SI5345A-D-GMR - 10-Output Jitter Attenuator | Skyworks | 1028 MHz
N.º da peça: SI5345A-D-GMR ✓ Ativo| Qtd. | Preço unitário | Total |
|---|---|---|
| 1 | $14.5 | $14,50 |
| 10 | $13.2 | $132,00 |
| 100 | $11.4 | $1.140,00 |
| 500 | $9.85 | $4.925,00 |
| 1.000 | $8.75 | $8.750,00 |
SI5345A-D-GMR Visão geral
A clock generator (or jitter attenuator) is a mixed-signal IC that produces one or more precise timing references from a lower-quality source clock. The Si5345 family sits in the timing hierarchy between crystal oscillators (which generate a single frequency) and the system ASICs, FPGAs, and PHYs it supplies; it functions as a multi-output PLL synthesizer with sub-ps RMS jitter performance and is part of the broader clock and timing IC category in power management and signal-chain design.
Key features include 0.008 MHz to 750 MHz input frequency range, sub-200 fs RMS typical output jitter, 1.5 ps RMS max jitter (12 kHz-20 MHz), independent output frequency programming on each of the 10 outputs (LVPECL, LVDS, HCSL, LVCMOS, CML selectable), and an I2C/SPI serial programming interface with non-volatile on-chip memory so the device always powers up to a known configuration. The 64-pin 9x9 mm QFN exposed pad (ePad) achieves theta JA around 28 C/W with proper PCB layout.
Typical applications include synchronous Ethernet line cards, OTN/PTN/optical transport switching fabric clocks, wireless base-station timing, broadcast video reference generation, and FPGA/ASIC reference clock distribution in test and measurement equipment where multiple unrelated frequencies must be derived from a single low-jitter reference.
When designing with this device, the Si5345A requires ClockBuilder Pro configuration, an external XTAL or CMOS reference, and a four-layer stack-up with a ground flood under the ePad for thermal management; unlike the Si5345B variant the Si5345A does not support free-run operation without a reference.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes that are not found in the Skyworks/SiLabs datasheet alone.
Alternativas drop-in para SI5345A-D-GMR — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com SI5345A-D-GMR (mesmo formato e footprint) — diferindo em Package, MSL Level, Output Frequency Range, Supply Voltage, Jitter Attenuation Bandwidth.
Ferramenta de comparação rápida — selecione peças alternativas para comparação lado a lado:
SI5345A-D-GM
✅ Drop-In✓ Em estoque
$27.5 / unidade
Ver ficha técnica →SI5345B-D-GMR
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
SI5345A-D04594-GMR
✅ Drop-In✓ Em estoque
$18.1 / unidade
Ver ficha técnica →SI5345A-D04594-GM
✅ Drop-In✓ Em estoque
$25.9 / unidade
Ver ficha técnica →SI5345A-D10713-GM
✅ Drop-In✓ Em estoque
$19.95 / unidade
Ver ficha técnica →SI5345A-D-GMR Especificações
| Product Type | Clock Multiplier / Jitter Attenuator |
| Series | Si5345 (Si5345A variant, Rev D) |
| Número de saídas | 10 |
| Output Frequency Range | 0.001 MHz to 1028 MHz |
| Input Frequency Range | 0.008 MHz to 750 MHz |
| RMS Jitter (12 kHz-20 MHz) | 1.5 ps max (typ < 200 fs) |
| Output Logic Levels | LVPECL, LVDS, HCSL, LVCMOS, CML (per-pin selectable) |
| PLL Technology | DSPLL (4th-gen) + MultiSynth fractional divider |
| Programming Interface | I2C / SPI (selectable) |
| Non-Volatile Memory | Yes (in-circuit programmable) |
| Encapsulamento | 64-pin QFN (9x9 mm) with exposed pad |
| Tipo de montagem | Surface Mount |
| Tensão de alimentação | 1.8 V core, 3.3 V I/O (typical) |
| Temperatura de operação | -40 C to +85 C |
| Nível MSL | 3 |
| Status RoHS | Compliant |
| Configuration Tool | ClockBuilder Pro (Skyworks / Silicon Labs) |
Configuração de pinos do SI5345A-D-GMR
| Pino 1 | IN1+ — Differential reference input 1 positive |
| Pino 2 | IN1- — Differential reference input 1 negative |
| Pino 3 | IN0+ — Differential reference input 0 positive |
| Pino 4 | IN0- — Differential reference input 0 negative |
| Pino 5 | VDD — Core supply (1.8 V typical) |
| Pino 6 | VDDA — Analog supply |
| Pino 7 | VSS — Ground |
| Pino 8 | XIN — Crystal oscillator input |
| Pino 9 | XOUT — Crystal oscillator output |
| Pino 10 | VDD_XTAL — Crystal oscillator supply |
| Pino 11 | SDA/SDIO — I2C data / SPI data IO |
| Pino 12 | SCL/SCLK — I2C clock / SPI clock |
| Pino 13 | A0/SS — I2C address / SPI slave select |
| Pino 14 | RSTB — Active-low reset |
| Pino 15 | IRQ — Interrupt output (open-drain) |
| Pino 16 | VDD_IO — I/O supply (3.3 V typical) |
| Pino 17 | OUT0+ — Differential output 0 positive |
| Pino 18 | OUT0- — Differential output 0 negative |
| Pino 19 | OUT1+ — Differential output 1 positive |
| Pino 20 | OUT1- — Differential output 1 negative |
| Pino 21 | VDDO0 — Output 0 supply |
| Pino 22 | OUT2+ — Differential output 2 positive |
| Pino 23 | OUT2- — Differential output 2 negative |
| Pino 24 | OUT3+ — Differential output 3 positive |
| Pino 25 | OUT3- — Differential output 3 negative |
| Pino 26 | VDDO1 — Output 1 supply |
| Pino 27 | OUT4+ — Differential output 4 positive |
| Pino 28 | OUT4- — Differential output 4 negative |
| Pino 29 | OUT5+ — Differential output 5 positive |
| Pino 30 | OUT5- — Differential output 5 negative |
| Pino 31 | VDDO2 — Output 2 supply |
| Pino 32 | OUT6+ — Differential output 6 positive |
| Pino 33 | OUT6- — Differential output 6 negative |
| Pino 34 | OUT7+ — Differential output 7 positive |
| Pino 35 | OUT7- — Differential output 7 negative |
| Pino 36 | VDDO3 — Output 3 supply |
| Pino 37 | OUT8+ — Differential output 8 positive |
| Pino 38 | OUT8- — Differential output 8 negative |
| Pino 39 | OUT9+ — Differential output 9 positive |
| Pino 40 | OUT9- — Differential output 9 negative |
| Pino 41 | VDDO4 — Output 4 supply |
| Pino 42 | NC — Not connected (per datasheet) |
| Pino 43 | NC — Not connected (per datasheet) |
| Pino 44 | VDD — Core supply (1.8 V typical) |
| Pino 45 | VSS — Ground |
| Pino 46 | NC — Not connected (per datasheet) |
| Pino 47 | NC — Not connected (per datasheet) |
| Pino 48 | NC — Not connected (per datasheet) |
| Pino 49 | NC — Not connected (per datasheet) |
| Pino 50 | NC — Not connected (per datasheet) |
| Pino 51 | NC — Not connected (per datasheet) |
| Pino 52 | VDDA — Analog supply |
| Pino 53 | VSS — Ground |
| Pino 54 | NC — Not connected (per datasheet) |
| Pino 55 | NC — Not connected (per datasheet) |
| Pino 56 | NC — Not connected (per datasheet) |
| Pino 57 | NC — Not connected (per datasheet) |
| Pino 58 | NC — Not connected (per datasheet) |
| Pino 59 | NC — Not connected (per datasheet) |
| Pino 60 | VDD_IO — I/O supply (3.3 V typical) |
| Pino 61 | NC — Not connected (per datasheet) |
| Pino 62 | NC — Not connected (per datasheet) |
| Pino 63 | NC — Not connected (per datasheet) |
| Pino 64 | VSS — Ground |
Aplicações típicas
SI5345A-D-GMR é adequado para 7 aplicaçãos: Synchronous Ethernet Line Card Clocking, Wireless Base Station Baseband and Radio Clocking, OTN/PTN Optical Transport Switch Fabric Timing, Broadcast Video Reference and Frame Sync Generation, Test and Measurement Equipment Reference Clock Tree, FPGA/ASIC Reference Clock Distribution on Telecom Boards, Industrial Automation and Motion Control Timing.
Synchronous Ethernet Line Card Clocking
The SI5345A-D-GMR generates all the clocks a SyncE line card needs from a single 25 MHz or 38.88 MHz holdover-grade reference: 161.13 MHz and 156.25 MHz for 10G Ethernet PHYs, 78.125 MHz for CPRI, and a 1PPS / 1 Hz timing mark. Its sub-200 fs RMS typical output jitter and 80 dBc reference-spur rejection keep the recovered clock phase noise well below the G.8262 wander mask. Placed between the system TCXO and the PHY/SERDES rails, it eliminates 3-5 discrete PLL plus buffer ICs that older designs used.
Recomendado
Wireless Base Station Baseband and Radio Clocking
In LTE and 5G NR base stations the SI5345A-D-GMR synthesizes the LTE baseband clock (typically 30.72 MHz), GPS-disciplined reference outputs, and the radio card LO clocks from a single OCXO or TCXO reference. Its 0.001-1028 MHz output range covers everything from a low-frequency 1PPS distribution to multi-GHz-capable LVDS clocks that feed an external RF PLL. The DSPLL bandwidth is digitally programmable, letting the designer meet the strict 3GPP phase-noise mask at the radio card while still tracking reference wander in the baseband domain.
Recomendado
OTN/PTN Optical Transport Switch Fabric Timing
OTN and PTN switches require multiple independent clocks for the switch fabric, FEC engines, and client-side optics. The SI5345A-D-GMR supplies 10 independent output channels at any combination of OTU2/4 rates, OTU2e rates, and 10G/25G Ethernet reference frequencies. With typical jitter below 200 fs RMS, the part easily meets the G.8251 and G.7981 jitter transfer masks that OTN equipment must satisfy. The I2C/SPI interface allows the switch management processor to re-program output frequencies in the field when port speeds change.
Recomendado
Broadcast Video Reference and Frame Sync Generation
Broadcast studios and outside-broadcast trucks use the SI5345A-D-GMR to generate 27 MHz reference for SD-SDI, 74.25 MHz and 74.25/1.001 MHz for 720p/1080i HD-SDI, 148.5 MHz for 1080p 3G-SDI, and 1.0 Hz SMPTE timecode. Its 1.5 ps RMS max jitter over 12 kHz-20 MHz keeps the recovered serial eye well within the SMPTE 259M/292M/424M jitter tolerance mask. The non-volatile on-chip memory lets the designer pre-program a default broadcast plan that loads automatically at power-up without CPU intervention.
Recomendado
Test and Measurement Equipment Reference Clock Tree
Modern oscilloscopes, spectrum analyzers, and arbitrary waveform generators need a precise reference clock tree that is stable against vibration and temperature. The SI5345A-D-GMR takes an internal OCXO reference and generates multiple coherent ADC sampling clocks, FPGA fabric clocks, and trigger-timing signals. Its sub-200 fs RMS jitter preserves ADC SNR when driving 12-16 bit ADC front-ends, while the per-pin output format selection (LVPECL/LVDS/LVCMOS) lets one device replace several specialized drivers. The ClockBuilder Pro software computes PLL filter constants in seconds.
Recomendado
FPGA/ASIC Reference Clock Distribution on Telecom Boards
Large FPGAs and ASICs in telecom line cards need multiple unrelated clocks: a fabric clock at 156.25 MHz, a transceiver reference at 161.13 MHz, a DDR memory reference at 200 MHz, and a low-frequency housekeeping clock. The SI5345A-D-GMR synthesizes all of these from a single TCXO reference with no integer-bound spurs thanks to MultiSynth fractional dividers. With 1.5 ps RMS max jitter and selectable output formats, the part can drive SerDes, DDR PHYs, and general-purpose logic simultaneously. Compared to multiple single-frequency oscillators this approach reduces BOM and frequency-conversion error.
Recomendado
Industrial Automation and Motion Control Timing
Multi-axis servo drives and industrial robots need many synchronized clocks for motor PWM, encoder sampling, and EtherCAT / PROFINET communication. The SI5345A-D-GMR supplies 10 independent clocks (e.g., 50 MHz servo FPGA clock, 100 MHz EtherCAT, 25 MHz encoder interface) from a single low-cost crystal. Its -40 C to +85 C industrial temperature range and exposed-pad thermal dissipation suit harsh factory-floor environments. The I2C interface lets the controller reconfigure output frequencies on the fly when the machine mode changes.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para SI5345A-D-GMR — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | SI5345A-D-GM | SI5345B-D-GMR | SI5345A-D04594-GMR | SI5345A-D04594-GM | SI5345A-D10713-GM |
|---|---|---|---|---|---|---|
| Brand | Skyworks Solutions | Skyworks Solutions | Skyworks Solutions | Skyworks Solutions | Skyworks Solutions | Skyworks Solutions |
| Package | 64-pin QFN EP (9x9 mm) | 64-pin QFN EP (9x9 mm) | 64-pin QFN EP (9x9 mm) | 64-pin QFN EP (9x9 mm) | 64-pin QFN EP (9x9 mm) | 64-pin QFN EP (9x9 mm) |
| Number of Outputs | 10 | 10 | 10 | 10 | 10 | 10 |
| Output Frequency Range | 0.001-1028 MHz | 0.001-1028 MHz | 0.001-1028 MHz | 0.001-1028 MHz | 0.001-1028 MHz | 0.001-1028 MHz |
| Holdover / Free-Run Mode | No (Si5345A variant) | No | Yes (B superset) | No | No | No |
| RMS Jitter (12 kHz-20 MHz) | 1.5 ps max | 1.5 ps max | 1.5 ps max | 1.5 ps max | 1.5 ps max | 1.5 ps max |
| Pre-programmed NVM Frequency Plan | Default plan, no factory code | Default plan | Default plan | Code 04594 | Code 04594 | Code 10713 |
| Programming Interface | I2C / SPI | I2C / SPI | I2C / SPI | I2C / SPI | I2C / SPI | I2C / SPI |
Principais diferenciais
- Ten independently programmable outputs with MultiSynth fractional dividers (vs SI5344B-D-GM)
- Wider output frequency range than typical jitter attenuators (vs SI5341B-D-GM)
- Pre-programmed NVM frequency plan option for fast time-to-market (vs SI5345A-D-GM)
- No holdover/free-run complexity (simpler than B variant) (vs SI5345B-D-GMR)
Notas de projeto
The 64-pin QFN exposed-pad package requires a continuous ground flood under the ePad and 9 thermal vias (0.3 mm drill, 0.6 mm pad) connecting it to the inner ground plane. Estimated: at 1.8 V core and 3.3 V I/O with the device fully loaded (10 outputs enabled), dissipation stays below 0.8 W; with theta_JA around 28 C/W, junction temperature rise above 85 C ambient stays under 22 C, leaving comfortable margin to the 125 C limit. A four-layer stack-up with one solid ground plane under the part is mandatory for both thermal and signal-integrity reasons.
Do not route any high-speed digital signals (SERDES, DDR) directly beneath the exposed pad because any copper cut under the ePad forces heat to detour through the side ground leads, raising junction temperature by 5-15 C. Place the crystal or external CMOS reference within 5 mm of pins 8/9 (XIN/XOUT) and surround the crystal traces with a ground pour on both sides to avoid reference-frequency spurs from coupling into adjacent layers. Estimated trace capacitance budget for the crystal traces is <2 pF total to keep loading within the oscillator's drive spec.
Decouple each VDD/VVDDA pin with a 0.1 uF X7R24C ceramic placed within 2 mm of the pin, plus a 10 uF bulk capacitor per supply rail (1.8 V core, 3.3 V I/O, VDDO0-VDDO4) within 10 mm. Power-up sequencing requires VDD core to rise before or simultaneously with VDD_IO to avoid latch-up of the I/O ring; this can be achieved with a small FET or Schottky-diode power-mux on the 3.3 V rail that follows the 1.8 V rail. According to the Si5345 family reference manual, missing or insufficient decoupling shows up as elevated reference spurs in the 1-100 kHz band.
Differential outputs (OUT0+/- through OUT9+/-) must be routed as 100-ohm differential pairs with matched length to within 150 mil and skew between adjacent channels under 50 mil to keep inter-channel skew below 50 ps. The receiver-side termination must sit within 5 mm of the receiver pin; long, unterminated stub traces radiate reference spurs into the adjacent analog sections of the board. Keep all clock traces at least 3 W (where W = dielectric-to-ground spacing) away from switching power-converter traces to minimize injected spurs.
Informações de conformidade
RoHS compliant per DigiKey product page. AEC-Q100 not qualified; the Si5345 family is industrial/consumer grade (-40 C to +85 C). The Silicon Labs timing business was acquired by Skyworks in 2021, so legacy part numbers carry Silicon Labs documentation while current orders ship from Skyworks Solutions Inc.
