 V, or 3.3 V), connect JTAG TMS/TCK/TDO/TDI to a header for in-system programming, and provide a clean 1.8 V core supply (VCCINT) with at least one 0.1 uF decoupling capacitor per supply pin. The Quartus II / Quartus Prime toolchain generates the JEDEC programming file. Note that MAX V devices are mature - newer MAX 10 / MAX II families may be considered if higher logic density is needed, but they are not pin-compatible with this TQFP-100 footprint.
直接替换替代料： 5M80ZT100A5N ——相同封装，引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号： 5M80ZT100A5N （相同外形与封装尺寸） ——差异在于 Configuration Memory, Package, Programming Interface, User Flash Memory, I/O Voltage (VCCIO).
快速对比工具——选择替代料号进行并排对比：
5M80ZT100I5N
✅ 直接替换✓ 有现货
$7.3749 / 个
查看数据手册 →5M80ZT100C5N
✅ 直接替换✓ 有现货
$4.1 / 个
查看数据手册 →5M160ZT100A5N
✅ 直接替换✓ 有现货
$4.9 / 个
查看数据手册 →5M240ZT100A5N
✅ 直接替换✓ 有现货
$6.1 / 个
查看数据手册 →5M570ZT100A5N
✅ 直接替换✓ 有现货
$9.75 / 个
查看数据手册 →5M80ZT100A5N 最大额定值与电气特性
| Family | MAX V |
| Macro Cells | 64 |
| Logic Elements / LABs | 8 Logic Array Blocks (LABs) |
| Maximum User I/O | 80 (in TQFP-100 package) |
| Pin-to-Pin Propagation Delay (tPD) | 7.5 ns |
| Maximum Internal Frequency (fMAX) | 118.3 MHz |
| Core Supply Voltage (VCCINT) | 1.8 V |
| I/O Bank Supply Voltage (VCCIO) | 1.2 V / 1.5 V / 1.8 V / 2.5 V / 3.3 V (multi-voltage banks) |
| User Flash Memory (UFM) | 8 Kbits (typical for MAX V 64-macrocell device) |
| Configuration Memory | Non-volatile, on-chip flash |
| Programming Interface | JTAG (IEEE 1149.1 / IEEE 1532) |
| 工作结温 | -40 C to +125 C (automotive/industrial grade) |
| 封装 | 100-pin TQFP (T100) |
| 安装类型 | Surface Mount |
| MSL 等级 | 3 (per JEDEC J-STD-020) |
| RoHS 状态 | Compliant |
| Automotive Qualification | AEC-Q100 (A5N suffix) |
| Global Clock Networks | 4 |
| Lead-Free / Halogen-Free | Yes / Yes (per Altera lead-free roadmap) |
5M80ZT100A5N 引脚配置
| 引脚 1 | I/O — General-purpose user I/O (bank 3) |
| 引脚 2 | I/O — General-purpose user I/O (bank 3) |
| 引脚 3 | I/O — General-purpose user I/O (bank 3) |
| 引脚 4 | I/O — General-purpose user I/O (bank 3) |
| 引脚 5 | I/O — General-purpose user I/O (bank 3) |
| 引脚 6 | I/O — General-purpose user I/O (bank 3) |
| 引脚 7 | VCCIO3 — I/O bank 3 supply voltage |
| 引脚 8 | I/O — General-purpose user I/O (bank 3) |
| 引脚 9 | I/O — General-purpose user I/O (bank 3) |
| 引脚 10 | GND — Ground |
| 引脚 11 | I/O — General-purpose user I/O (bank 3) |
| 引脚 12 | I/O — General-purpose user I/O (bank 3) |
| 引脚 13 | I/O — General-purpose user I/O (bank 3) |
| 引脚 14 | I/O — General-purpose user I/O (bank 3) |
| 引脚 15 | I/O — General-purpose user I/O (bank 3) |
| 引脚 16 | I/O — General-purpose user I/O (bank 3) |
| 引脚 17 | I/O — General-purpose user I/O (bank 3) |
| 引脚 18 | I/O — General-purpose user I/O (bank 3) |
| 引脚 19 | VCCINT — Core supply voltage 1.8 V |
| 引脚 20 | I/O — General-purpose user I/O (bank 3) |
| 引脚 21 | I/O — General-purpose user I/O (bank 3) |
| 引脚 22 | GND — Ground |
| 引脚 23 | I/O — General-purpose user I/O (bank 3) |
| 引脚 24 | I/O — General-purpose user I/O (bank 3) |
| 引脚 25 | I/O — General-purpose user I/O (bank 3) |
| 引脚 26 | I/O — General-purpose user I/O (bank 3) |
| 引脚 27 | I/O — General-purpose user I/O (bank 3) |
| 引脚 28 | I/O — General-purpose user I/O (bank 3) |
| 引脚 29 | I/O — General-purpose user I/O (bank 3) |
| 引脚 30 | I/O — General-purpose user I/O (bank 3) |
| 引脚 31 | GND — Ground |
| 引脚 32 | I/O — General-purpose user I/O (bank 3) |
| 引脚 33 | I/O — General-purpose user I/O (bank 3) |
| 引脚 34 | I/O — General-purpose user I/O (bank 3) |
| 引脚 35 | VCCIO3 — I/O bank 3 supply voltage |
| 引脚 36 | I/O — General-purpose user I/O (bank 3) |
| 引脚 37 | I/O — General-purpose user I/O (bank 3) |
| 引脚 38 | I/O — General-purpose user I/O (bank 3) |
| 引脚 39 | I/O — General-purpose user I/O (bank 3) |
| 引脚 40 | TDI — JTAG Test Data In |
| 引脚 41 | TMS — JTAG Test Mode Select |
| 引脚 42 | TCK — JTAG Test Clock |
| 引脚 43 | GND — Ground |
| 引脚 44 | TDO — JTAG Test Data Out |
| 引脚 45 | I/O — General-purpose user I/O (bank 4) |
| 引脚 46 | I/O — General-purpose user I/O (bank 4) |
| 引脚 47 | I/O — General-purpose user I/O (bank 4) |
| 引脚 48 | I/O — General-purpose user I/O (bank 4) |
| 引脚 49 | I/O — General-purpose user I/O (bank 4) |
| 引脚 50 | I/O — General-purpose user I/O (bank 4) |
| 引脚 51 | GND — Ground |
| 引脚 52 | I/O — General-purpose user I/O (bank 4) |
| 引脚 53 | I/O — General-purpose user I/O (bank 4) |
| 引脚 54 | VCCIO4 — I/O bank 4 supply voltage |
| 引脚 55 | I/O — General-purpose user I/O (bank 4) |
| 引脚 56 | I/O — General-purpose user I/O (bank 4) |
| 引脚 57 | I/O — General-purpose user I/O (bank 4) |
| 引脚 58 | I/O — General-purpose user I/O (bank 4) |
| 引脚 59 | I/O — General-purpose user I/O (bank 4) |
| 引脚 60 | I/O — General-purpose user I/O (bank 4) |
| 引脚 61 | GND — Ground |
| 引脚 62 | I/O — General-purpose user I/O (bank 4) |
| 引脚 63 | I/O — General-purpose user I/O (bank 4) |
| 引脚 64 | I/O — General-purpose user I/O (bank 4) |
| 引脚 65 | I/O — General-purpose user I/O (bank 4) |
| 引脚 66 | VCCINT — Core supply voltage 1.8 V |
| 引脚 67 | I/O — General-purpose user I/O (bank 4) |
| 引脚 68 | I/O — General-purpose user I/O (bank 4) |
| 引脚 69 | I/O — General-purpose user I/O (bank 4) |
| 引脚 70 | I/O — General-purpose user I/O (bank 4) |
| 引脚 71 | I/O — General-purpose user I/O (bank 4) |
| 引脚 72 | GND — Ground |
| 引脚 73 | I/O — General-purpose user I/O (bank 1) |
| 引脚 74 | I/O — General-purpose user I/O (bank 1) |
| 引脚 75 | VCCIO1 — I/O bank 1 supply voltage |
| 引脚 76 | I/O — General-purpose user I/O (bank 1) |
| 引脚 77 | I/O — General-purpose user I/O (bank 1) |
| 引脚 78 | I/O — General-purpose user I/O (bank 1) |
| 引脚 79 | I/O — General-purpose user I/O (bank 1) |
| 引脚 80 | I/O — General-purpose user I/O (bank 1) |
| 引脚 81 | I/O — General-purpose user I/O (bank 1) |
| 引脚 82 | GND — Ground |
| 引脚 83 | I/O — General-purpose user I/O (bank 1) |
| 引脚 84 | I/O — General-purpose user I/O (bank 1) |
| 引脚 85 | I/O — General-purpose user I/O (bank 1) |
| 引脚 86 | I/O — General-purpose user I/O (bank 1) |
| 引脚 87 | I/O — General-purpose user I/O (bank 1) |
| 引脚 88 | I/O — General-purpose user I/O (bank 1) |
| 引脚 89 | I/O — General-purpose user I/O (bank 1) |
| 引脚 90 | I/O — General-purpose user I/O (bank 1) |
| 引脚 91 | GND — Ground |
| 引脚 92 | I/O — General-purpose user I/O (bank 1) |
| 引脚 93 | I/O — General-purpose user I/O (bank 1) |
| 引脚 94 | I/O — General-purpose user I/O (bank 2) |
| 引脚 95 | I/O — General-purpose user I/O (bank 2) |
| 引脚 96 | I/O — General-purpose user I/O (bank 2) |
| 引脚 97 | VCCIO2 — I/O bank 2 supply voltage |
| 引脚 98 | I/O — General-purpose user I/O (bank 2) |
| 引脚 99 | I/O — General-purpose user I/O (bank 2) |
| 引脚 100 | I/O — General-purpose user I/O (bank 2) |
典型应用
5M80ZT100A5N 适用于 6 应用s: Industrial Control Board Glue Logic, Automotive Body Electronics Module, Consumer Electronics Interface Bridge, Motor Driver Interface Decoder, Communications Equipment Glue Logic, Test and Measurement Front-End Logic.
Industrial Control Board Glue Logic
The 5M80ZT100A5N replaces 4-8 discrete 74HC/74LVC logic packages on industrial PLC and sensor-aggregation boards, freeing PCB area while delivering 7.5 ns tPD for fast bus-decoder paths. Its 1.8 V core with multi-voltage I/O banks bridges a modern ARM Cortex-M0 host processor (1.8 V GPIO) to legacy 3.3 V and 5 V-tolerant peripherals without external level shifters. The -40 C to +125 C junction temperature range and AEC-Q100 'A5N' suffix suit factory-floor and outdoor cabinet deployments where temperature swings and vibration stress rule out consumer-grade parts.
推荐
Automotive Body Electronics Module
In automotive body controllers (BCM), door modules, and HVAC interfaces, the 5M80ZT100A5N serves as the deterministic-logic backbone that decodes CAN/LIN bus wake events, drives relay and LED matrices, and implements safety state machines. The AEC-Q100 qualification and 1.8 V core with 3.3 V I/O tolerance let it interface directly with automotive MCUs and 12 V load-driver ICs. Its non-volatile flash-based configuration means the device comes up in <1 ms after battery reconnect, critical for crash-event data logging and immediate response to ignition-on.
推荐
Consumer Electronics Interface Bridge
The 5M80ZT100A5N bridges modern low-voltage application processors to legacy peripherals in set-top boxes, smart-home hubs, and home appliances - translating 1.8 V I2C/SPI bus signals to 3.3 V UART or GPIO lines without software overhead. Its 80 user I/Os in a 100-TQFP package give designers ample headroom for keypad scanning, LED multiplexing, and rotary-encoder decoding. The integrated 8-Kbit User Flash Memory (UFM) stores boot configuration, calibration constants, and product serial numbers, eliminating an external EEPROM.
推荐
Motor Driver Interface Decoder
Between a microcontroller and a multi-axis stepper or BLDC driver, the 5M80ZT100A5N implements direction logic, PWM distribution, fault-mux decoding, and home-switch conditioning in a single package. Its 7.5 ns tPD keeps the PWM-to-driver propagation well below typical 20 kHz PWM periods, ensuring phase-timing fidelity. The multi-voltage VCCIO banks let one CPLD talk to a 1.8 V MCU on one side and 3.3 V gate drivers on the other, eliminating a level-shifter IC and reducing BOM cost on CNC, 3D-printer, and robotics control boards.
推荐
Communications Equipment Glue Logic
In networking line cards, small-cell base stations, and industrial Ethernet switches, the 5M80ZT100A5N performs address decoding, FIFO flag combination, LED-status multiplexing, and clock-domain crossing between PHY, switch ASIC, and management CPU. Its 118.3 MHz fMAX on global clocks handles 100 Mbps Ethernet MDIO bus timing without metastability issues, and its non-volatile configuration ensures immediate post-boot readiness without an external configuration PROM. The 100-TQFP footprint exposes 80 user I/Os, sufficient for typical 24-port switch front-panel indicator designs.
推荐
Test and Measurement Front-End Logic
Bench-top oscilloscopes, data loggers, and lab instrumentation use the 5M80ZT100A5N to implement front-panel button de-bouncing, rotary-encoder quadrature decoding, range-relay selection, and trigger-arm logic. Its deterministic 7.5 ns tPD ensures trigger-arming latencies stay below the instrument's specified trigger jitter budget. The User Flash Memory block stores calibration coefficients and serial numbers, while JTAG (IEEE 1149.1) enables in-system firmware updates in the field without removing the instrument from service.
推荐
推荐产品汇总
工程参考数据： 5M80ZT100A5N ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | 5M80ZT100I5N | 5M80ZT100C5N | 5M160ZT100A5N | 5M240ZT100A5N | 5M570ZT100A5N |
|---|---|---|---|---|---|---|
| Package | TQFP-100 | TQFP-100 - same | TQFP-100 - same | TQFP-100 - same | TQFP-100 - same | TQFP-100 - same |
| Brand | Altera (Intel) | Altera (Intel) | Altera (Intel) | Altera (Intel) | Altera (Intel) | Altera (Intel) |
| Macro Cells | 64 | 64 | 64 | 160 | 240 | 570 |
| Pin-to-Pin Delay (tPD) | 7.5 ns | 7.5 ns | 7.5 ns | 7.5 ns | 7.5 ns | 7.5 ns |
| Temperature Grade | -40 C to +125 C (AEC-Q100) | -40 C to +100 C (Industrial) | 0 C to +85 C (Commercial) | -40 C to +125 C (AEC-Q100) | -40 C to +125 C (AEC-Q100) | -40 C to +125 C (AEC-Q100) |
| Core Voltage (VCCINT) | 1.8 V | 1.8 V | 1.8 V | 1.8 V | 1.8 V | 1.8 V |
| User I/O Count | 80 | 80 | 80 | 80 | 80 | 80 |
| Configuration Memory | Flash, non-volatile | Flash, non-volatile | Flash, non-volatile | Flash, non-volatile | Flash, non-volatile | Flash, non-volatile |
| Programming Interface | JTAG (IEEE 1149.1) | JTAG (IEEE 1149.1) | JTAG (IEEE 1149.1) | JTAG (IEEE 1149.1) | JTAG (IEEE 1149.1) | JTAG (IEEE 1149.1) |
| Approx. Unit Price @ 1 pc | $2.95 | $2.50 - $2.80 | $2.20 - $2.50 | $5.50 - $7.00 | $8.00 - $10.00 | $14.00 - $18.00 |
关键差异点
- Non-volatile flash-based configuration （对比 Xilinx XC2C32A (CoolRunner-II, SRAM-less but different architecture))
- Multi-voltage I/O bank support （对比 5M80ZE64A5N (same 64 macrocells, 64-EQFP package))
- Automotive-grade qualification with same density （对比 5M80ZT100C5N (commercial grade, same TQFP-100 footprint))
设计说明
The 5M80ZT100A5N requires two distinct supply rails: VCCINT at 1.8 V for the core logic and VCCIO per bank (1.2/1.5/1.8/2.5/3.3 V) for the I/O drivers. Place a 0.1 uF X7R ceramic decoupling capacitor within 3 mm of every VCCINT and VCCIO pin, plus one bulk 10 uF tantalum or ceramic capacitor near the device. Without proper decoupling, simultaneous-switching outputs can inject noise into the JTAG chain and cause JTAG IDCODE readback failures during in-system programming.
Although MAX V CPLDs are CMOS-low-power (typical Icc <50 mA at 1.8 V), the 100-TQFP package has a junction-to-ambient thermal resistance (theta_JA) of approximately 40-50 C/W on a 4-layer JEDEC test board with 2 oz copper. Estimated: at full I/O toggle rate across 80 outputs with 10 pF loads and 25 MHz, junction rise above ambient is under 10 C. No heatsink is required, but for enclosed industrial cabinets operating above 70 C ambient, derate switching frequency or reduce simultaneously-switching I/O count.
Route JTAG signals (TCK, TMS, TDI, TDO) as a daisy-chain with 4.7 kohm pull-ups on TMS and TDI to VCCIO of the JTAG bank, per Altera JTAG configuration guidelines. Keep TCK trace length under 100 mm to avoid signal-integrity issues at high TCK frequencies. The 100-TQFP land pattern has 0.5 mm pitch - use ENIG surface finish and a reflow profile compliant with JEDEC J-STD-020 MSL-3 handling requirements.
Common design pitfalls: (1) Forgetting to set unused I/O pins to 'tri-stated input with weak pull-up' in Quartus, which can leave inputs floating and cause additional supply current; (2) mixing 1.8 V and 3.3 V peripherals in the same I/O bank - VCCIO is per-bank but only one voltage per bank; (3) assuming the part is in-system programmable without JTAG header access - always bring out the 4 JTAG pins plus GND to a test-point footprint for field reprogrammability.
合规信息
AEC-Q100 automotive qualification per the 'A' suffix in 5M80ZT100A5N. RoHS compliant and lead-free per Altera/Intel product declaration. Halogen-free per JEDEC JS709B PCB-material standard. Supply-chain conflict-minerals compliance per Section 1502 of the Dodd-Frank Act.