LM2901DG - Quad Comparator, 3-36 V, 14-SOIC | onsemi
N.º da peça: LM2901DG ✓ AtivoLM2901DG Visão geral
A comparator is an analog integrated circuit that compares two input voltages and changes its output state when one input becomes higher than the other. The LM2901 belongs to the comparator hierarchy within analog and mixed-signal semiconductors. Its four independent channels can evaluate separate thresholds, monitor multiple control signals, or implement sensing functions where a logic-compatible indication is preferable to a continuously amplified analog output.
Key features include a wide 3 V to 36 V single-supply operating range, dual-supply operation from ±1.5 V to ±18 V, and open-collector outputs compatible with CMOS and TTL. The maximum input bias current is 0.25 uA at 5 V, while typical low-level specifications include 25 nA input bias current, ±5 nA input offset current, and 130 mV low-output saturation voltage at 4 mA. These characteristics make the device appropriate for low-current threshold-detection circuits.
The four comparators share a common supply arrangement but operate independently, allowing separate reference and signal inputs for each channel. Open-collector outputs require an external pull-up resistor and can be wired for wired-AND behavior. The LM2901DG is identified as a CMOS, open-collector, TTL-compatible device, making it suitable for interfacing with both older TTL logic and CMOS control systems. Response time remains short enough for supervisory, sequencing, and discrete threshold applications.
Typical uses include industrial control-system threshold detection, automotive sensing interfaces, consumer equipment level supervision, and memory-device address or control comparisons. The 3 V minimum supply also permits operation from regulated 5 V rails, while the 36 V maximum supports higher-voltage industrial systems when suitable input protection is applied. Each open-collector output can directly drive a pull-up-connected digital input or relay driver stage.
For robust PCB design, place the pull-up resistor close to the output and maintain short, stable traces for sensitive threshold inputs. Account for input offset voltage when the decision point is critical, and prevent unused comparator inputs from floating. Confirm absolute maximum input and output ratings against the system rails before applying signals near the supply limits.
This page combines the LM2901DG operating envelope, drop-in comparison data, pin and package guidance, and application-oriented design notes. It also distinguishes the device from electrically similar quad comparators so engineers can assess supply range, output architecture, common-mode behavior, and timing before replacing an existing part.
Alternativas drop-in para LM2901DG — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com LM2901DG (mesmo formato e footprint) — diferindo em Comparator Type, Operating Temperature Range, Package.
LM2901D
✅ Drop-InConsulte o preço
Ver ficha técnica →LM2901DT
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
LM2901A
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
LM2901DG Classificações máximas e características elétricas
| Comparator Type | General Purpose |
| Number of Comparators | 4 |
| Single-Supply Voltage Range | 3 V to 36 V |
| Dual-Supply Voltage Range | ±1.5 V to ±18 V |
| Response Time | 1.3 us |
| Tipo de saída | Open Collector |
| Output Compatibility | CMOS, TTL |
| Corrente de alimentação | 1 mA |
| Maximum Input Bias Current | 0.25 uA at 5 V |
| Typical Low Input Bias Current | 25 nA |
| Typical Input Offset Current | ±5 nA |
| Typical Low Output Saturation Voltage | 130 mV at 4 mA |
| Faixa de temperatura de operação | -40°C to +105°C |
| Encapsulamento | 14-SOIC |
| Tipo de montagem | Surface Mount |
Guia de Configuração de Pinos do LM2901DG 14-soic
Configuração de pinos para LM2901DG (pacote 14-soic). Este componente analógico possui pinos de entrada, saída e alimentação. Consulte o datasheet do fabricante para configurações de offset null, compensação e pino de enable. Ideal para circuitos de condicionamento de sinal e amplificadores.
Nenhum dado detalhado de pinagem disponível para LM2901DG.
Consulte a ficha técnica para a configuração completa dos pinos.
Aplicações típicas
LM2901DG é adequado para 6 aplicaçãos: Industrial Threshold Detection, Automotive Sensing Interface, Memory Control and Level Sensing, Power-Supply Supervision, Consumer Equipment Level Detection, Industrial Control Signal Conditioning.
Industrial Threshold Detection
The LM2901DG fits industrial threshold-detection circuits because four independent channels can monitor separate signals within one 14-SOIC package. Its 3 V to 36 V single-supply range accommodates regulated 5 V control systems and higher-voltage industrial rails, while the typical 1.3 us response supports prompt supervision functions. Use each channel to compare a sensed voltage with a reference and drive an open-collector pull-up node. Account for input offset voltage when the switching threshold must remain precise, and apply external protection if field wiring can exceed the comparator input ratings.
Recomendado
Automotive Sensing Interface
The LM2901DG can translate low-level automotive sensor conditions into CMOS or TTL-compatible logic states using its open-collector outputs. The 3 V to 36 V supply range provides useful flexibility in 12 V vehicle electrical systems, and the four channels allow multiple thresholds to be evaluated independently. Pull-up the outputs to the logic rail used by a controller or indicator driver. Because automotive qualification status is not stated for this exact suffix, use the part only after confirming environmental, EMC, and quality requirements for the target vehicle program.
Recomendado
Memory Control and Level Sensing
The LM2901DG is suited to memory-related level sensing because it provides four differential channels, low typical input bias current of 25 nA, and a typical response time of 1.3 us. Each comparator can evaluate a memory-control signal against a reference and produce an open-collector indication for the surrounding logic. The open-collector architecture permits wired-AND implementations when multiple channels share a pull-up. Place the pull-up close to the output and keep sensitive input traces away from switching nodes to reduce false threshold transitions.
Recomendado
Power-Supply Supervision
The LM2901DG can supervise multiple power rails or control signals by comparing each input against an accurate reference and driving an open-collector output. Its 3 V to 36 V supply operation covers both low-voltage digital rails and higher-voltage systems, and the four-channel arrangement reduces component count. Use a resistor divider when the monitored voltage exceeds the input range, and select a pull-up voltage compatible with the supervisory logic. The typical 1.3 us response is sufficient for non-critical power-state detection rather than fast overcurrent protection.
Recomendado
Consumer Equipment Level Detection
The LM2901DG supports consumer-equipment level detection by providing four channels for comparing control voltages, sensor outputs, or interface signals against thresholds. Its low typical input bias current of 25 nA helps limit interference with high-impedance sensing circuits, while CMOS and TTL output compatibility simplifies connection to mixed logic families. The open-collector output requires a pull-up and can be used to combine multiple indications. Verify the input common-mode range at the chosen supply voltage and avoid leaving unused inputs floating.
Recomendado
Industrial Control Signal Conditioning
The LM2901DG can condition digital control signals by comparing a noisy or offset analog input with a reference and presenting an open-collector result to a controller. The 1.3 us typical response supports common sequencing and interlock functions, while the -40°C to +105°C rating suits industrial equipment. Add hysteresis with positive feedback when chatter near the threshold would be problematic. Keep reference components close to the relevant input pins and provide a defined pull-up rail for every output used by the controller.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para LM2901DG — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | LM2901D | LM2901DT | LM2901A |
|---|---|---|---|---|
| Package | 14-SOIC | 14-SOIC | 14-SOIC | 14-SOIC |
| Brand | onsemi | Texas Instruments | STMicroelectronics | 3PEAK |
| Number of Comparators | 4 | 4 | 4 | 4 |
Principais diferenciais
- Wide single-supply operating range (vs LM2901D)
- Four independent general-purpose channels (vs LM2901DT)
- Low typical input bias and offset currents (vs LM2901A)
Notas de projeto
Place the pull-up resistor for each used open-collector output close to the corresponding output pin and receiver. This minimizes the trace that can pick up noise between the comparator and the logic input. Route differential comparison inputs as a compact pair, keep them away from switching-power nodes, and place the reference divider or source near the appropriate input to reduce susceptibility to common-mode interference.
Do not connect an open-collector output to a supply rail without a pull-up resistor; the output transistor only pulls the node toward ground. Select a resistor that satisfies the receiver's input-current requirement while keeping the comparator's sink current within its specified operating range. Also connect every unused comparator input to a defined valid potential because floating inputs can oscillate and create unwanted supply-current changes.
Use positive-feedback hysteresis when the compared signals cross slowly or noise could cause repeated output transitions near the threshold. Choose the resistor network to create a controlled hysteresis band without increasing input bias effects or violating differential input limits. For high-impedance sensors, the typical 25 nA input bias current and ±5 nA typical input offset current should be included in the error budget.
Decouple the supply pins locally with a high-frequency ceramic capacitor and a bulk capacitor appropriate for the switching rate and trace impedance. Keep the supply return path short because the four channels share the same supply network. Although the listed operating range extends to 36 V, design transients, inductive spikes, and input excursions separately because absolute maximum ratings and common-mode limits are not interchangeable with the normal operating range.
Informações de conformidade
No definitive RoHS, REACH, lead-free, halogen-free, conflict-minerals, or AEC-Q100 statement was identified for the exact LM2901DG suffix. The comparator itself is an analog IC rather than an automotive-qualified product designation, so AEC-Q100 status requires separate qualification review.