PCM56P-L - 16-Bit Audio DAC | Texas Instruments
N.º da peça: PCM56P-L ✓ Ativo| Qtd. | Preço unitário | Total |
|---|---|---|
| 1 | $0 | $0,00 |
| 10 | $0 | $0,00 |
| 100 | $0 | $0,00 |
| 500 | $0 | $0,00 |
| 1.000 | $0 | $0,00 |
PCM56P-L Visão geral
A digital-to-analog converter is an integrated circuit that converts a digital audio code stream into a proportional analog voltage or current. The PCM56 belongs to the DAC family within the broader ADC/DAC and signal-conversion hierarchy. Its internal architecture combines a stable low-noise zener voltage reference, high-speed current switches, a resistor ladder network, and a fast-settling low-noise output operational amplifier on one monolithic chip.
The series datasheet identifies no external components as required for the converter core, while factory trimming and testing support the critical audio specifications. The device is intended for applications where low distortion, stable reference behavior, and controlled settling are important. The PCM56P-L designation identifies the -L grade, so designers should use the manufacturer ordering table and datasheet grade limits when comparing it with other PCM56 variants.
Typical uses include CD-player audio paths, digital audio decoding systems, instrumentation, waveform generation, and other audio DAC circuits that accept serial digital data. Dual positive and negative supplies are required by the series architecture, and the analog output stage should be evaluated against the selected load, grounding, decoupling, and signal-chain requirements.
The principal design consideration is ensuring adequate supply headroom and clean reference behavior. Follow the datasheet's recommended decoupling and layout practices, observe the specified supply range, and account for settling time when driving subsequent analog stages. The PCM56 is an audio-focused converter rather than a generic waveform DAC, so its performance claims should be evaluated at the signal levels, frequencies, and loads relevant to the intended audio path.
This page combines the verified manufacturer and distributor descriptions, identifies the important architecture and orderable package facts, and separates verified data from parameters that require design-specific confirmation. It is intended to support sourcing, comparison, and first-pass engineering review without replacing the complete manufacturer datasheet.
Alternativas drop-in para PCM56P-L — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com PCM56P-L (mesmo formato e footprint) — diferindo em Package, Product Type, Mounting Type, Resolution, Data Interface.
Ferramenta de comparação rápida — selecione peças alternativas para comparação lado a lado:
PCM56P-K
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
PCM56P-J
✅ Drop-In✓ Em estoque
Consulte o preço
Ver ficha técnica →PCM56P
✅ Drop-In✓ Em estoque
Consulte o preço
Ver ficha técnica →PCM56U
✅ Drop-In✓ Em estoque
Consulte o preço
Ver ficha técnica →PCM61P-K
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
PCM56P-L Classificações máximas e características elétricas
| Product Type | Series-input 16-bit monolithic digital-to-analog converter |
| Resolução | 16 bit |
| Dynamic Range | 96 dB |
| Maximum Total Harmonic Distortion | -92 dB at full-scale input, K grade |
| Total Harmonic Distortion at -20 dB Input | -74 dB maximum, K grade |
| Monotonicity | 15-bit typical, 0.001% of FSR typical differential linearity error |
| Supply Voltage Range | ±5 V to ±12 V |
| Power Supply Configuration | Dual positive and negative supplies |
| Reference | Internal stable low-noise zener voltage reference |
| Architecture | Internal current switches, resistor ladder network, and output operational amplifier |
| External Components | No external components required |
| Encapsulamento | 16-pin molded plastic DIP |
| Package Pin Count | 16 pin |
| Tipo de montagem | Through-hole |
| Operating Life Testing | Passed simultaneous high-pressure, high-temperature, and high-humidity life tests |
Guia de Configuração de Pinos do PCM56P-L 16 pin
Configuração de pinos para PCM56P-L (pacote 16 pin). Este componente analógico possui pinos de entrada, saída e alimentação. Consulte o datasheet do fabricante para configurações de offset null, compensação e pino de enable. Ideal para circuitos de condicionamento de sinal e amplificadores.
Nenhum dado detalhado de pinagem disponível para PCM56P-L.
Consulte a ficha técnica para a configuração completa dos pinos.
Aplicações típicas
PCM56P-L é adequado para 6 aplicaçãos: CD-Player Audio DAC, Digital Audio Decoder, High-Fidelity Audio Measurement, Instrumentation Signal Generator, Digital Audio Development Platform, Audio Processing and Amplifier Input.
CD-Player Audio DAC
PCM56P-L fits a CD-player reconstruction path because it converts serial digital audio data with 16-bit resolution and a 96 dB dynamic-range figure identified in the PCM56 series material. Its internal reference, current switches, resistor ladder, and output amplifier make the converter core self-contained. The designer still needs to confirm serial-interface timing, output filtering, dual ±5 V to ±12 V supplies, and the analog load before layout release. The -L grade should be selected only when its verified distortion limits satisfy the system requirement.
Recomendado
Digital Audio Decoder
The PCM56P-L can serve as the analog reconstruction element in a digital audio decoder when the source supplies a compatible serial data stream. Its 16-bit architecture and audio-oriented distortion and dynamic-range figures help preserve the coded signal during conversion. Dual supplies provide the required operating range of ±5 V to ±12 V, but the decoder must include appropriate decoupling and an output reconstruction filter. Verify the exact clock and data protocol against the PCM56 datasheet rather than assuming compatibility with every I2S or PCM interface.
Recomendado
High-Fidelity Audio Measurement
PCM56P-L is suitable for laboratory audio measurement and signal-generation systems where the selected grade's verified THD, dynamic range, and settling behavior are adequate for the test bandwidth. The integrated reference and monolithic converter structure simplify the analog signal chain, while the 16-bit resolution supports detailed audio waveform representation. For precision measurements, calibrate the external clock, load, output filtering, and measurement bandwidth, and compare the -L grade limits with the instrument's noise floor and distortion requirements.
Recomendado
Instrumentation Signal Generator
The PCM56P-L can be evaluated as the digital-to-analog stage in an instrumentation signal generator when its serial input, dual-supply requirement, and settling performance fit the required waveform bandwidth. The 16-bit resolution provides a precise digital code basis, while the internal reference helps simplify calibration. The converter is audio-focused, so applications requiring high-frequency waveform fidelity, wide output swing, or unusual load drive should compare the complete datasheet limits before choosing it. External filtering and output buffering are likely needed.
Recomendado
Digital Audio Development Platform
PCM56P-L is useful in a digital audio development platform because it exposes a dedicated serial-input DAC function in a through-hole 16-pin DIP package. The DIP format simplifies prototyping, inspection, and replacement compared with a fine-pitch surface-mount package. Engineers can use it to evaluate analog reconstruction behavior, distortion, and output filtering in a controlled prototype. Before committing to production, confirm lifecycle status, sourcing, package availability, and any required grade-specific screening.
Recomendado
Audio Processing and Amplifier Input
PCM56P-L can feed an audio processing or amplifier-input stage when the downstream circuit requires a clean analog voltage derived from a digital source. The converter's internal output amplifier reduces the need for a basic output buffer, but the final load and filtering network remain design-specific. Keep the analog output path short, maintain the specified supply rails, and avoid adding excessive loading that could degrade settling or distortion. Confirm the output polarity and voltage range in the complete datasheet before connecting the stage.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para PCM56P-L — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | PCM56P-K | PCM56P-J | PCM56P | PCM56U | PCM61P-K |
|---|---|---|---|---|---|---|
| Product Type | Series-input 16-bit monolithic DAC | PCM56 family audio DAC | PCM56 family audio DAC | PCM56 family audio DAC | PCM56 family audio DAC | PCM61 family audio DAC |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
Principais diferenciais
- Self-contained monolithic audio DAC architecture (vs PCM56P-K)
- 16-bit resolution with 96 dB dynamic range (vs PCM56P-J)
- Through-hole 16-pin DIP package (vs PCM61P-K)
Notas de projeto
Use the PCM56 dual positive and negative supply arrangement exactly as specified in the manufacturer datasheet. The verified series description gives an operating range of ±5 V to ±12 V. Place the required supply-decoupling capacitors close to the converter pins and keep the return-current paths short; excessive supply impedance can reduce settling performance and increase distortion. Confirm the absolute maximum ratings and startup sequence from the datasheet before applying rails.
Route serial data and clock traces away from the analog output and reference-related paths. A DIP prototype can be forgiving, but a production PCB still needs a compact analog section, controlled return paths, and separated digital and analog regions. Keep the PCM56P-L output network close to the device and verify the final filter and load because external capacitance can alter settling. Use the manufacturer pin configuration and application recommendations as the source of truth.
Check data and clock timing against the PCM56 serial-interface requirements before connecting a digital audio source. The PCM56 family is audio-focused and the verified material does not establish universal compatibility with every I2S or PCM format. Keep the digital clock clean, provide a stable source clock, and measure settling at the intended output bandwidth. If the downstream circuit is sensitive to aliasing, include the appropriate reconstruction filter and verify its response with the complete signal chain.
The verified datasheet excerpt states that power dissipation with ±5 V supplies is typically less than the device's specified limits, but the complete numeric thermal data is not included in the supplied snippets. Do not estimate thermal performance from the package name alone. Use the manufacturer dissipation and maximum-temperature specifications, provide normal airflow where required, and keep the analog output load within the verified operating conditions.
Informações de conformidade
The supplied verified data identifies the package and operating-life testing but does not explicitly state RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status. Compliance must be confirmed using the current TI material declaration or distributor compliance record.
