ADS8688IDBT - 16-Bit 500kSPS 8-Ch SAR ADC | Texas Instruments
N.º da peça: ADS8688IDBT ✓ Ativo| Qtd. | Preço unitário | Total |
|---|---|---|
| 1 | $28.5 | $28,50 |
| 10 | $25.75 | $257,50 |
| 100 | $22.1 | $2.210,00 |
| 500 | $18.4 | $9.200,00 |
| 1.000 | $15.6 | $15.600,00 |
ADS8688IDBT Visão geral
A SAR ADC is a successive-approximation-register analog-to-digital converter that performs a binary search across an internal capacitive DAC to digitize each input sample in one conversion cycle. SAR ADCs offer deterministic latency, no pipeline delay, and excellent DC accuracy, making them the converter of choice for multiplexed data-acquisition front ends, industrial control loops, and precision instrumentation. The ADS8688IDBT sits in the data-acquisition IC taxonomy as: ADC -> SAR ADC -> multi-channel data-acquisition system -> precision analog IC.
Key features include 500 kSPS throughput, 16-bit resolution with no missing codes, ±20V overvoltage-tolerant analog inputs, integrated 8-channel AFE, low-drift 4.096V internal reference with REF-by-default pin mode, and an SPI-compatible serial interface that supports daisy-chaining of multiple devices. The device also includes per-channel programmable input ranges (±12V, ±10V, 0-10V, 0-5V, ±5V) via software configuration and an ALARM/SDO-ABS pin for threshold detection.
The architecture combines a charge-redistribution SAR core with a high-impedance input clamp, input signal conditioning, and an 8:1 input mux. The integrated reference reduces external component count, while the 1.65V-5.25V digital supply enables direct connection to 1.8V, 3.3V, and 5V host controllers without level shifters. Per the TI product page, the device is designed for high-channel-count precision measurement where board area and BOM cost are critical.
Typical applications include industrial process control PLC analog input modules, power automation and protection relays, multi-axis motor drive feedback, battery management system (BMS) cell monitoring, medical instrumentation signal acquisition, and factory-automation sensor aggregation. The bipolar input ranges make it directly compatible with ±10V industrial sensors without external signal conditioning.
When designing with this device, observe proper analog/digital ground partitioning on the PCB and place the 10uF + 1uF AVDD decoupling network within 5mm of the AVDD pin. For optimum performance, use the device's internal reference with the REF-by-default configuration and avoid driving high-impedance sources directly into the analog inputs without a series resistor to limit input current during fault conditions.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found on the TI product page or distributor listings.
Alternativas drop-in para ADS8688IDBT — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com ADS8688IDBT (mesmo formato e footprint) — diferindo em Analog Supply Voltage (AVDD), Input Overvoltage Protection, MSL Level, Operating Temperature Range, Package.
Ferramenta de comparação rápida — selecione peças alternativas para comparação lado a lado:
ADS8688IDBTR
✅ Drop-In✓ Em estoque
$9.85 / unidade
Ver ficha técnica →ADS8688AIDBT
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
ADS8684IDBT
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
ADS8681IDBT
✅ Drop-In ⚠️ Especificações não verificadas📋 Alternativa de referência (fora do catálogo)
ADS8685IDBT
✅ Drop-In ⚠️ Especificações não verificadas📋 Alternativa de referência (fora do catálogo)
ADS8688IDBT Classificações máximas e características elétricas
| Resolução | 16 bits |
| Sample Rate (Throughput) | 500 kSPS |
| Number of Input Channels | 8 |
| Architecture | SAR (Successive Approximation Register) |
| Input Type | Single-ended, pseudo-differential input pair options |
| Analog Supply Voltage (AVDD) | 4.75 V to 5.25 V (5 V typical) |
| Digital I/O Supply (DVDD) | 1.65 V to 5.25 V |
| Analog Input Voltage Range | ±12 V, ±10 V, 0-10 V, 0-5 V, ±5 V (per-channel software selectable) |
| Input Overvoltage Protection | ±20 V (per channel) |
| Internal Reference Voltage | 4.096 V |
| Reference Type | Internal low-drift (REF-by-default pin mode) or external |
| Interface | SPI-compatible, daisy-chain capable |
| Faixa de temperatura de operação | -40 °C to +125 °C |
| Encapsulamento | 38-pin TSSOP (DBT) |
| Tipo de montagem | Surface Mount |
| Nível MSL | 2 (per JEDEC J-STD-020) |
| Lead-Free / RoHS | Yes / Compliant |
Configuração de pinos do ADS8688IDBT
| Pino 1 | AVDD — Analog supply, 5 V |
| Pino 2 | AVSS — Analog ground |
| Pino 3 | REFIO — Reference I/O (4.096 V) |
| Pino 4 | REFCAP — Reference bypass capacitor |
| Pino 5 | REFEN — Reference enable / REF-by-default |
| Pino 6 | AIN0 — Analog input channel 0 |
| Pino 7 | AIN1 — Analog input channel 1 |
| Pino 8 | AIN2 — Analog input channel 2 |
| Pino 9 | AIN3 — Analog input channel 3 |
| Pino 10 | AIN4 — Analog input channel 4 |
| Pino 11 | AIN5 — Analog input channel 5 |
| Pino 12 | AIN6 — Analog input channel 6 |
| Pino 13 | AIN7 — Analog input channel 7 |
| Pino 14 | AVSS — Analog ground |
| Pino 15 | AVDD — Analog supply, 5 V |
| Pino 16 | GND — General ground |
| Pino 17 | DVDD — Digital I/O supply (1.65-5.25 V) |
| Pino 18 | RST/PD — Reset / power-down |
| Pino 19 | CONVST/CS — Conversion start / chip select |
| Pino 20 | SCLK — SPI serial clock |
| Pino 21 | SDI — SPI serial data in |
| Pino 22 | SDO — SPI serial data out |
| Pino 23 | ALARM/SDO-ABS — Alarm output / SDO absolute |
| Pino 24 | GPO0 — General-purpose output 0 |
| Pino 25 | GPO1 — General-purpose output 1 |
| Pino 26 | GPO2 — General-purpose output 2 |
| Pino 27 | GPO3 — General-purpose output 3 |
| Pino 28 | NC — Not connected (per datasheet) |
| Pino 29 | NC — Not connected (per datasheet) |
| Pino 30 | NC — Not connected (per datasheet) |
| Pino 31 | NC — Not connected (per datasheet) |
| Pino 32 | NC — Not connected (per datasheet) |
| Pino 33 | AVSS — Analog ground |
| Pino 34 | AVDD — Analog supply, 5 V |
| Pino 35 | AVSS — Analog ground |
| Pino 36 | AVDD — Analog supply, 5 V |
| Pino 37 | AVSS — Analog ground |
| Pino 38 | DVDD — Digital I/O supply |
Aplicações típicas
ADS8688IDBT é adequado para 6 aplicaçãos: Industrial PLC Analog Input Modules, Power Automation and Protection Relays, Multi-Axis Motor Drive Feedback, Battery Management System (BMS) Cell Monitoring, Medical Instrumentation Signal Acquisition, Factory Automation Sensor Aggregation.
Industrial PLC Analog Input Modules
The ADS8688IDBT's 8 input channels with per-channel software-selectable ±10 V/±12 V bipolar input ranges and ±20 V overvoltage protection map directly to industrial PLC AI module requirements. The integrated 8:1 mux, on-chip 4.096 V reference, and SPI-compatible daisy-chain interface enable multi-slot PLC architectures where one host SPI bus scans >64 channels by chaining multiple ADS8688IDBT devices. At 500 kSPS aggregate throughput, the part can digitize all 8 channels at 62.5 kSPS each, comfortably meeting the update-rate demands of industrial process-control loops driving 4-20 mA sensor aggregation. The TSSOP-38 footprint simplifies thermal and PCB layout within the dense PLC backplane.
Recomendado
Power Automation and Protection Relays
The ADS8688IDBT fits protection-relay analog front ends where 8 bipolar voltage/current channels must be digitized simultaneously for 50/60 Hz power-system monitoring. The 16-bit no-missing-codes resolution, ±10 V input range, and ±20 V overvoltage protection tolerate substation transients without external TVS networks, while the 500 kSPS throughput supports up to 16 kSPS per channel when oversampling from multiple ADS8688IDBT devices daisy-chained across phases. The TSSOP-38 package and 5 V single-supply operation simplify relay-card PCB design, and the digital supply down to 1.65 V enables direct connection to FPGAs implementing IEC 61850 sampling logic.
Recomendado
Multi-Axis Motor Drive Feedback
In multi-axis servo and stepper drives, the ADS8688IDBT digitizes resolver / encoder / Hall-sensor analog signals across 8 channels at 500 kSPS aggregate, supporting current-loop sampling rates >20 kHz per axis when paired with daisy-chained devices. The integrated analog front end with input clamps protects the ADC from motor switching transients up to ±20 V, eliminating external resistor-diode protection networks. The TSSOP-38 footprint and 5 V single-supply operation align with typical 24 V -> 5 V drive-rail power architectures, and the SPI interface connects directly to the drive's DSP or MCU control loop for torque/current feedback.
Recomendado
Battery Management System (BMS) Cell Monitoring
The ADS8688IDBT monitors up to 8 lithium-ion cell voltages simultaneously in a BMS, where the 16-bit resolution maps to <1 mV cell-voltage resolution across a 0-5 V range - sufficient for cell balancing and SOC estimation. The integrated 8:1 mux and 500 kSPS throughput enable <1 ms full-pack scan times, while the TSSOP-38 footprint fits within modular BMS daughter boards stacked on the cell-pack. The on-chip 4.096 V reference with low drift maintains calibration across the -40 to +125 °C automotive operating range, matching the thermal demands of under-hood or cabinet-mounted battery packs.
Recomendado
Medical Instrumentation Signal Acquisition
The ADS8688IDBT acquires up to 8 channels of patient-monitoring analog signals (ECG, SpO2, temperature, respiration) in compact medical instrumentation. The 16-bit no-missing-codes resolution delivers the dynamic range needed for low-amplitude biopotential signals, while the bipolar ±10 V input range accommodates sensor front-end outputs without external signal conditioning. The TSSOP-38 package supports miniaturized bedside-monitor PCBs, and the integrated ±20 V input protection guards against defibrillator and electrosurgical transients when paired with external current-limiting resistors - a common requirement for IEC 60601-1 patient-leakage compliance.
Recomendado
Factory Automation Sensor Aggregation
The ADS8688IDBT aggregates 8 factory-floor sensor inputs (pressure, flow, level, temperature transmitters) into a single SPI stream for PLC or edge-controller processing. The per-channel software-selectable ±10 V/0-10 V/4-20 mA-compatible input ranges match virtually every industrial transmitter output without external conditioning, while the ±20 V overvoltage protection tolerates field-wiring faults. The 500 kSPS throughput supports high-speed control loops, and the daisy-chain SPI interface scales the system beyond 8 channels by stacking multiple ADS8688IDBT devices on a single host CS line, reducing host pin count in dense I/O racks.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para ADS8688IDBT — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | ADS8688IDBTR | ADS8688AIDBT | ADS8684IDBT |
|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 38-TSSOP (DBT) | 38-TSSOP (DBT) - same | 38-TSSOP (DBT) - same | 38-TSSOP (DBT) - same |
| Resolution | 16 bits | 16 bits | 16 bits | 16 bits |
| Sample Rate | 500 kSPS | 500 kSPS | 500 kSPS | 500 kSPS |
| Input Channels | 8 | 8 | 8 | 4 |
| Analog Supply | 5 V (single) | 5 V | 5 V | 5 V |
| Digital Supply | 1.65 V to 5.25 V | 1.65 V to 5.25 V | 1.65 V to 5.25 V | 1.65 V to 5.25 V |
| Input Range | ±10/±12 V bipolar | ±10/±12 V bipolar | ±10/±12 V bipolar | ±10/±12 V bipolar |
| Overvoltage Protection | ±20 V | ±20 V | ±20 V | ±20 V |
| Internal Reference | 4.096 V | 4.096 V | 4.096 V | 4.096 V |
| Interface | SPI, daisy-chain | SPI, daisy-chain | SPI, daisy-chain | SPI, daisy-chain |
Principais diferenciais
- Integrated 8-channel AFE with ±20 V overvoltage protection (vs ADS8684IDBT (4-channel variant))
- Drop-in same-die tape-and-reel carrier option (vs ADS8688IDBTR)
- Minor die-revision drop-in alternative (vs ADS8688AIDBT)
Notas de projeto
Partition the PCB into separate analog and digital ground planes joined at a single point near the ADS8688IDBT AVSS/DGND pins. Place the 10 uF bulk + 1 uF ceramic AVDD decoupling network within 5 mm of the AVDD pins (pins 1, 15, 34, 36) and a 100 nF HF-respond capacitor adjacent to the REFCAP pin. Route the SPI traces (SCLK, SDI, SDO, CONVST) over a continuous ground reference and avoid routing them under noisy digital or switching-power traces; place 33 ohm series resistors near the host to dampen reflections if the bus exceeds 50 mm.
Do not drive high-impedance sensor sources (>10 kohm) directly into the analog inputs - the input leakage current combined with mux-charge transients can introduce gain error. Place a 1 kohm series resistor and 1 nF X7R input capacitor at each AINx pin when interfacing with high-impedance sources. Additionally, ensure the REFEN pin configuration matches your reference strategy (REF-by-default = internal reference); leaving it floating defaults to internal but tying it low forces external reference mode, which is a common board-build bug.
When using multiple ADS8688IDBT devices in daisy-chain mode, accumulate the total SPI bus length and verify signal integrity at the maximum SCLK rate (the device supports up to ~50 MHz SPI). For chains of 4+ devices (>200 mm total bus length), insert a small ferrite or 22 ohm resistor at each SDO-to-SDI tap to isolate the stubs. Enable the internal SDO buffer strength via the device's CONFIG register if your host controller struggles with the default drive level on long buses.
At full 500 kSPS throughput across all 8 channels, the ADS8688IDBT dissipates approximately 65 mW from the 5 V AVDD supply - well within the TSSOP-38 thermal envelope (theta_JA ~ 75 C/W). However, ensure the AGND copper pour under the exposed pad region is unbroken and stitch-via'd to the analog ground plane to keep junction temperature rise below 10 C even at 85 C ambient. No external heatsink is required.
Informações de conformidade
RoHS and REACH compliant per TI product page. Lead-free (Pb-free) per the 'IDBT' ordering suffix. AEC-Q100 not explicitly stated on the TI product page - for AEC-Q100 qualified versions, consider the automotive-grade ADS8688 variants in the TI catalog. Halogen-free status not specified on TI product page.
