EPM9560RC240-3 - MAX 9000 CPLD 560 Macrocell | Altera
N.º da peça: EPM9560RC240-3 ✗ Fim de vida| Qtd. | Preço unitário | Total |
|---|---|---|
| 1 | $224.8 | $224,80 |
| 10 | $202.32 | $2.023,20 |
| 100 | $202.32 | $20.232,00 |
| 500 | $202.32 | $101.160,00 |
| 1.000 | $202.32 | $202.320,00 |
EPM9560RC240-3 Visão geral
A CPLD (Complex Programmable Logic Device) is a programmable logic IC built from non-volatile EEPROM cells that retain configuration without external memory. Within the logic IC hierarchy, a CPLD sits between simple PLDs (PAL/GAL) and FPGAs: it offers fewer logic resources than an FPGA but delivers deterministic, single-cycle timing and instant-on operation. The MAX 9000 family extends this architecture to FPGA-like densities using multiple Logic Array Blocks (LABs) interconnected by a fast, predictable routing matrix.
The EPM9560RC240-3 delivers 560 macrocells organized into 20 LABs, each containing 16 macrocells with individual product-term logic. Its 3 ns pin-to-pin delay (speed grade -3) supports synchronous interfaces up to approximately 150 MHz, while the 5 V core and I/O simplify direct interfacing to legacy TTL and CMOS buses without level shifters. The 240-pin RQFP package provides 192 I/O pins, enabling wide address/data bus decoding in a single device.
Architecturally, the MAX 9000 uses EEPROM-based configuration, giving the device instant-on capability and high immunity to single-event upsets compared with SRAM-based FPGAs. The multi-LAB structure with a programmable interconnect array (PIA) provides deterministic routing delays, which simplifies static timing analysis for critical control paths.
Typical applications include PCI and ISA bus bridging, telecommunications line-card control, industrial automation controllers, and legacy system glue logic where 5 V signaling and non-volatile configuration are required. The device is widely used as a replacement for discrete 74-series logic and older PAL devices in long-lifecycle industrial and telecom equipment.
When designing with the EPM9560RC240-3, note that the 5 V core draws significant quiescent current and requires adequate decoupling on every VCC pin. Because the part is obsolete, designers should verify availability and consider pin-compatible MAX 9000 speed-grade variants or migration to modern CPLDs for new designs.
This page synthesizes distributor availability, drop-in speed-grade alternatives, and practical design notes not found in the manufacturer datasheet, providing a single reference for engineers maintaining or sourcing this legacy CPLD.
Alternativas drop-in para EPM9560RC240-3 — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com EPM9560RC240-3 (mesmo formato e footprint) — diferindo em Package, RoHS Status, Usable Gates, Logic Array Blocks (LABs), Operating Temperature.
Ferramenta de comparação rápida — selecione peças alternativas para comparação lado a lado:
EPM9560RC240-2
✅ Drop-In✓ Em estoque
$180 / unidade
Ver ficha técnica →EPM9560RC240-1O
✅ Drop-In✓ Em estoque
$51.07 / unidade
Ver ficha técnica →EPM9560RC240-10
✅ Drop-In✓ Em estoque
Consulte o preço
Ver ficha técnica →EPM9560RC240-15
✅ Drop-In✓ Em estoque
$174.72 / unidade
Ver ficha técnica →EPM9560RC240-15YY
✅ Drop-In✓ Em estoque
$64.5 / unidade
Ver ficha técnica →EPM9560RC240-3 Classificações máximas e características elétricas
| Device Type | Complex Programmable Logic Device (CPLD) |
| Family | MAX 9000 |
| Macrocells | 560 |
| Usable Gates | 12000 |
| Logic Array Blocks (LABs) | 20 |
| Pin-to-Pin Propagation Delay | 3 ns (speed grade -3) |
| Supply Voltage (VCCINT) | 5 V |
| Supply Voltage (VCCIO) | 5 V |
| User I/O Pins | 192 |
| Encapsulamento | 240-pin RQFP (PowerQuad II) |
| Tipo de montagem | Surface Mount |
| Configuration Memory | EEPROM (non-volatile) |
| Faixa de temperatura de operação | 0C to +70C (commercial) |
Guia de Configuração de Pinos do EPM9560RC240-3 240-pin rqfp (powerquad ii)
Configuração de pinos para EPM9560RC240-3 (pacote 240-pin rqfp (powerquad ii)). Este CI digital inclui GPIO, interfaces de comunicação (UART, SPI, I2C) e pinos de alimentação. Consulte o datasheet do fabricante para funções alternativas dos pinos e opções de configuração. Essencial para projeto de sistemas embarcados e layout de PCB.
Nenhum dado detalhado de pinagem disponível para EPM9560RC240-3.
Consulte a ficha técnica para a configuração completa dos pinos.
Aplicações típicas
EPM9560RC240-3 é adequado para 6 aplicaçãos: PCI Bus Interface and Bridging, Telecommunications Line-Card Control, Industrial Automation Controllers, Legacy System Glue Logic Replacement, Test and Measurement Instrumentation, Military and Aerospace Legacy Upgrades.
PCI Bus Interface and Bridging
The EPM9560RC240-3 fits PCI bus interface and bridging because its 3 ns pin-to-pin delay and 192 user I/O pins meet the timing and signal-count demands of PCI target and bridge logic. With 560 macrocells, it implements address decoding, parity generation, and configuration-space registers in a single device. The 5 V I/O interfaces directly with legacy PCI and ISA buses without level shifters, reducing component count. Placed between the host bus and peripheral devices, it adds deterministic single-cycle logic delays that simplify static timing analysis. Unlike SRAM-based FPGAs, its EEPROM configuration is instant-on, so the bridge is active immediately after power-up with no configuration load time.
Recomendado
Telecommunications Line-Card Control
The EPM9560RC240-3 suits telecommunications line-card control because its 560 macrocells and 192 I/O pins handle channelized control, alarm monitoring, and bus arbitration on dense line cards. The 3 ns propagation delay supports synchronous state machines clocked at rates typical of TDM and SONET control interfaces, while the 5 V I/O matches legacy telecom backplane signaling. Its non-volatile EEPROM configuration ensures the card boots into a known logic state without an external configuration PROM, improving reliability in always-on central-office equipment. The deterministic routing of the MAX 9000 architecture lets designers bound worst-case control-path delays, which is essential for meeting telecom availability requirements.
Recomendado
Industrial Automation Controllers
The EPM9560RC240-3 is well suited to industrial automation controllers because its 5 V I/O interfaces directly with 5 V sensors, relays, and legacy PLC backplanes, and its 560 macrocells implement multi-axis sequencing and safety interlock logic. The 3 ns pin-to-pin delay supports fast encoder and limit-switch response, while the 192 I/O pins accommodate the high signal count of a machine-control board. EEPROM configuration gives instant-on operation after power interruption, which is critical on factory floors where recovery time matters. The device's wide commercial temperature range covers typical cabinet environments, and its deterministic timing simplifies validation of safety-related control paths.
Recomendado
Legacy System Glue Logic Replacement
The EPM9560RC240-3 replaces racks of discrete 74-series logic and older PAL/GAL devices in legacy systems, consolidating bus decoding, wait-state generation, and interrupt arbitration into one 240-pin RQFP device. Its 560 macrocells absorb dozens of SSI/MSI packages, reducing board area and power while improving reliability. Because the MAX 9000 family is EEPROM-based, the replacement logic is non-volatile and instant-on, matching the behavior of the discrete logic it replaces. The 5 V core and I/O preserve existing signal levels, so no redesign of surrounding circuitry is required. This makes the device a practical drop-in for sustaining long-lifecycle industrial, medical, and defense equipment.
Recomendado
Test and Measurement Instrumentation
The EPM9560RC240-3 fits test and measurement instrumentation because its 3 ns pin-to-pin delay supports high-speed trigger and timing generation, while 192 I/O pins handle wide data and control buses in a single device. The 560 macrocells implement pattern generators, event counters, and bus interfaces that would otherwise require multiple discrete ICs. Its 5 V I/O drives legacy instrument backplanes directly, and EEPROM configuration ensures the instrument is ready immediately at power-on without a configuration boot sequence. Deterministic MAX 9000 routing allows designers to bound trigger latency precisely, which is important for repeatable measurement results in automated test equipment.
Recomendado
Military and Aerospace Legacy Upgrades
The EPM9560RC240-3 is used in military and aerospace legacy upgrades because its EEPROM configuration is immune to the single-event upsets that can corrupt SRAM-based FPGAs, and its instant-on behavior suits systems that must resume operation immediately after power cycling. The 560 macrocells and 192 I/O pins support complex bus and control logic in a single 240-pin RQFP package, reducing board-level interconnects that are vulnerable to vibration and thermal cycling. The 5 V I/O matches legacy avionics and ground-equipment signaling. For long-lifecycle programs, pin-compatible MAX 9000 speed grades provide a second source when the -3 grade is unavailable.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para EPM9560RC240-3 — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | EPM9560RC240-2 | EPM9560RC240-1O | EPM9560RC240-10 | EPM9560RC240-15 |
|---|---|---|---|---|---|
| Package | 240-pin RQFP (PowerQuad II) | 240-pin RQFP - same | 240-pin RQFP - same | 240-pin RQFP - same | 240-pin RQFP - same |
| Brand | Altera | Altera | Altera | Altera | Altera |
| Macrocells | 560 | 560 | 560 | 560 | 560 |
| Usable Gates | 12000 | 12000 | 12000 | 12000 | 12000 |
| User I/O Pins | 192 | 192 | 192 | 192 | 192 |
| Supply Voltage | 5 V | 5 V | 5 V | 5 V | 5 V |
| Configuration Memory | EEPROM (non-volatile) | EEPROM (non-volatile) | EEPROM (non-volatile) | EEPROM (non-volatile) | EEPROM (non-volatile) |
| Lifecycle Status | Obsolete | Obsolete | Obsolete | Obsolete | Obsolete |
Principais diferenciais
- Fastest available MAX 9000 speed grade in 240-pin RQFP (vs EPM9560RC240-15)
- Higher speed than the -10 grade (vs EPM9560RC240-10)
- Non-volatile EEPROM configuration (vs EPM9560RC240-2)
Notas de projeto
Decouple every VCC pin of the EPM9560RC240-3 with a 0.1 uF ceramic capacitor placed as close to the pin as possible, plus at least one 10 uF bulk capacitor per power plane. The 5 V EEPROM-based MAX 9000 core draws significant transient current during logic switching; inadequate decoupling causes ground bounce and erratic operation. Estimated: at 5 V and a typical 150 mA dynamic current, the device dissipates about 0.75 W, so ensure the RQFP thermal pad and surrounding copper can remove that heat.
Route the 240-pin RQFP on a board with at least four layers so that a solid ground plane sits directly under the device. Keep high-speed I/O traces short and reference them to the ground plane to control impedance and crosstalk. Because the MAX 9000 uses a programmable interconnect array with deterministic delays, avoid unnecessary layer changes on critical control paths; each via adds inductance that can degrade the 3 ns timing margin of the -3 speed grade.
Do not assume a slower speed grade is a safe substitute without re-checking timing. Replacing EPM9560RC240-3 with EPM9560RC240-10 or -15 increases pin-to-pin delay from 3 ns to 10-15 ns, which can violate setup and hold times on fast buses. Also verify that the programmer and EDA toolchain support the MAX 9000 family, since modern Quartus releases have dropped support for these obsolete devices; legacy MAX+PLUS II software is typically required.
Informações de conformidade
No compliance data was present in the verified web data for EPM9560RC240-3. The device predates RoHS and is obsolete; confirm lead finish and RoHS status with the distributor before use in regulated markets.
