LM2904AHYPT - Dual Low-Power Op Amp | STMicroelectronics
N.º da peça: LM2904AHYPT ✓ AtivoLM2904AHYPT Visão geral
A dual operational amplifier combines two independent amplifier sections in one package. In the broader semiconductor hierarchy, an operational amplifier is an analog integrated circuit used within the amplifier and signal-conditioning family. Each LM2904AHYPT section provides gain, filtering, buffering, or error amplification, while the common package can reduce board area and simplify component procurement for dual-channel circuits.
The principal advantages of this device are its low-power bipolar construction, dual-channel organization, and internally compensated architecture. Internal compensation removes the need for external frequency-compensation components in standard closed-loop operation. The 8-TSSOP package also offers a compact surface-mount format suitable for high-density analog and embedded-control boards. These characteristics make the device useful when a general-purpose amplifier must operate without external compensation networks.
Each amplifier section operates independently, allowing one channel to process a sensor signal while the other handles a control, feedback, or monitoring function. The LM2904 family is associated with approximately 100 dB open-loop gain, 1.1 MHz gain-bandwidth behavior, and 20 nA input bias current. Since the exact limits for every electrical condition are not listed on the product page, designers should confirm voltage, current, common-mode, and temperature limits against the manufacturer datasheet before final circuit sign-off.
Typical uses include low-frequency sensor conditioning, buffer stages, active filters, differential signal amplification, and general embedded analog interfaces. Because the package contains two amplifiers, the device can consolidate matching channels in instrumentation, industrial control, audio preamplification, and test-equipment input stages. TSSOP-8 placement is particularly useful when component count and routing density are important.
For layout, place each decoupling capacitor close to the corresponding supply pins and route input and feedback paths away from switching nodes. Confirm output swing, input common-mode range, stability, and load drive at the actual supply voltage. If a replacement uses the same footprint, verify that the enable, shutdown, slew-rate, and output-current characteristics remain compatible with the original design.
This page combines the manufacturer device identity, verified distributor descriptions, package information, family-level operating characteristics, and practical replacement guidance into an engineering-focused reference for evaluating the LM2904AHYPT.
Alternativas drop-in para LM2904AHYPT — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
LM2904HYPT
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
LM2904AYPT
✅ Drop-InConsulte o preço
Ver ficha técnica →LM2904AHYPT Classificações máximas e características elétricas
| Product Type | Dual operational amplifier |
| Number of Amplifier Channels | 2 channels |
| Circuit Type | 2-circuit single-ended |
| Technology | Bipolar |
| Power Class | Low-power |
| Frequency Compensation | Internally compensated |
| Encapsulamento | 8-TSSOP |
| Tipo de montagem | Surface mount |
| Open-Loop Gain | 100 dB |
| Gain-Bandwidth Product | 1.1 MHz |
| Input Bias Current | 20 nA |
| Número de pinos | 8 pins |
| Tipo de saída | Single-ended |
| Amplifier Independence | 2 independent amplifiers |
Configuração de pinos do LM2904AHYPT
| Pino 1 | OUT1 — Amplifier 1 output |
| Pino 2 | IN1- — Amplifier 1 inverting input |
| Pino 3 | IN1+ — Amplifier 1 non-inverting input |
| Pino 4 | V- — Negative supply connection |
| Pino 5 | IN2+ — Amplifier 2 non-inverting input |
| Pino 6 | IN2- — Amplifier 2 inverting input |
| Pino 7 | OUT2 — Amplifier 2 output |
| Pino 8 | V+ — Positive supply connection |
Aplicações típicas
LM2904AHYPT é adequado para 6 aplicaçãos: Industrial Sensor Signal Conditioning, Active Filtering and Control Loops, Audio Preamplification, Test and Measurement Buffering, Battery-Powered Embedded Interfaces, Power-Supply Feedback Monitoring.
Industrial Sensor Signal Conditioning
The LM2904AHYPT fits industrial sensor-conditioning circuits that require two independent amplifier channels in a compact footprint. One section can amplify a low-level transducer signal while the other handles monitoring, filtering, or error amplification. Its internally compensated bipolar architecture simplifies stable closed-loop implementation without external compensation parts, while the family characteristics of 100 dB open-loop gain and 1.1 MHz gain-bandwidth product support low-to-moderate frequency signal paths. Confirm the input common-mode range, output swing, offset voltage, and supply limits against the actual sensor excitation and industrial temperature requirements.
Recomendado
Active Filtering and Control Loops
The LM2904AHYPT is appropriate for active filters, integrators, and control loops that need independent gain stages near the controller. Its 1.1 MHz gain-bandwidth family characteristic provides useful bandwidth for low-frequency precision and process-control signals, while internal frequency compensation allows straightforward closed-loop layouts. Place the device close to the feedback components to minimize parasitic effects, and verify stability with the intended capacitor values and load. The two channels can implement a filter and an error amplifier in one 8-TSSOP package, reducing component count when two functions share the same supply and grounding arrangement.
Recomendado
Audio Preamplification
The LM2904AHYPT can serve in low-level audio preamplification and buffering circuits where two related channels are needed. One amplifier may condition the left input while the second handles the right input, and each section's internal compensation supports standard inverting or non-inverting feedback arrangements. The approximately 100 dB open-loop gain can provide useful loop gain, while the 1.1 MHz gain-bandwidth family rating is suitable for many audio-band signal paths. Check output drive, slew behavior, input bias current, and output swing for the selected feedback network before using it with low-impedance headphone or line-level loads.
Recomendado
Test and Measurement Buffering
The LM2904AHYPT is suitable for buffering instrumentation signals where source impedance must be isolated from a downstream ADC, comparator, or data-acquisition stage. Two independent sections can reduce loading in adjacent measurement channels, and the compact 8-TSSOP package leaves more PCB area for protection, precision resistors, and analog switches. The internal compensation supports stable closed-loop operation, and the family's 20 nA input bias current can be useful with high-impedance sources. Validate source impedance, input capacitance, output settling, noise, and common-mode limits across the complete measurement range.
Recomendado
Battery-Powered Embedded Interfaces
The LM2904AHYPT can be used in battery-powered embedded interfaces that require two low-power analog functions without adding a larger quad-amplifier package. It is useful for conditioning a sensor input and buffering a reference, threshold, or control signal around an embedded controller. Its low-power bipolar construction and dual-channel organization help consolidate analog functions, while the 8-TSSOP footprint supports compact surface-mount layouts. Review supply-current behavior over the complete input and output range, account for dropout behavior, and ensure the amplifier remains inside its common-mode range throughout battery discharge.
Recomendado
Power-Supply Feedback Monitoring
The LM2904AHYPT can supervise an intermediate supply rail by amplifying a divided feedback voltage and comparing or conditioning the result for an ADC or supervisor. The second section can buffer the feedback node, amplify a reference-related signal, or monitor another rail independently. Internal compensation makes the feedback network straightforward, and the dual 8-TSSOP implementation consolidates two monitoring functions in a compact area. Design the divider and compensation values for the required accuracy and bandwidth, check output saturation margins during fault conditions, and verify that the amplifier's supply range remains compatible with the monitored system.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para LM2904AHYPT — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | LM2904HYPT | LM2904AYPT |
|---|---|---|---|
| Package | 8-TSSOP | 8-TSSOP | 8-TSSOP |
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics |
| Amplifier Channels | 2 circuits | 2 circuits | 2 circuits |
| Technology | Low-power bipolar | Low-power bipolar | Low-power bipolar |
| Frequency Compensation | Internal | Internal | Internal |
| Special Ordering Grade | A-grade LM2904 ordering variant | H-grade LM2904 ordering variant | A-grade LM2904 ordering variant |
Principais diferenciais
- Two independent channels in a compact package (vs LM2904HYPT)
- Documented low-power bipolar implementation (vs LM2904AYPT)
- Internally compensated dual-amplifier design (vs LM2904HYPT)
Notas de projeto
Place the supply bypass capacitor immediately between pins 8 and 4, with a short return path to the ground plane. Keep the amplifier inputs and feedback components away from the capacitor and from switching-regulator power paths. The TSSOP-8 footprint supports dense placement, but short feedback loops remain important for stable operation and predictable transient response.
Route both amplifier channels independently and avoid sharing narrow feedback traces between them. Maintain a continuous ground reference beneath and around the package, and connect each bypass capacitor directly to the relevant supply and ground pins. If the LM2904AHYPT follows a switching converter, keep its input and output networks away from the switching node and provide filtering appropriate to the required noise margin.
Do not assume that every LM2904 ordering suffix has identical offset, bias-current, temperature, or qualification limits. Before substituting LM2904HYPT or LM2904AYPT, compare the exact ordering table, supply range, common-mode range, output swing, and package drawing. Also confirm that the TSSOP lead pitch matches the PCB footprint; an 8-TSSOP footprint cannot be treated as an 8-SOIC footprint.
Check closed-loop stability with the intended feedback network, load capacitance, source impedance, and external capacitance at the input and output. Add isolation resistors near the op-amp pins when driving capacitive loads or sampling nodes. The internal compensation simplifies ordinary feedback configurations, but it does not eliminate the need for application-level stability checks.
Informações de conformidade
Compliance status was not stated on the manufacturer product page or in the distributor records.