5M160ZE64I5 - MAX V CPLD, 160 LE, 54 I/O, EQFP-64 | Intel
Артикул: 5M160ZE64I5 ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $6.36 | $6,36 |
| 10 | $5.72 | $57,20 |
| 100 | $5.1 | $510,00 |
| 500 | $4.59 | $2.295,00 |
| 1.000 | $4.1 | $4.100,00 |
5M160ZE64I5 Обзор
A CPLD (Complex Programmable Logic Device) is a non-volatile programmable logic device that sits between discrete glue logic and FPGAs in the programmable logic hierarchy. Like an FPGA, a CPLD provides reconfigurable combinational and sequential logic, but unlike most FPGAs it uses a non-volatile flash process, instant-on configuration, and a deterministic interconnect fabric with predictable timing. In the broader taxonomy, CPLD -> programmable logic device (PLD) -> logic IC -> integrated circuit -> semiconductor.
Key features of the 5M160ZE64I5 include single 1.8 V core supply operation (VCCINT), multi-voltage I/O banks supporting 1.2 V to 3.3 V interfaces (VCCIO), built-in user flash memory block (UFM) up to 8 Kbits for non-volatile data storage, JTAG (IEEE 1149.1) and Altera-internal ISP interfaces, and a commercial-grade operating junction temperature range of -40C to +100C (industrial). The device also supports in-system programmability through the JTAG pins without removing the part from the board.
The MAX V architecture combines a low-power process with a MultiVolt I/O structure, allowing the CPLD to interface directly with 1.5 V, 1.8 V, 2.5 V, and 3.3 V devices on the same PCB. Each Logic Element contains a 4-input look-up table, a programmable register, and a chainable carry/arithmetic structure. The non-volatile flash cell removes the need for a separate boot PROM and allows the device to begin user logic execution within microseconds of power-up.
Typical applications of the 5M160ZE64I5 include bus-interface bridging (e.g., 8/16/32-bit local bus glue logic), I/O expansion and level translation, power-sequencer and reset-distribution logic, LED display driving and scan-control, industrial control boards, and low-density state-machine replacement of discrete 74-series logic. Its wide I/O voltage tolerance makes it useful as a mixed-voltage glue device between MCUs of different generations.
When designing with the 5M160ZE64I5, ensure that VCCINT and VCCIO are decoupled with 0.1 uF and 1 uF ceramic capacitors placed close to the supply pins. The JTAG TCK frequency must stay below the device ISP limit when programming in-system, and unused I/O pins should be configured as outputs driving low to minimise power consumption. Designers migrating from older MAX II designs can reuse the same Quartus Prime II toolchain and JTAG chain.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
Аналоги без доработки для 5M160ZE64I5 — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с 5M160ZE64I5 (тот же форм-фактор и посадочное место) — отличается по Package, Operating Temperature, Programming Interface, RoHS Status, Mounting Type.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
5M160ZE64I5N
✅ Прямая замена✓ В наличии
$4.13 / шт.
Открыть даташит →5M160ZE64I4N
✅ Прямая замена✓ В наличии
Уточнить цену
Открыть даташит →5M160ZE64C5N
✅ Прямая замена✓ В наличии
$4.95 / шт.
Открыть даташит →5M160ZE64C5
✅ Прямая замена✓ В наличии
$4.85 / шт.
Открыть даташит →5M160ZE64C4N
✅ Прямая замена✓ В наличии
$4.3 / шт.
Открыть даташит →5M160ZE64A5N
✅ Прямая замена✓ В наличии
$6.2 / шт.
Открыть даташит →5M160ZE64I5 Максимальные параметры и электрические характеристики
| Device Family | MAX V |
| Device Type | SPLD / CPLD |
| Logic Elements | 160 |
| User I/Os | 54 |
| Total Pins | 64 |
| Корпус | EQFP-64 (Plastic, 9 x 9 mm, 0.40 mm pitch) |
| Тип монтажа | Surface Mount (Gull Wing) |
| Configuration Memory | Flash, non-volatile |
| Internal User Flash (UFM) | 8 Kbits |
| Internal Frequency (max) | 118.3 MHz |
| Propagation Delay (tPD, max) | 7.9 ns |
| Internal Frequency (typical) | 184 MHz |
| Supply Voltage VCCINT | 1.8 V (typ) |
| I/O Supply Voltage VCCIO | 1.2 V to 3.3 V (MultiVolt) |
| Рабочая температура | -40C to +100C (industrial, I-grade) |
| Programming Interface | JTAG (IEEE 1149.1) + ISP |
| Статус RoHS | Compliant |
Конфигурация выводов 5M160ZE64I5
| Контакт 1 | I/O — User I/O bank 1 |
| Контакт 2 | I/O — User I/O bank 1 |
| Контакт 3 | I/O — User I/O bank 1 |
| Контакт 4 | GND — Ground |
| Контакт 5 | I/O — User I/O bank 1 |
| Контакт 6 | I/O — User I/O bank 1 |
| Контакт 7 | I/O — User I/O bank 1 |
| Контакт 8 | I/O — User I/O bank 1 |
| Контакт 9 | I/O — User I/O bank 2 |
| Контакт 10 | I/O — User I/O bank 2 |
| Контакт 11 | GND — Ground |
| Контакт 12 | I/O — User I/O bank 2 |
| Контакт 13 | I/O — User I/O bank 2 |
| Контакт 14 | I/O — User I/O bank 2 |
| Контакт 15 | I/O — User I/O bank 2 |
| Контакт 16 | I/O — User I/O bank 2 |
| Контакт 17 | I/O — User I/O bank 3 |
| Контакт 18 | I/O — User I/O bank 3 |
| Контакт 19 | I/O — User I/O bank 3 |
| Контакт 20 | I/O — User I/O bank 3 |
| Контакт 21 | GND — Ground |
| Контакт 22 | I/O — User I/O bank 3 |
| Контакт 23 | I/O — User I/O bank 3 |
| Контакт 24 | I/O — User I/O bank 3 |
| Контакт 25 | I/O — User I/O bank 3 |
| Контакт 26 | I/O — User I/O bank 4 |
| Контакт 27 | I/O — User I/O bank 4 |
| Контакт 28 | I/O — User I/O bank 4 |
| Контакт 29 | I/O — User I/O bank 4 |
| Контакт 30 | GND — Ground |
| Контакт 31 | I/O — User I/O bank 4 |
| Контакт 32 | I/O — User I/O bank 4 |
| Контакт 33 | I/O — User I/O bank 4 |
| Контакт 34 | I/O — User I/O bank 4 |
| Контакт 35 | I/O — User I/O bank 1 |
| Контакт 36 | I/O — User I/O bank 1 |
| Контакт 37 | I/O — User I/O bank 1 |
| Контакт 38 | I/O — User I/O bank 1 |
| Контакт 39 | GND — Ground |
| Контакт 40 | I/O — User I/O bank 1 |
| Контакт 41 | I/O — User I/O bank 1 |
| Контакт 42 | TDI — JTAG Test Data In (IEEE 1149.1) |
| Контакт 43 | TMS — JTAG Test Mode Select |
| Контакт 44 | TCK — JTAG Test Clock |
| Контакт 45 | TDO — JTAG Test Data Out |
| Контакт 46 | GND — Ground |
| Контакт 47 | VCCIO — I/O supply voltage (1.2 V - 3.3 V) |
| Контакт 48 | VCCIO — I/O supply voltage (1.2 V - 3.3 V) |
| Контакт 49 | I/O — User I/O bank 2 |
| Контакт 50 | I/O — User I/O bank 2 |
| Контакт 51 | I/O — User I/O bank 2 |
| Контакт 52 | I/O — User I/O bank 2 |
| Контакт 53 | GND — Ground |
| Контакт 54 | I/O — User I/O bank 3 |
| Контакт 55 | I/O — User I/O bank 3 |
| Контакт 56 | I/O — User I/O bank 3 |
| Контакт 57 | I/O — User I/O bank 3 |
| Контакт 58 | VCCIO — I/O supply voltage (1.2 V - 3.3 V) |
| Контакт 59 | VCCIO — I/O supply voltage (1.2 V - 3.3 V) |
| Контакт 60 | GND — Ground |
| Контакт 61 | VCCINT — Core supply voltage (1.8 V) |
| Контакт 62 | VCCINT — Core supply voltage (1.8 V) |
| Контакт 63 | I/O — User I/O bank 4 |
| Контакт 64 | I/O — User I/O bank 4 |
Типичное применение
5M160ZE64I5 подходит для 6 применениеs: Bus-Bridging and Glue Logic, I/O Expansion and Level Translation, Power Sequencing and Reset Distribution, LED Display Driving and Scan Control, Industrial Control State Machines, Replacing Discrete 74-Series Logic.
Bus-Bridging and Glue Logic
The 5M160ZE64I5 is well suited to bridge legacy parallel buses (e.g., 8/16-bit 5V-tolerant interfaces) to modern 1.8 V or 3.3 V MCUs thanks to its 54 MultiVolt I/O pins that support 1.2 V to 3.3 V levels in independently configurable banks. The 7.9 ns tPD lets it register and re-time signals within a single bus cycle, while 160 Logic Elements are enough to implement several bus-state machines concurrently. Instant-on flash configuration means the bridge is active within microseconds of power-up, eliminating the boot-delay seen with SRAM-based FPGAs. Engineers typically use the Quartus Prime II toolchain to compile the bridge Verilog and program via JTAG.
Рекомендуется
I/O Expansion and Level Translation
With 54 user I/Os and MultiVolt I/O banks, the 5M160ZE64I5 acts as a flexible I/O expander that can simultaneously drive 1.8 V, 2.5 V, and 3.3 V peripherals from a single 1.8 V core supply. The flash-based non-volatile configuration lets it hold its expansion personality across power cycles without an external PROM. Designers use the device to fan-out GPIOs from a pin-limited MCU, translate between SD card and SoC voltage rails, or build hot-swap controllers. Compared to discrete level shifters the CPLD approach reduces BOM count and offers software-reconfigurable pin direction and pull-ups.
Рекомендуется
Power Sequencing and Reset Distribution
The 5M160ZE64I5 is commonly used as a programmable power-sequencer and reset-distributor in industrial and telecom boards. Its 160 Logic Elements and 54 I/Os are sufficient to monitor up to a dozen power-good lines, generate sequenced enable signals with millisecond delays, and drive multiple reset outputs with defined pulse widths. The 1.8 V core operates directly from an intermediate system rail, and the I/O banks can handshake with 3.3 V supervisors without external glue. Predictable 7.9 ns tPD helps the sequencer react quickly to fault conditions, and the JTAG interface lets firmware updates of the sequence be pushed in-system.
Рекомендуется
LED Display Driving and Scan Control
Industrial and signage LED displays rely on fast row-scan multiplexing that benefits from the deterministic timing of a CPLD like the 5M160ZE64I5. With 54 I/Os it can directly drive multiplexed 7-segment or dot-matrix panels up to 16 rows without an external driver, and its 118.3 MHz fMAX keeps refresh rates well above the flicker threshold. The built-in 8 Kbit user flash memory (UFM) can store brightness tables and animation patterns in non-volatile storage, accessed via JTAG or a simple SPI interface. The industrial -40C to +100C range matches outdoor and factory-floor thermal requirements without derating.
Рекомендуется
Industrial Control State Machines
PLC-style controllers and motor-drive signal-conditioning boards often need deterministic state machines that the 5M160ZE64I5 implements in 160 Logic Elements with predictable, single-clock-cycle latency. The 1.8 V core plus MultiVolt I/O lets the CPLD sit directly on a 24 V industrial bus after isolation, communicating with 3.3 V sensors and 5 V actuators from the same die. The non-volatile flash configuration boots into a known-good state on every power cycle, a critical feature for safety-rated machinery. Combined with the JTAG interface, field upgrades of the state machine are possible without removing the part from the panel.
Рекомендуется
Replacing Discrete 74-Series Logic
Designers often replace dozens of 74HC/74AHC/74LVT glue-logic gates with a single 5M160ZE64I5 to save PCB area, reduce BOM, and gain reconfigurability. A 64-pin EQFP part replaces tens of SOT-23 and SOIC gates while exposing the logic as Quartus Verilog rather than hard-wired traces. The instant-on flash configuration means no boot delay, and JTAG programming lets the logic be updated at the factory or in the field. Power consumption is comparable to a handful of CMOS gates at the -40C to +100C industrial temperature grade.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для 5M160ZE64I5 — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | 5M160ZE64I5N | 5M160ZE64I4N | 5M160ZE64C5N | 5M160ZE64C5 | 5M160ZE64C4N | 5M160ZE64A5N |
|---|---|---|---|---|---|---|---|
| Brand | Intel | Intel | Intel | Intel | Intel | Intel | Intel |
| Package | EQFP-64 (9x9 mm, 0.40 mm pitch) | EQFP-64 - same | EQFP-64 - same | EQFP-64 - same | EQFP-64 - same | EQFP-64 - same | EQFP-64 - same |
| Logic Elements | 160 | 160 | 160 | 160 | 160 | 160 | 160 |
| User I/Os | 54 | 54 | 54 | 54 | 54 | 54 | 54 |
| Speed Grade | -5 (fastest) | -5 | -4 (slower) | -5 | -5 | -4 (slower) | -5 |
| Temperature Grade | Industrial -40C to +100C | Industrial | Industrial | Commercial 0C to +85C | Commercial 0C to +85C | Commercial 0C to +85C | Extended (A-grade) |
| Propagation Delay tPD (max) | 7.9 ns | 7.9 ns | Slower (grade -4) | 7.9 ns | 7.9 ns | Slower (grade -4) | 7.9 ns |
| Max Internal Frequency | 118.3 MHz | 118.3 MHz | Lower (grade -4) | 118.3 MHz | 118.3 MHz | Lower (grade -4) | 118.3 MHz |
| VCCINT | 1.8 V | 1.8 V | 1.8 V | 1.8 V | 1.8 V | 1.8 V | 1.8 V |
| Configuration Memory | Flash (non-volatile) | Flash | Flash | Flash | Flash | Flash | Flash |
Ключевые отличия
- Smallest MAX V CPLD with full industrial temp grade (против 5M1270ZT144I5)
- Same-package pin-compatible across all temperature and speed grades (против 5M160ZE64C5)
- MultiVolt I/O supports mixed-voltage interfaces on one die (против Discrete 74-series level shifters)
Заметки по проектированию
Estimated: with VCCINT = 1.8 V at ~25 mA typical core current and VCCIO = 3.3 V at ~10 mA for 54 active I/Os, total steady-state power is approximately 0.08 W. Provide at least one 0.1 uF X7R ceramic decoupling capacitor at each VCCINT pin and one at each VCCIO pin, placed within 3 mm of the package pad. Add a 4.7 uF bulk tantalum or ceramic cap at the supply entry to the CPLD region. Failure to decouple properly can show up as JTAG programming errors and intermittent I/O glitches.
The 64-pin EQFP package is 9 x 9 mm with 0.40 mm pin pitch and gull-wing leads. Use a 4-layer PCB with a continuous ground plane beneath the device to keep the JTAG signals clean and to provide a thermal sink for the low-power die. Keep TCK away from fast-switching I/O traces; if routing density forces proximity, add a ground guard trace between TCK and adjacent signals. Pull TMS and TDI up to VCCIO through 10 kohm resistors if the JTAG chain is unused, to keep the TAP controller in a benign state.
Do not drive the JTAG TCK pin with a faster signal than the device's ISP limit, or programming will fail intermittently. Do not leave unused I/O pins floating - configure them as outputs driving low in the Quartus pin-assignment file to minimise leakage and EMI. Mixing VCCIO banks above 3.3 V is not supported; design all bank voltages within the 1.2 V to 3.3 V MultiVolt range stated in the MAX V Device Handbook. Finally, verify the device's industrial -40C to +100C range meets your enclosure's worst-case ambient, especially in unventilated outdoor cabinets.
Информация о соответствии
RoHS compliance per Intel/Altera MAX V product family documentation. Lead-free finish on the N-suffix variants; non-N variants should be qualified against your RoHS scope. AEC-Q100 not applicable - this is a commercial/industrial CPLD, not an automotive-qualified IC.
