Управление питанием
Подкатегории
Товары (2819)
MIC47100YML-TR - 1A Low-VIN LDO Regulator | Microchip | 8-MLF
The Microchip Technology MIC47100YML-TR is a high-speed, low-VIN low-dropout (LDO) linear regulator that delivers up to 1A of output current from a 1V to 3.6V input rail, packaged in an 8-pin 2 mm × 2 mm MLF® (also marketed as DFN) with an exposed pad for thermal dissipation. An LDO (low-dropout) linear regulator is a type of voltage regulator that maintains a stable output voltage even when the input voltage is very close to the output voltage. LDOs sit within the broader hierarchy of linear regulators, themselves a sub-family of voltage regulators and ultimately part of the power management IC (PMIC) category. Because they burn the excess VIN−VOUT as heat, LDOs add no switching noise to the rail - making them the default choice for point-of-load supplies that follow a switching pre-regulator. Key features of the MIC47100 include an adjustable output range from 0.8V to 2V (the YML variant) plus fixed-voltage members, an ultra-low 80 mV typical dropout at full 1A load, and stability with only a 1 µF ceramic output capacitor - eliminating the bulky tantalum or electrolytic capacitors required by older LDOs. The part also integrates a single active-high enable pin for sequenced power-up and a "zero off-mode-current" shutdown state, allowing downstream battery savings in portable systems. Architecturally, the MIC47100 uses a high-bandwidth pass element and a precision bandgap reference to deliver fast transient response to load steps, which is critical for powering modern FPGAs, ASICs, and high-speed digital logic. The wide VIN range (down to 1V) lets the part regulate point-of-load rails directly from a 1.2V or 1.5V intermediate bus, removing an extra regulator stage. Typical applications include FPGA/ASIC core and I/O voltage rails in networking switches, DDR memory termination supplies, portable/handheld point-of-load regulation, industrial single-board computers, and any board that needs a clean, low-noise 1A rail generated from an existing low-voltage bus. When designing with the MIC47100YML-TR, keep input-to-output headroom below 3.6V and place the 1 µF ceramic input/output capacitors as close to the IC as possible. The exposed pad must be soldered to a sufficient ground copper pour to keep junction temperature within the -40 °C to +125 °C operating range. This page synthesizes distributor pricing, same-brand and cross-brand alternatives, and practical design notes not found in the manufacturer datasheet, giving engineers an actionable reference for selecting the MIC47100YML-TR.
MIC5206-3.0YM5-TR - 150mA 3.0V Fixed LDO | Microchip Technology
The Microchip Technology MIC5206-3.0YM5-TR is a 150 mA fixed-output 3.0 V low-dropout (LDO) linear regulator housed in a 5-pin SOT-23-5 surface-mount package. It features an ultra-low dropout voltage of 17 mV (typical) at light loads and 165 mV at 150 mA, with 600 µA (typical) ground current at 100 mA output, and ±1 % initial output voltage accuracy. The -3.0YM5-TR variant is the fixed 3.0 V output ordering code in the MIC5206 series, supplied on a 3,000-piece tape-and-reel. An LDO (Low-Dropout) linear regulator is a type of voltage regulator that maintains a stable output voltage even when the input voltage is very close to the output voltage, eliminating the need for a step-down switching pre-converter in many low-headroom applications. In the broader system hierarchy, the LDO sits inside the linear regulator class, which itself belongs to the voltage regulator family and ultimately the power management IC (PMIC) category. LDOs are favored over switching converters where low noise, small board area, and fast transient response outweigh efficiency concerns. Key features of the MIC5206-3.0YM5-TR include very low ground current, a logic-compatible active-high enable/shutdown input, an internal undervoltage monitor, thermal shutdown, and current-limit protection. The device requires only 1 µF of output capacitance for stability when the ESR is in the recommended range, simplifying BOM and layout. The SOT-23-5 footprint exposes a tab tied to ground for improved thermal dissipation in a compact package. Architecturally, the MIC5206 uses a PNP pass transistor topology, which gives it the low-dropout characteristic that older NPN regulators could not achieve. The reference, error amplifier, and feedback network are trimmed at the factory to deliver better than 1 % initial accuracy on the fixed -3.0 V output code, and a flag output indicates an undervoltage condition for system monitoring. Typical applications include powering microcontroller core rails, real-time-clock (RTC) backup supplies, post-regulation after a switching converter, USB peripheral power, and battery-powered handheld electronics. The enable pin allows the host microcontroller to shut the regulator down for sleep-mode current savings, while the undervoltage flag supplies reset signaling. Compared with a buck converter, the MIC5206-3.0YM5-TR adds no switching noise to the rail but does dissipate (VIN - 3.0 V) × IOUT as heat, so reserve thermal headroom in the layout. When designing with this part, place the input/output 1 µF ceramic capacitors as close as possible to the IN and OUT pins and ensure the enable pin is driven by a logic-level source, not left floating. The datasheet also recommends keeping the junction temperature below 125 °C for reliable long-term operation, which usually requires less than ~250 mW dissipation in the SOT-23-5 footprint on a standard 1 oz copper 2-layer board. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone, with citations back to the original Microchip datasheet and current distributor listings as of 2026-10-16.
MIC5207-5.0YM5-TR - 180mA 5V Fixed LDO Regulator | Microchip
The Microchip Technology MIC5207-5.0YM5-TR is a 180 mA fixed-output low-dropout (LDO) linear regulator delivering a precise 5.0 V output from a 2.5 V to 16 V input rail, housed in a 5-pin SOT-23-5 surface-mount package. It features a typical dropout voltage of 165 mV at 150 mA load, ultra-low ground current of 720 µA at 100 mA, and initial output accuracy better than 3%. A reference bypass pin is included to further reduce output noise for noise-sensitive analog loads. An LDO (Low-Dropout) linear regulator is a type of voltage regulator that maintains a stable output voltage even when the input voltage is only marginally higher than the output voltage. LDOs sit within the broader hierarchy of voltage regulators → power management ICs → semiconductor devices. Unlike switching regulators, LDOs introduce no switching noise but dissipate (VIN - VOUT) × IOUT as heat, making them preferred for low-current, low-noise analog rails in battery-powered and portable systems. Key features include CMOS/TTL-compatible enable input for power sequencing, reversed-battery protection, internal current limiting, and thermal shutdown. The reference bypass pin (BYP) connects an external capacitor to lower output noise well below the level of a conventional LDO, suiting precision analog and RF applications. The MIC5207 series is offered in both fixed (1.5V–5.0V) and adjustable versions. The regulator uses a PNP pass transistor architecture with a low-noise reference and bandgap, optimized for hand-held and battery-powered devices. The 5-pin SOT-23-5 footprint is industry standard and supported by Microchip's evaluation boards, simplifying PCB integration. Quiescent current remains low across load, an important metric for sleep-mode current budgets in portable equipment. Typical applications include USB peripherals, wireless dongles, handheld instruments, RFID readers, cellular telephones, and battery-powered sensor modules. The fixed 5.0 V output is convenient for MCU rails, Bluetooth/Wi-Fi module supplies, and ADC reference buffering in space-constrained designs. Design tip: keep trace lengths from IN and OUT to their respective bypass capacitors short to maintain stability and minimize noise coupling. For lowest noise, place a 10 nF to 100 nF capacitor on the BYP pin. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.
MIC5209-3.3YS - 500mA 3.3V Fixed LDO Regulator SOT-223 | Microchip
The Microchip Technology MIC5209-3.3YS is a 500 mA low-noise low-dropout (LDO) linear regulator with a fixed 3.3 V output, packaged in a 3-pin SOT-223-3 (TO-261-4) package. It accepts input voltages from 2.5 V to 16 V, achieves a typical dropout of 10 mV at light loads and less than 500 mV at full 500 mA load, and provides output voltage accuracy better than 1 %. The MIC5209-3.3YS is specifically designed for handheld and battery-powered applications where long battery life and small PCB footprint are critical. An LDO (Low-Dropout) regulator is a type of linear voltage regulator that maintains a stable, accurate output voltage even when the input-to-output voltage differential is very small. Within the broader power-management integrated circuit (PMIC) hierarchy, LDOs sit beneath DC-DC converters and switching regulators as the low-noise, fast-transient alternative used when the input voltage is only slightly above the desired rail. LDOs add no switching ripple, but dissipate the voltage difference as heat. Key features of the MIC5209-3.3YS include reversed-battery protection, internal current limiting, overtemperature shutdown, and an ultra-low-noise reference architecture. The SOT-223-3 package exposes a metal tab that doubles as both pin 4 (connected to VOUT) and a thermal pad, allowing the part to sustain its 500 mA continuous rating without external heatsinking on typical 1 oz copper PCB pours. The internal architecture is a classic P-channel pass-MOSFET LDO with a bandgap reference and error amplifier. The P-channel element is why the dropout voltage is so low and why the device can survive reversed battery polarity (input more negative than ground). Stability is maintained with a small 1 µF ceramic output capacitor, simplifying BOM cost and board area versus older LDO generations that required tantalum or large electrolytic output caps. Typical applications include USB peripherals, microcontroller core or I/O rails, GSM modem power supplies, post-regulation after a switching converter, battery chargers, and instrumentation. The 3.3 V fixed output makes the MIC5209-3.3YS a natural fit for 3.3 V MCUs, Bluetooth/Wi-Fi modules, and low-power sensor interfaces where 5 V or 12 V inputs must be dropped down cleanly. A key design tip: keep trace lengths short between the output pin tab and the load, because the SOT-223 tab is the primary power and thermal path. For applications above ~250 mA continuous, increase copper area under the tab to keep junction temperature below 125 °C. Per the Microchip datasheet, the derating begins around 1 W dissipation in free air. This page synthesizes distributor pricing, same-package drop-in alternatives, and design notes drawn from the Microchip datasheet - information not collected in one place on the manufacturer product page.
MIC5209-3.3YS-TR - 500mA 3.3V Low-Noise LDO | Microchip
The Microchip Technology MIC5209-3.3YS-TR is a 500 mA low-noise LDO linear voltage regulator with a fixed 3.3 V output, better than 1% output accuracy, and a dropout voltage of typically 10 mV at light loads and less than 500 mV at full 500 mA load, housed in a SOT-223-3 (SOT-223, 3-pin plus tab) surface-mount package. An LDO (low-dropout regulator) is a type of linear voltage regulator that maintains a regulated output voltage even when the input supply is only slightly above the output. Within the power management IC hierarchy, LDOs sit downstream of switching converters or battery rails, providing clean, low-noise point-of-load regulation for analog and digital loads. Key features of the MIC5209-3.3YS-TR include 500 mA output current capability, ultra-low dropout for extended battery runtime, low ground current to prolong battery life in hand-held devices, better than 1% output voltage accuracy, and internal protection consisting of reversed-battery protection, current limiting, and overtemperature shutdown. Ultra-low-noise capability is a hallmark of the MIC5209 family. Architecturally, the MIC5209 uses a precision voltage reference and error amplifier driving a PNP pass element, which enables the very low dropout figure. The low quiescent (ground) current is deliberately optimized for battery-powered operation, and the SOT-223 package offers a thermally efficient tab that doubles as the output pin, simplifying PCB thermal design. Typical applications include hand-held and battery-powered instruments, cordless telephones, portable computing and communication devices, electronic scales, and general-purpose point-of-load regulation from 5 V or Li-ion rails down to a 3.3 V logic or analog rail. Design consideration: at 500 mA load with a large input-to-output differential, power dissipation in the SOT-223 package becomes the limiting factor; keep VIN-VOUT small or provide adequate copper area on the tab. This page synthesizes distributor pricing, drop-in alternatives, design notes, and application guidance not found in the manufacturer datasheet.
MIC5219-3.3YM5 - 500mA 3.3V LDO Regulator | Microchip SOT-23-5
The Microchip Technology MIC5219-3.3YM5 is a 500 mA peak-output, fixed 3.3 V low-dropout (LDO) linear regulator housed in a 5-pin SOT-23 surface-mount package. Per the manufacturer datasheet, the MIC5219 family delivers better than 1% output voltage accuracy, ultra-low dropout voltage (typically 10 mV at light loads, less than 500 mV at 500 mA), and reverse-battery protection on the input. The fixed 3.3 V output variant (MIC5219-3.3YM5) eliminates external feedback resistors and simplifies BOM for 3.3 V rails. An LDO (Low-Dropout) linear regulator is a type of voltage regulator that maintains a stable output voltage even when the input voltage is very close to the output voltage, with dropout voltages much lower than classic 7805-style regulators. LDOs sit within the power management IC hierarchy and trade efficiency for noise: unlike switching regulators, an LDO adds no switching ripple, which is critical for analog and RF subsystems. The MIC5219 family is engineered specifically for battery-powered portable systems where extended runtime, low quiescent current, and low dropout at high peak current are mandatory. Key features include a TTL/CMOS-compatible shutdown/enable input that drops quiescent current nearly to zero when disabled, current limiting, overtemperature shutdown, reversed-battery protection, and an ultra-low-noise option across the family. Output accuracy is better than 1% across line, load, and temperature. Ground current is minimized to prolong battery life, and the small SOT-23-5 footprint enables compact PCB designs. The YM5 industrial temperature grade supports -40 °C to +125 °C operation. Typical applications include USB peripherals and dongles, portable instrumentation, handheld terminals, wireless sensor nodes, post-regulation after switching converters, and any 3.3 V microcontroller or sensor bias rail where low noise and long battery life are priorities. The MIC5219-3.3YM5 also works well as a clean local rail for low-power MCUs such as PIC microcontrollers. When designing with this part, place the input and output bypass capacitors immediately adjacent to the IC with short, wide traces, and respect the absolute maximum input voltage. The shutdown pin can be driven from a GPIO for sequenced power-up in multi-rail systems. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.
MIC5233-3.3BM5 - 100mA 36V LDO Regulator 3.3V | Microchip
The Microchip MIC5233-3.3BM5 is a 100 mA, high-input-voltage, low-quiescent-current CMOS LDO regulator with a fixed 3.3 V output, packaged in a 5-pin SOT-23 (M5). The MIC5233 family is engineered to deliver high accuracy and ultra-low ground current from input rails up to 36 V, making it ideal for multi-cell Li-Ion battery stacks, USB-powered designs, and 12 V/24 V industrial rails. Key electrical headline specifications include 100 mA continuous output current, 450 mV maximum dropout at full load, 2.0% initial output accuracy, and typically 18 µA quiescent current (the 'ultra-low IQ' that distinguishes the MIC5233 family from older Micrel designs). An LDO (Low-Dropout) linear regulator is a type of voltage regulator that maintains a stable, low-noise output voltage even when the input voltage is only marginally higher than the desired output - the dropout voltage defines this minimum headroom. LDOs belong to the broader class of linear regulators within power management ICs and are preferred over switching regulators in noise-sensitive analog and RF signal paths because they inject no switching ripple into the output rail. Compared with a discrete Zener-plus-pass transistor reference, an integrated LDO like the MIC5233 shrinks the BOM, removes trimming, and provides built-in current limit, thermal shutdown, and reverse-battery protection. The MIC5233 uses a CMOS architecture with a P-channel pass transistor that intrinsically provides reverse-current blocking and zero reverse leakage when the input is shorted to ground. The 5-lead SOT-23 package adds an active-low enable (SHDN) pin, allowing the host MCU to turn off the regulator for power sequencing or to extend battery standby. The MIC5233 is a µCap LDO design, which means the output is stable with a single 2.2 µF ceramic capacitor - no tantalum or large ESR reservoir is required, simplifying PCB layout and shrinking the solution footprint compared to legacy LDOs that needed 10 µF tantalum output capacitors. Typical applications include always-on battery rails in 12 V industrial sensors, USB dongles, multi-cell Li-Ion packs (3-4 cells giving 9-16 V nominal), handheld instruments, and post-regulation downstream of a switching converter to remove switching ripple. Because quiescent current is well under 1 mA even at no load, the MIC5233 suits sleep-mode and IoT endpoints that must minimize sleep current on coin-cell or Li-Ion primary cells. When laying out the PCB, place the 2.2 µF ceramic output capacitor directly across the OUT and GND pins with the shortest trace possible; ESRs below 200 mΩ ensure loop stability. Avoid routing noisy switching traces near the feedback network, and ensure the input trace has sufficient copper width to handle the worst-case 100 mA continuous load without excessive voltage droop. This page synthesizes MIC5233 family datasheet specifications, distributor pricing, drop-in SOT-23-5 alternatives, and practical design notes that are not available on a stock DigiKey or Mouser listing.
MIC5239-5.0YS-TR - 5V 500mA Low-Iq LDO SOT-223 | Microchip
The Microchip Technology MIC5239-5.0YS-TR (ordered as MIC523950YSTR) is a fixed 5V, 500mA low-dropout (LDO) linear voltage regulator in a 4-pin SOT-223 (TO-261AA) package. It operates from input voltages up to 30V with an ultra-low quiescent current of 23uA and a dropout voltage of only 350mV at full load. A low-dropout regulator is a type of linear voltage regulator that maintains a regulated output even when the input voltage is only marginally higher than the output. Within the power management IC hierarchy, the MIC5239 belongs to the LDO family of positive linear regulators, positioned as a high-input-voltage, low-quiescent-current solution that sits between standard linear regulators and full switching converters. Key differentiating specifications include the 30V maximum input rating, which allows direct connection to high-voltage battery rails; the 23uA quiescent current, which minimizes standby drain in keep-alive power circuits; the 350mV dropout at 500mA, enabling efficient post-regulation after a switching converter; and uCap output architecture that is stable with low-ESR ceramic capacitors. Architecturally, the MIC5239 uses a PNP pass element driven by a precision reference and error amplifier. The low quiescent current is achieved through a biased internal supply technique rather than a conventional resistor string, so ground-pin current stays low across the full load range. The fixed 5.0V version integrates the feedback divider internally, eliminating external resistors and reducing BOM count. Typical applications include keep-alive and always-on power in automotive and industrial systems with high-voltage batteries, USB peripheral power where 500mA is required, post-regulation of switching converter rails for noise-sensitive analog circuitry, and battery-powered instrumentation that must sleep at microamp levels. For design, ensure input-to-output headroom stays above the 350mV dropout specification at the actual load current, and place at least 1uF of ceramic output capacitance close to the pin for stability, per the manufacturer datasheet. This page synthesizes distributor pricing as of 2026-10-16, drop-in same-family alternatives, and practical design notes not found in the manufacturer datasheet.
MIC5318-1.8YMT - 300mA 1.8V ULDO Regulator | Microchip | 6-TMLF
The Microchip Technology MIC5318-1.8YMT is a high-performance, single-output ultra-low-dropout (ULDO) linear regulator delivering a fixed 1.8 V output at up to 300 mA from a 2.5 V to 6 V input, housed in a 6-pin 1.6 mm x 1.6 mm Thin MLF (6-TMLF) package. The -1.8 suffix denotes the fixed output voltage; the MIC5318 family also offers -1.2, -1.5, -1.85, -2.5, -2.6, -2.8, -2.85, -3.0, -3.3, and -3.6 V options. The regulator combines low total output noise with high PSRR, making it an ideal solution for RF applications where clean power directly translates to phase noise and signal-to-noise performance. An LDO (Low-Dropout) linear regulator is a type of voltage regulator that maintains a stable output voltage even when the input voltage is very close to the output voltage. The MIC5318 belongs to the broader category hierarchy: ULDO -> LDO -> linear regulator -> voltage regulator -> power management IC. Compared with a standard NPN LDO, the MIC5318's PMOS pass topology enables an extremely low dropout of typically 90 mV at 300 mA, so a 2.5 V source can still regulate 1.8 V even as the cell discharges. Key differentiating specifications include 300 mA continuous output current, 90 mV typical dropout at full load, 60 dB PSRR at 1 kHz, 30 uVrms output noise, and 2% initial output voltage accuracy. The device tolerates ceramic output capacitors (uCap), requires no external compensation network, and integrates an active-low enable input for power sequencing in multi-rail designs. Thermal shutdown and current-limit protection are built in. Architecturally the MIC5318 uses a PMOS pass transistor paired with a precision bandgap reference and a discrete-loop error amplifier. The 6-TMLF exposed-pad package provides a low thermal resistance of approximately 78 C/W, allowing 300 mA delivery without external heatsinking at moderate VIN-VOUT differentials. Quiescent current is typically 90 uA with logic-low EN. Typical applications include portable and battery-powered devices where board space is critical, image sensors, GPS modules, RF power amplifiers, micro-controller cores, and noise-sensitive analog front ends. The fixed 1.8 V output also suits DDR memory termination rails and low-power MCU I/O supplies. When designing with the MIC5318-1.8YMT, place a 1 uF X5R/X7R ceramic input capacitor as close as possible to VIN and a 1 uF ceramic output capacitor at VOUT; ESR stability is maintained from near zero to 200 mOhm. The exposed pad must be soldered to a copper pour to meet the published thermal resistance. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes not found in the standalone manufacturer datasheet, giving procurement and design engineers a single decision-ready reference.
MIC5377YC5 - 150mA Adjustable LDO Regulator | Microchip | SC-70-5
The Microchip Technology MIC5377YC5 is a high-performance, general-purpose adjustable low-dropout (LDO) linear regulator that delivers up to 150 mA of output current in an ultra-compact 5-pin SC-70 package. The device accepts input voltages up to 5.5 V and supports an adjustable output range of approximately 1.0 V to 5.0 V set by an external resistor divider. Key specifications include a low dropout voltage, low quiescent current, and high output accuracy, making it a strong fit for space-constrained, battery-powered designs. According to the Microchip product page and distributor listings (DigiKey, Mouser, LCSC), the part is offered as MIC5377YC5-TR on a 3,000-piece reel. An LDO (low-dropout) linear regulator is a type of linear voltage regulator that maintains a stable, low-noise output voltage even when the input voltage approaches the output voltage, with a dropout voltage typically much lower than older standard regulators. Within the broader power-management hierarchy, an LDO belongs to the family of linear regulators, which in turn are a subclass of voltage regulators, themselves part of the power-management integrated circuit (PMIC) category of semiconductors. LDOs are valued over switching regulators in applications where switching ripple and EMI must be minimized, and the small VIN-VOUT differential produces acceptable thermal dissipation. Key features of the MIC5377YC5 include 150 mA continuous output current, low quiescent current to maximize battery life, internal soft-start circuitry, current-limit protection, and thermal-shutdown protection. The enable pin (where applicable in the MIC5376/8 family) supports an auto-discharge resistive load that pulls the output down when disabled, eliminating residual charge on downstream loads. The 5-pin SC-70 package is one of the smallest regulator footprints in the industry, ideal for hand-held, wearable, and IoT form factors where every square millimeter of PCB area is at a premium. Technically, the MIC5377 uses a PNP pass-element architecture that delivers low dropout and fast transient response. Stability is achieved with small ceramic input and output capacitors (typically 1 µF X7R), simplifying BOM cost and PCB layout. The adjustable variant allows designers to set any output voltage within its supported range, providing flexibility across multi-rail systems. Typical applications include portable and wearable electronics, IoT sensor nodes, wireless modules, hand-held instruments, and post-regulation stages after switching converters. When designing with this part, ensure the input voltage stays within the absolute maximum rating, use ceramic bypass capacitors close to the pins, and verify that the worst-case power dissipation (PD = (VIN - VOUT) × IOUT) stays within the SC-70 thermal envelope. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not consolidated in the manufacturer datasheet alone.
MIC5378YMT - 150mA Adj LDO, 1.2x1.2 TMLF-8 | Microchip
The Microchip Technology MIC5378YMT is a high-performance, ultra-small low-dropout (LDO) linear regulator that delivers up to 150 mA of output current from an adjustable output in an 8-pin 1.2x1.2 mm Thin MLF (TMLF-8) package. It is part of the MIC5375/6/7/8 family of general-purpose regulators, with the MIC5378 specifically offering an adjustable output voltage and an internal auto-discharge resistor on the output when disabled. An LDO (Low-Dropout) linear regulator is a type of voltage regulator that maintains a stable output voltage even when the input voltage approaches the output voltage, characterized by dropout voltages well under 1 V. In the broader component taxonomy, an LDO is a sub-class of linear regulator, which is itself a sub-class of voltage regulator, which sits under the power management IC umbrella, all of which are integrated circuits in the semiconductor family. The MIC5378 belongs to the small-package LDO category designed for portable, space-constrained electronics. Key features of the MIC5378YMT include an input voltage range typically covering 2.5 V to 5.5 V (per the MIC5375/6/7/8 datasheet family), a low quiescent current suited to battery-powered designs, and an output that is user-adjustable via an external resistor divider. The part also includes an internal discharge transistor that pulls the output to ground when disabled via the EN pin, eliminating residual charge on downstream loads. Architecturally, the MIC5378 uses a P-channel MOSFET pass element combined with an internal bandgap reference and error amplifier, providing tight line and load regulation. The 1.2x1.2 mm TMLF package integrates the die and exposed thermal pad for low thermal resistance in a footprint compatible with portable product miniaturization. Typical applications include portable and battery-powered devices, wearable electronics, IoT sensor nodes, smartphones, and post-regulation for switching converters in compact subsystems. The MIC5378YMT is particularly useful as a clean post-regulator following a noisy DC-DC converter, providing low-noise rail conditioning for RF, audio, or precision analog blocks. When designing with this part, place input and output ceramic bypass capacitors as close as possible to the IC pins and ensure the EN logic level is properly driven. The auto-discharge feature should be considered when sequencing multiple rails, as disabled outputs will be pulled low and may briefly source current from downstream caps. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes that go beyond what is published in the manufacturer datasheet, helping engineers quickly evaluate the MIC5378YMT for new designs and BOM risk mitigation.
MIC5504-1.8YM5-TR - 300mA 1.8V LDO SOT-23-5 | Microchip
The Microchip Technology MIC5504-1.8YM5-TR is a 300 mA fixed-output LDO linear voltage regulator with a 1.8 V output, an input range of 2.5 V to 5.5 V, and an enable pin with internal pull-down plus auto-discharge, housed in a 5-pin SOT-23-5 surface-mount package. An LDO (low-dropout) linear regulator is a type of voltage regulator that maintains a stable output voltage even when the input voltage is only slightly above the output. Within the power management IC hierarchy, LDOs sit alongside switching regulators as the preferred choice for low-noise, low-current rails where simplicity and small size matter more than conversion efficiency. Key features of the MIC5504 include a fixed 1.8 V output trimmed by current trimming during manufacture, 300 mA output current capability, an auto-discharge function that pulls the output low when the enable pin is low, and an internal enable pull-down that guarantees a defined disabled state when EN floats. Operation is specified from -40C to +125C. The MIC5504 is a member of the MIC5501/2/3/4 family described in Microchip datasheet DS20006006B. Internally, each device integrates a reference voltage source, error amplifier, driver transistor, current limiter, and phase compensation, so external support circuitry reduces to input and output capacitors. The MIC5502 and MIC5504 add auto-discharge; the MIC5503 and MIC5504 add the enable pull-down. This makes the MIC5504 the most feature-complete member of the family. Typical applications include battery-powered portable devices powered from single-cell Li-ion cells, post-regulation of 5V or 3.3V rails for MCUs, RF modules, and sensor supplies where a defined output state during shutdown is required for system sequencing. Design consideration: keep input voltage at least 2.5V to guarantee regulation, and rely on the auto-discharge (rather than a bleed resistor) to discharge the output capacitor during shutdown, which speeds up power cycling in duty-cycled IoT nodes. This page synthesizes distributor pricing, drop-in alternatives, pinout, and practical design notes not found in the manufacturer datasheet, with prices as of 2026-10-12.
MIC5800BN - 4-Bit Latched Driver 500mA 14-DIP | Microchip
The Microchip Technology MIC5800BN is a 4-bit parallel-input latched driver delivering up to 500 mA per channel from CMOS data latches driving bipolar Darlington transistor outputs, housed in a 14-pin DIP (0.300 inch, 7.62 mm) through-hole package operating from a 5 V to 12 V supply. A latched driver is a type of power driver IC that combines digital logic (data latches and control circuitry) with power output transistors on a single die. In the semiconductor hierarchy it sits between simple logic ICs and discrete power transistors: logic circuits set the desired output state, the latch holds that state on command, and the Darlington pair amplifies it to drive high-current loads such as relays, solenoids, lamps, and LED strings. This eliminates the need for discrete driver transistors and latch logic in mixed-signal control boards. Key features of the MIC5800BN include four CMOS data latches with common CLEAR, STROBE, and OUTPUT ENABLE control lines, a bipolar Darlington output stage rated for high-voltage, high-current operation, and a classic through-hole 14-DIP footprint that simplifies prototyping, rework, and legacy board maintenance. The 200 kohm on-state output characteristic reflects the Darlington output structure, and the 500 mA per-channel rating allows direct drive of relays and printer-head solenoids. Architecturally, each of the four channels consists of a CMOS latch feeding a Darlington transistor driver. Data on the parallel inputs is transferred to the latches on a STROBE edge; the OUTPUT ENABLE gate turns all outputs on or off simultaneously, and CLEAR resets all latches. CMOS control circuitry keeps input drive requirements low, allowing direct interface to 5 V logic families. Typical applications include relay and solenoid driving in industrial control panels, hammer/solenoid drivers in impact printers, incandescent lamp and LED segment drivers, and general-purpose high-current peripheral interfacing in legacy equipment maintenance. Design consideration: Darlington outputs saturate at roughly 1 V even at moderate currents, so plan load budgets and thermal margins accordingly, and use adequate base-referenced pulldowns on unused inputs. This page synthesizes distributor pricing, verified specifications, drop-in alternative analysis, and practical design notes not found in the manufacturer datasheet.
MIC5800YM - 50V 4-Bit Latched Driver SOIC-14 | Microchip
The Microchip Technology MIC5800YM is a high-voltage, high-current 4-bit parallel-input latched driver integrating four CMOS data latches, bipolar Darlington output stages, and CMOS control logic, packaged in a 14-pin SOIC. It delivers up to 500 mA per channel and supports output voltages up to 50 V, making it a drop-in interface between low-power microcontrollers and inductive, relay, solenoid, or lamp loads. What is a latched driver? A latched driver is a power-management IC that holds the last-written logic state on its outputs until the host writes a new value, freeing the microcontroller from continuous PWM or GPIO refresh. Within the broader hierarchy, latched drivers fall under power management ICs (PMICs) and are commonly classified alongside power distribution switches and load drivers. The MIC5800 sits between the digital control domain (MCU) and the high-power load domain (relay coils, stepper windings, Nixie/LED arrays), providing level shifting, current amplification, and transient protection in a single device. Key specifications include four parallel CMOS-compatible data inputs (D1–D4), common STROBE and CLEAR controls, an OUTPUT ENABLE pin, 50 V minimum output breakdown, and 500 mA continuous sink current per channel. The bipolar Darlington pairs achieve typical VCE(sat) around 1.0 V at low currents, with integral flyback clamping diodes for inductive loads. Each output can be paralleled to increase current capability, and the device operates from a single 5 V logic supply. Architecturally, the MIC5800YM combines CMOS latches with bipolar Darlingtons in a mixed-process BiCMOS design, ensuring low quiescent current on the logic side while the output transistors handle the high-voltage and high-current loads. The latches are edge-triggered by STROBE and asynchronously cleared by CLEAR, allowing deterministic update of all four channels simultaneously with predictable timing. Typical applications include relay and solenoid drivers, stepper motor phase drivers, LED or lamp multiplex displays, print-head driver arrays, and high-side or low-side switching of 12–48 V industrial loads. The MIC5800YM is also widely used in legacy test equipment and telecom line-interface boards where bipolar drive strength is preferred over MOSFET-only switches. When designing with the MIC5800YM, place a 0.1 µF decoupling capacitor close to VDD and respect the 50 V absolute-maximum output rating. The Darlington outputs have a saturation voltage that must be budgeted against load supply headroom, especially when driving low-voltage relays from a 5 V rail. This page synthesizes verified distributor pricing, drop-in alternatives from the same MIC58xx family and competing bipolar latched drivers, and practical design notes that complement the Microchip datasheet.
MIC5842YN - 8-Bit Serial-In Latched Driver, 500mA, 18-DIP | Microchip
The Microchip Technology MIC5842YN is an 8-bit serial-input latched driver fabricated with BiCMOS technology and housed in an 18-pin PDIP (DIP-18) through-hole package. It integrates an 8-bit CMOS shift register, CMOS control logic, and eight CMOS data latches followed by eight bipolar Darlington output stages rated at 500 mA continuous per channel with a 50 V minimum load-voltage rating per output. A latched driver is a type of peripheral power driver IC that accepts serial data from a microcontroller or logic controller, latches it for steady-state retention, and uses high-current bipolar outputs to switch inductive, capacitive, or lamp loads. It sits in the family of power management and load driver ICs (PMIC -> Load Driver -> Serial Latched Driver -> Peripheral Driver), bridging low-power CMOS logic and high-current real-world loads. Key features include a wide 5 V to 15 V supply operating range, output transient capability of 80 V per channel for inductive load turn-off, 500 mA continuous sink current per channel, an active-low STROBE latch-enable input, a serial data output pin for cascading multiple MIC5842 devices, and built-in input pull-up structures. The BiCMOS architecture gives the part its combination of low-power CMOS logic and high-current bipolar drive in a single die. The MIC5842YN is typically used to drive relays, solenoids, lamps, LED arrays, stepper motor windings, and incandescent displays. By clocking data into the shift register one bit at a time and then latching the parallel outputs simultaneously, designers can control up to eight high-current loads using only three or four microcontroller pins. When designing with this part, place a 0.1 uF decoupling capacitor close to VCC (Pin 6) and use flyback diodes on inductive loads or rely on the IC's internal clamp diodes. Output ground returns to GND at Pin 3. Maximum package dissipation must be observed when all eight outputs are fully loaded.
MIC803-46D2VM3-TR - 4.63V Processor Supervisor | Microchip
The Microchip Technology MIC803-46D2VM3-TR is a single-voltage microprocessor supervisor with a 4.63 V reset threshold, 20 ms reset delay, and open-drain reset output in a 3-pin SOT-23 package. It monitors a 1.2 V to 5.5 V supply and provides accurate power-fail detection for microprocessor, microcontroller, and embedded systems. A voltage supervisor, also called a supervisory circuit or reset controller, belongs to the power-management IC hierarchy. It monitors a system supply and signals the digital controller when voltage crosses a programmed threshold. This prevents a processor from operating below its valid input range, which can cause unreliable execution, corrupted memory, or unpredictable peripheral behavior. The key MIC803-46D2VM3-TR features include a 4.63 V nominal reset threshold, ±2.5% threshold tolerance, open-drain active-low reset output, and a 20 ms reset delay. Its three-terminal implementation keeps the circuit compact and suitable for space-constrained embedded equipment. The open-drain output allows the reset node to be pulled up to the local logic supply and permits wired connection with other supervisor signals. This variant belongs to the MIC803 family, whose part-number encoding identifies different reset thresholds and timing options. The D2 designation is associated with the 20 ms reset delay, while 46 identifies the 4.63 V threshold. Exact accuracy, hysteresis, current consumption, and temperature limits should be confirmed in the Microchip MIC803 datasheet before production release. Typical uses include monitoring 5 V processor rails, industrial controllers, battery-powered instruments, automotive electronics, IoT equipment, and consumer products. Place the device near the protected supply or logic rail and route the reset trace away from high-current switching nodes. A pull-up resistor is required on the open-drain reset output, and its value should balance rise time, power consumption, and downstream reset-input capacitance. The primary design trade-off is fixed threshold selection versus adjustable monitoring. This part offers a simple, low-component-count solution for systems with a known rail voltage. For rails requiring programmable thresholds, wider tolerance, different delay, or active-high reset behavior, select a matching supervisor after checking polarity, timing, package pins, and maximum supply voltage. This page consolidates verified manufacturer and distributor information, identifies family-level replacement risks, and highlights the pull-up, layout, and threshold considerations that are not apparent from a distributor title alone. Datasheet links are provided for complete electrical characteristics and ordering details.
MIE1W0505BGY - 1W Isolated DC/DC Module, 5V Out | MPS
The Monolithic Power Systems MIE1W0505BGY is an isolated, regulated DC/DC power module delivering up to 1W of output power (5V output at 200mA) from a 3V to 5.5V input range, housed in a compact SOIC-16 wide body (WB) surface-mount package. An isolated DC/DC converter is a power module that transfers energy across a galvanic isolation barrier, keeping the secondary-side ground independent of the primary-side ground. Isolated converters sit within the power management IC hierarchy: power module -> isolated DC/DC converter -> switching regulator -> power supply. They are essential wherever ground loops, different voltage domains, or safety isolation are required, such as isolated communication interfaces, industrial sensor nodes, and gate-drive bias supplies. The MIE1W0505BGY stands out for its use of capacitive isolation technology for the feedback (FB) path, which regulates the output voltage without a traditional optocoupler or a precision-configurable reference IC. Eliminating the optocoupler reduces component count, improves long-term reliability (optocoupler CTR degrades over time), and enables a much smaller solution size than conventional 1W isolated modules. The module provides excellent load and line regulation across its full 3V-5.5V input range. Architecturally, the module integrates the power transformer, controller, synchronous rectification, and the capacitive FB isolator inside the SOIC-16WB molded body, presenting a single component that replaces a multi-component flyback design. Continuous short-circuit protection (SCP) and over-temperature protection (OTP), cited for the -5R-AEC1 family variant, safeguard the module against output faults and thermal stress. Typical applications include isolated RS-485/CAN transceiver bias supplies, isolated side-rails for gate drivers, industrial PLC I/O channel isolation, and 3.3V/5V logic-domain isolation in test equipment and battery-powered instruments. Design-wise, the wide 3V-5.5V input range lets a single module serve both 3.3V and 5V logic rails; verify that available input current margin covers the roughly 300mA-plus primary-side demand at 3.3V input for a full 200mA load. This page synthesizes distributor sourcing data, drop-in family alternatives, and practical design notes not found in the manufacturer product page.
MM3474P04VBE - 3-5 Cell Li-Ion Battery Protection IC | Mitsumi
The Mitsumi MM3474P04VBE is a multi-cell lithium-ion / lithium-polymer battery protection IC that integrates overcharge, overdischarge, overcurrent, and short-circuit detection for 3-, 4-, and 5-series cell packs, housed in a 20-pin TSOP-20D surface-mount package. It supports cascade connection for packs of 6 or more cells, with cell-count selection driven by an external SEL logic input. A battery protection IC (sometimes called a battery management protection IC, or PCM IC) is a dedicated analog/mixed-signal device that sits between a lithium-ion cell stack and the system load/charger. Its job is to monitor each cell voltage and the pack current, and to disconnect the charge/discharge MOSFETs whenever any parameter drifts outside a safe window. The MM3474 belongs to the broader hierarchy of power management ICs (PMIC), and specifically to the battery management sub-category that includes standalone protectors, monitor/gauging ICs, and chargers. Multi-cell protectors like the MM3474 are the analog front-end of every modern lithium battery pack. Key features include programmable overcharge detection in the 4.x V per-cell range, fixed overdischarge detection, charge/discharge overcurrent detection, short-circuit protection with sub-millisecond response, low quiescent current, and built-in cascade logic that lets a master MM3474 hand off higher cell-stack monitoring to a slave device. The TSOP-20D (5.0 mm x 6.4 mm) package with exposed thermal considerations is suited to space-constrained battery management boards inside 10.8 V, 14.4 V, and 18 V lithium packs. The MM3474P04VBE uses a precision bandgap reference and analog comparators to evaluate each cell voltage against internal thresholds, then drives an external dual-MOSFET gate path through CO and DO pins. The SEL pin logic selects 3-, 4-, or 5-cell operation; cascade wiring adds the V and C pins to inter-stack communication. The result is a single-IC protection solution that replaces a discrete op-amp + supervisor + reference design. Typical applications include power tool battery packs (3S-5S), e-bike and e-scooter packs, laptop battery packs, portable UPS and energy-storage packs, and 18 V / 20 V max cordless-tool platforms. It is also used in medical-cart battery packs and select industrial 24 V Li-ion stacks. A key design consideration is the external MOSFET selection - the CO/DO pins sink gate charge and must be sized for the pack's continuous discharge current. Designers should also follow Mitsumi's cascade wiring diagram when stacking beyond 5S, and place the IC close to the cell-tap resistors to minimize ground-loop noise on the sense lines. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes drawn from the MM3474 series specifications document rather than the bare pinout.
MM3513H01NRH - 1-Cell Li-Ion Cell-Balance Voltage Monitor | Mitsumi
The Mitsumi MM3513H01NRH is a single-cell lithium-ion / lithium-polymer voltage-monitor IC with built-in cell-balancing capability, fabricated on a high-voltage CMOS process and housed in a 5-pin SOT-25A (SOT-23-5 equivalent) surface-mount package. It is intended for monitoring the terminal voltage of a rechargeable Li-ion or Li-poly cell and for enabling passive cell-balancing in single-cell or single-string battery-pack applications where over-charge protection and long-term capacity matching are required. A lithium-ion battery monitor IC (sometimes called a battery monitor, cell-balance IC, or voltage monitor) is a small analog/mixed-signal device that continuously measures the cell voltage and, when used in a multi-cell stack, equalizes the state-of-charge across cells. Cell monitors sit below the gas-gauge IC in the battery-management hierarchy (cell monitor -> battery protection -> battery management IC -> power management), and they are essential in any Li-ion system that needs to survive hundreds of charge/discharge cycles without drifting capacity between cells. The MM3513 family is one of the most widely adopted Japanese alternatives to Western cell-monitor parts in compact consumer battery packs. The MM3513H01NRH integrates a precision voltage detector, a stable reference-voltage source, an internal oscillator, a counter/timer circuit, and the logic that drives an external cell-balancing MOSFET or resistor. Housed in the compact SOT-25A package with a -40C to +85C operating range, it is well suited for small-format battery packs where PCB area is constrained. Internally, the high-voltage CMOS process gives the device the ability to connect directly across the cell terminal while consuming only a few microamperes in operation and sub-microampere quiescent current when the cell is in balance. Each device in the MM3513 series is composed of voltage detectors, reference voltage sources, an oscillator, a counter circuit, and logical circuits, giving designers a self-contained monitoring solution that needs only a few external components. Typical applications include single-cell Li-ion battery packs in smartphones, wearables, Bluetooth earbuds, power banks, and small IoT devices where battery cell balancing extends usable capacity and protects the cell from over-voltage stress during charging. Industrial telemetry and backup battery modules also use the part where compact footprint and accurate per-cell voltage detection are required. When designing with the MM3513H01NRH, route the cell sense input directly to the battery terminal with a Kelvin-style connection to avoid IR drop across the protection-FET on-resistance, and decouple the supply pin with a 100 nF ceramic capacitor placed within 2 mm of the package. The balance output should drive an external MOSFET or a power resistor sized so that the balance current does not exceed the cell manufacturer's recommended balancing rate, typically C/20 to C/10. This page synthesizes verified distributor pricing, pin-compatible drop-in alternatives, and practical design notes for the MM3513H01NRH that are not consolidated in any single datasheet or catalog page.
MM5450YN - 34-Output LED Display Driver, 40-PDIP | Microchip
The Microchip Technology MM5450YN is a 34-output, non-multiplexed LED display driver in a 40-pin PDIP package, operating from a 4.75 V to 11 V supply with serial data input and continuous brightness control via a single pin. According to the manufacturer, it requires no load signal and features an enable pin for simple display control. An LED display driver is a dedicated power management IC that converts serial or parallel control data into per-segment constant or switched current outputs capable of directly driving LEDs. In the display-driver hierarchy, the MM5450 belongs to the non-multiplexed (direct-drive) class: each output drives one LED segment or lamp continuously, so no multiplex timing, no external transistors, and no refresh software are required. This contrasts with multiplexed drivers, which time-share fewer outputs across many digits. Key features include 34 open-drain-style outputs that can each sink current for direct LED connection, continuous analog brightness control by setting a reference current through a single variable resistor connected to the supply, a simple serial data interface requiring only a clock and data line, and a data-enable input that gates output updates. The 500 kHz-class serial clock rate allows fast full-frame refresh of all 34 outputs. The device is fabricated in an N-channel, metal-gate MOS process that produces low-threshold, enhancement-mode and ion-implanted depletion-mode devices, a mature process that yields robust, well-characterized output structures suited to long-life industrial displays. Typical applications include industrial panel meters, instrument front-panel displays, elevator and equipment status indicators, vending-machine and appliance LED arrays, and any static LED lamp or 7-segment cluster where a microcontroller must drive many LEDs with minimal I/O pins - only two or three MCU lines are consumed regardless of LED count. A key design consideration is output current setting: brightness is set globally through the single brightness pin resistor, so individual segment dimming is not possible; plan current-limiting resistors per output where segments of different colors share a display. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
MM5451YN - 35-Output LED Display Driver DIP-40 | Microchip
The Microchip Technology MM5451YN is a serial-input LED display driver with 35 output channels, operating from a 4.75V to 11V supply in a 40-pin plastic DIP (DIP-40, 0.600 inch / 15.24mm wide) package. An LED display driver is a dedicated power-management interface IC that sits between a digital controller (microcontroller, FPGA, or logic) and an LED load. In the display-driver hierarchy, the MM5451YN belongs to the non-multiplexed, directly driven class of LED drivers: each output sinks current continuously, so no multiplexing timing is required from the host and no external driver transistors are needed for typical segment loads. The MM5451YN is fabricated in an N-channel, metal-gate MOS process producing low-threshold enhancement-mode and ion-implanted depletion-mode devices. Its headline features are 35 open-drain-style current-sinking outputs, a serial data interface requiring only clock and data lines, and a single-pin brightness control: one external variable resistor from the brightness pin to the supply sets a reference current that scales all 35 outputs simultaneously. Because the part is non-multiplexed, each output runs at continuous duty cycle, giving maximum instantaneous brightness per segment and eliminating multiplex flicker. The 500 kHz-class serial clock rate allows a full 35-bit shift-register update in well under 100 microseconds, fast enough for animation on large bar-graph and status panels. Output capability is specified around 1.8V output voltage at 2.7 mA per output per FindIC's summary of the Micrel datasheet; for higher-current operation the datasheet output ratings should be consulted. Typical applications include industrial panel meters, instrumentation annunciator and bar-graph displays, appliance and white-goods LED indicators, elevator and HVAC status boards, and vending or kiosk front panels - anywhere a static LED array of up to 35 points must be driven from a small microcontroller with minimal pin count. A key design consideration: because the MM5451YN is not multiplexed, total package power dissipation scales directly with the number of lit segments and the per-segment current set by the brightness resistor, so thermal budgeting on the DIP-40 package is essential at high duty cycles. This page adds value beyond the datasheet by synthesizing distributor pricing, drop-in alternative analysis against the MM5450 and ST M5451 families, and practical design notes in one place.
MP1251DS-LF - Specialized Power-Supply Interface | MPS
The Monolithic Power Systems MP1251DS-LF is a specialized power-supply and converter interface integrated circuit packaged in an 8-pin SOIC. The verified distributor data identifies the device as a Last Time Buy part and lists an SMBus interface, SMT mounting, and suitability for power supplies, converters, and controller-interface applications. Those verified facts define its present role, while detailed electrical limits, timing values, register functions, and pin-level functions were not supplied and must be confirmed from the manufacturer datasheet before design release. A power-supply interface controller is a specialized class of power-management and interface IC that sits between a host controller and a regulated power subsystem. An SMBus-compatible device may be used for configuration, telemetry, control, or status exchange, but the exact commands and electrical implementation of MP1251DS-LF cannot be inferred from the distributor category alone. System designers should therefore treat the verified part identity, package, interface category, applications, mounting style, and lifecycle state as authoritative while sourcing missing functional data from the original documentation. The 8-SOIC package supports surface-mount PCB assembly and matches the package information reported by DigiKey and GlobalSpec. Surface mount is useful in compact power electronics because it avoids through-hole mechanical strain and supports automated assembly. However, the verified material does not provide body dimensions, pin pitch, thermal resistance, maximum supply voltage, operating temperature, current rating, or exposed-pad details. Those package and electrical attributes should not be inferred from the generic 8-SOIC label. Typical design targets suggested by the verified distributor records are power supplies, DC-DC converters, and controller-interface systems. In each case, the device should be evaluated for protocol compatibility, signal levels, timing, operating voltage, shutdown behavior, and fault handling. Because MP1251DS-LF is identified as Last Time Buy, procurement planning matters as much as electrical suitability. Buyers should confirm current distributor inventory, lifecycle timing, and authorized-channel traceability before committing a new production design. The most important layout precaution is to follow the exact manufacturer pinout and recommended decoupling once the original datasheet is obtained. Do not assign SOIC pins by convention or route SMBus signals before confirming their package numbers and alternate functions. Validate pull-ups, voltage-domain compatibility, ground return paths, and any exposed thermal or electrical requirements at the schematic-review stage. This product record consolidates the verified distributor status, package, interface class, application labels, source links, and sourcing implications for MP1251DS-LF. It deliberately leaves unavailable electrical and pin functions unresolved rather than manufacturing specifications, and it distinguishes verified purchasing information from engineering data that still requires manufacturer documentation.
MP1252DS-LF - Specialized 8-SOIC Power Interface | MPS
The Monolithic Power Systems MP1252DS-LF is a specialized power-supply, converter, and controller interface IC packaged in an 8-pin SOIC. The verified distributor data identifies the device as an 8-SOIC component, while its detailed electrical ratings, pin functions, operating limits, internal architecture, and application-specific performance are not included in the supplied records. Those unverified parameters are therefore reserved for datasheet review rather than inferred from the product category. A power-supply interface IC is a specialized block within the power-management semiconductor hierarchy. It can connect or control power-conversion functions, regulate system rails, or supervise power-system behavior depending on its internal implementation. Unlike a generic logic IC, such a device is selected for the electrical conditions and control functions associated with a power rail rather than for Boolean processing alone. The MP1252DS-LF belongs to this broader class of power-management ICs but should not be assigned a more specific regulator, converter, or controller function without confirmation from the manufacturer datasheet. The verified catalog record establishes an 8-SOIC package and categorizes the MP1252DS-LF as a specialized power-supplies, converters, and controllers interface part. Its package supports compact surface-mount assembly, but no verified dimensions, pin orientation, exposed pad, thermal rating, or land-pattern details are supplied. The distributor listings also associate the device with RoHS3 compliance, although the manufacturer document needed to verify additional environmental or automotive claims is absent. Typical design use cannot be assigned confidently from the provided evidence alone. Engineers should use MP1252DS-LF only after confirming that its input voltage, output behavior, current capability, reference voltage, switching or linear architecture, enable logic, and pin mapping satisfy the intended power-supply design. This conservative approach prevents a catalog-level package match from being mistaken for full electrical compatibility. For implementation, obtain the MP1251, MP1252 manufacturer datasheet identified in the verified listing and compare every operating limit and pin function with the target schematic. Pay particular attention to startup behavior, bypass components, compensation, switching-node layout, and thermal conditions. Do not reuse an existing footprint solely from its 8-SOIC designation. This page distinguishes verified catalog facts from missing technical data and avoids inventing unsupported electrical values. It also records that no verified drop-in substitute was identified, preventing an 8-SOIC package match alone from being presented as pin-to-pin compatibility. Engineers should request a quote for current price, stock, and lead time from an authorized distributor or XAIPART.
MP1476GTF-Z - 18V, 2A, 800kHz Sync Step-Down Converter | MPS
The Monolithic Power Systems MP1476GTF-Z is a fully integrated, high-frequency, synchronous rectified, step-down switch-mode converter with internal power MOSFETs, delivering up to 2A continuous output current in a 6-pin SOT-563 (TF) package. It accepts a wide 4.2V to 18V input range and produces an adjustable output from 0.8V to 10V at 800 kHz switching frequency, with internal soft-start and power-save mode for light-load efficiency. A buck (step-down) DC-DC switching converter is a power management integrated circuit that converts a higher DC input voltage into a lower, regulated DC output voltage by chopping the input with a high-frequency switch and filtering the resulting waveform through an LC network. Buck converters sit within the broader hierarchy of voltage regulators > DC-DC converters > switching regulators > power management ICs > semiconductors, and they are the dominant topology for high-efficiency point-of-load conversion in modern electronics. The MP1476's three key strengths are: (1) synchronous rectification with internal high-side and low-side MOSFETs eliminating the need for an external Schottky diode; (2) high 800 kHz switching frequency allowing tiny inductors and small ceramic output caps; and (3) Power-Save Mode (PSM) at light load, raising efficiency to >80% even at 10 mA loads. Additional features include internal soft-start to limit inrush current, cycle-by-cycle over-current protection, thermal shutdown, and an open-drain power-good indicator. Technically the device uses a peak-current-mode control architecture with an internal 0.8V reference. The high-side MOSFET's RDS(on) is approximately 100 mOhm and the low-side approximately 80 mOhm, which together minimize conduction loss. The wide 4.2V-18V input range supports both 5V and 12V system rails, including USB-PD, two-cell Li-ion battery packs, and industrial 12V bus power, while the small SOT-563 footprint suits space-constrained portable designs. Typical applications include USB Type-C/PD powered accessories, portable industrial handheld terminals, 12V-to-point-of-load conversion in embedded modules, single-cell Li-ion battery chargers (as a downstream converter), and FPGA/MCU core rail generation. The wide input tolerance and 2A output make it a workhorse for distributed power architectures. When designing with the MP1476, the inductor (typically 2.2 uH to 4.7 uH) and output capacitor (22 uF X5R minimum) selection dominate ripple performance. Keep the input capacitor loop compact to minimize switching noise injection, and avoid routing sensitive analog signals directly beneath the SW node. This page synthesizes XAIPART distributor pricing tiers, validated same-family MPS drop-in alternatives, and SOT-563 footprint cross-references in a single comparison table that the manufacturer datasheet and standard distributor listings do not present side-by-side.