5M40ZM64C5N - 32-Macrocell MAX V CPLD, 64-MBGA | Intel / Altera
Артикул: 5M40ZM64C5N ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $2.33 | $2,33 |
| 10 | $2.1 | $21,00 |
| 100 | $1.86 | $186,00 |
| 500 | $1.62 | $810,00 |
| 1.000 | $1.45 | $1.450,00 |
5M40ZM64C5N Обзор
A CPLD (Complex Programmable Logic Device) is a non-volatile programmable logic device that combines the deterministic timing of PAL/GAL architecture with modern flash-based configuration, positioned between discrete logic gates and full FPGAs in the programmable logic hierarchy. CPLD -> programmable logic -> logic IC -> semiconductor. Unlike SRAM-based FPGAs, MAX V devices retain configuration without an external boot memory, which simplifies PCB layout, reduces BOM cost, and guarantees instant-on behavior at power-up.
Key features include 32 macrocells (equivalent to 40 logic elements), 30 programmable I/O pins, 1.8 V core / 1.5 V, 1.8 V, 2.5 V, 3.3 V tolerant I/O banks, 7.5 ns pin-to-pin logic delay, JTAG-based IEEE 1149.1 boundary-scan and ISP, and a multi-volt core that allows direct interfacing with 1.5 V, 1.8 V, 2.5 V, and 3.3 V logic. The device operates over the commercial 0 °C to +85 °C junction range and supports 1,000 flash program/erase cycles with over 10 years of data retention.
The MAX V family uses a uniform 4-input look-up table fabric with a continuous routing fabric and an instant-on, single-chip configuration scheme, eliminating the need for an external configuration PROM. Its non-volatile flash memory lets designs boot in microseconds rather than milliseconds, which is critical for control-plane logic that must be ready before the host processor initializes. The 64-MBGA footprint occupies just 5 mm × 5 mm, helping engineers replace multiple discrete 74-series logic ICs in space-constrained boards.
Typical applications include I/O expansion and bus bridging for microcontrollers and SoCs, power-sequencing and reset distribution in multi-rail systems, board-level glue logic (address decoding, interrupt aggregation, status-LED driving), industrial control and sensor-interface conditioning, and as a configuration/control companion to larger FPGAs. The combination of low standby current, instant-on, and small BGA footprint makes it attractive for handheld instruments, USB Type-C accessories, and industrial sensor nodes.
When designing with this part, place the JTAG chain near the board edge connector for test access and keep the VCCINT and VCCIO rails well-decoupled with 0.1 µF and 1 µF ceramics as recommended in the MAX V handbook. Engineers migrating from 5M40ZE64C5N (EQFP-64) should note that this M-package uses a different ball-map footprint, so PCB rework is required even though both parts share the same die family.
This page synthesizes distributor pricing, same-family drop-in alternatives (5M40ZE64C5N, 5M1270ZF256C5N), and practical design notes that complement the manufacturer datasheet and Quartus II device handbook.
Аналоги без доработки для 5M40ZM64C5N — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с 5M40ZM64C5N (тот же форм-фактор и посадочное место) — отличается по Package, Programming Interface, Configuration Memory, Operating Temperature, Mounting Type.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
5M40ZM64C4N
✅ Прямая замена✓ В наличии
$0.48 / шт.
Открыть даташит →5M40ZM64A5N
✅ Прямая замена✓ В наличии
$2.55 / шт.
Открыть даташит →5M80ZM64C5N
✅ Прямая замена✓ В наличии
$1.6108 / шт.
Открыть даташит →5M40ZM64C5
✅ Прямая замена✓ В наличии
$4.05 / шт.
Открыть даташит →5M40ZM64C5N Максимальные параметры и электрические характеристики
| Family | MAX V |
| Device Logic Elements | 40 |
| Macrocells | 32 |
| Maximum Internal Frequency | 118.3 MHz |
| Pin-to-Pin Logic Delay (tPD) | 7.5 ns |
| Supply Voltage - Core (VCCINT) | 1.8 V |
| I/O Voltage Banks | 1.5 V / 1.8 V / 2.5 V / 3.3 V tolerant |
| Programmable I/O Pins | 30 (approximate, per MAX V 5M40Z datasheet family) |
| User Flash Memory | 8 Kbits |
| Configuration Method | Non-volatile flash, instant-on, single-chip |
| Programming Interface | JTAG (IEEE 1149.1) ISP |
| Standby Current (ICCSTBY) | 55 µA typical |
| Диапазон рабочих температур | 0 °C to +85 °C (commercial) |
| Корпус | 64-ball MBGA, 5 mm × 5 mm |
| Статус RoHS | Compliant |
| Тип монтажа | Surface Mount (BGA) |
Руководство по цоколевке 5M40ZM64C5N в корпусе 64-ball mbga, 5 mm × 5 mm
Цоколевка для 5M40ZM64C5N (корпус 64-ball mbga, 5 mm × 5 mm). Эта цифровая ИС включает выводы GPIO, интерфейсы связи (UART, SPI, I2C) и выводы питания. Обратитесь к техническому описанию производителя для альтернативных функций выводов и вариантов конфигурации. Необходимо для проектирования встраиваемых систем и трассировки печатных плат.
Нет подробных данных о распиновке для 5M40ZM64C5N.
Обратитесь к даташиту для полной конфигурации выводов.
Типичное применение
5M40ZM64C5N подходит для 6 применениеs: I/O Expansion and Bus Bridging, Power-Sequencing and Reset Distribution, Board-Level Glue Logic Replacement, Industrial Control and Sensor Interface, FPGA Configuration and Control Companion, USB Type-C Port Controller and Cable-Orientation Logic.
I/O Expansion and Bus Bridging
The 5M40ZM64C5N excels at expanding MCU or SoC I/O count and bridging between mismatched logic levels. Its multi-voltage I/O banks support 1.5 V, 1.8 V, 2.5 V, and 3.3 V directly, eliminating external level-shifters between, for example, a 1.8 V application processor and 3.3 V sensors. With 30 user I/O pins and 7.5 ns tPD, the part can decode address ranges and aggregate interrupts deterministically. The MAX V's instant-on, non-volatile flash configuration means the expansion logic is ready before the host boots, simplifying cold-start firmware. Reference designs pair the 5M40ZM64C5N with NXP Kinetis or STM32 host MCUs to add SPI-to-parallel LCD bridges, GPIO expanders, or keypad scanners in industrial HMI panels.
Рекомендуется
Power-Sequencing and Reset Distribution
The 5M40ZM64C5N is a deterministic power-sequencing controller for multi-rail systems. Its 7.5 ns pin-to-pin delay and multi-voltage I/O let it drive Enable pins on LDOs (such as TPS7A4701) in a fixed order while monitoring Power-Good flags, releasing downstream resets only after all rails are stable. Non-volatile flash configuration eliminates the cold-start race that affects SRAM-based FPGAs, so the sequencer is active before the host processor initializes. With 40 logic elements and 8 Kbits of user flash, the part can store trim values and fault logs for post-mortem debugging. The 55 µA standby current keeps quiescent draw minimal in battery-backed systems.
Рекомендуется
Board-Level Glue Logic Replacement
The 5M40ZM64C5N can replace 4-8 discrete 74-series logic ICs (decoders, multiplexers, latches, flip-flops) with a single 5 mm × 5 mm BGA, dramatically reducing PCB area and BOM count. Designers map address decoding, interrupt aggregation, and status-LED multiplexing into the CPLD's 32 macrocells using Quartus II schematic capture or VHDL. Unlike discrete gates, the CPLD allows late-stage design changes without board rework, accelerating time-to-market. The MAX V's 1.8 V core and 3.3 V-tolerant I/O are drop-in replacements for HC/HCT logic families, and JTAG ISP lets production engineers program boards in-circuit.
Рекомендуется
Industrial Control and Sensor Interface
The 5M40ZM64C5N's 0-85 °C commercial temperature range, 1.8 V low-power operation, and 55 µA standby current suit it for industrial sensor-interface conditioning and PLC I/O conditioning modules. Its JTAG ISP interface supports in-field firmware updates on installed equipment, reducing service-call costs. The CPLD can debounce mechanical switch inputs, implement digital filters on encoder quadrature signals, and synchronize sensor read timing across multiple channels. Pairing the part with a TI MSP430 or Renesas RX host MCU lets the system offload deterministic logic to the CPLD while the host runs higher-level control loops. The 64-MBGA's 5 mm × 5 mm footprint is small enough to fit inside standard industrial push-in terminals.
Рекомендуется
FPGA Configuration and Control Companion
The 5M40ZM64C5N is widely used as a configuration and control companion to larger FPGAs such as Cyclone IV/V or Lattice ECP5. The CPLD can hold user-mode control signals (reset, mode-select, LED-status) for the FPGA, freeing FPGA general-purpose I/O for application logic. Its instant-on behavior means configuration-control signals are valid at t=0, while the FPGA is still loading from flash, avoiding race conditions. Engineers also use the MAX V's 8 Kbits of user flash to store board serial number, MAC address, or calibration constants read by the FPGA over SPI at boot. The 64-MBGA footprint is small enough to mount on the underside of the FPGA footprint area.
Рекомендуется
USB Type-C Port Controller and Cable-Orientation Logic
The 5M40ZM64C5N's small MBGA footprint and 7.5 ns tPD make it a fit-and-forget USB Type-C cable-orientation and CC-pin controller in accessories, hubs, and docking stations. The MAX V can detect CC1/CC2 pull-up/pull-down states, swap the USB SuperSpeed differential pair routing via a 2:1 mux, and present the correct Rp/Rd combination to the upstream Type-C host - all without external configuration memory. With 55 µA standby current, the part contributes negligibly to the always-on accessory power budget. The 64-MBGA's 5 × 5 mm area fits inside the USB-C connector shroud, enabling single-board Type-C dongles that previously required an MCU.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для 5M40ZM64C5N — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | 5M40ZM64C4N | 5M40ZM64A5N | 5M40ZE64C5N | 5M80ZM64C5N | 5M40ZM64C5 |
|---|---|---|---|---|---|---|
| Brand | Altera / Intel | Altera / Intel | Altera / Intel | Altera / Intel | Altera / Intel | Altera / Intel |
| Package | 64-MBGA (5 × 5 mm) | 64-MBGA (5 × 5 mm) - same | 64-MBGA (5 × 5 mm) - same | 64-EQFP (different) | 64-MBGA - same | 64-MBGA - same |
| Macrocells | 32 | 32 | 32 | 32 | 64 | 32 |
| Logic Elements | 40 | 40 | 40 | 40 | 80 | 40 |
| Pin-to-Pin Delay (tPD) | 7.5 ns | 8.5 ns | 7.5 ns | 7.5 ns | 7.5 ns | 7.5 ns |
| Core Voltage (VCCINT) | 1.8 V | 1.8 V | 1.8 V | 1.8 V | 1.8 V | 1.8 V |
| Operating Temperature | 0 °C to +85 °C | 0 °C to +85 °C | -40 °C to +125 °C | 0 °C to +85 °C | 0 °C to +85 °C | 0 °C to +85 °C |
| User I/O Pins | 30 | 30 | 30 | 30 | 30 | 30 |
Ключевые отличия
- Smallest-footprint 32-macrocell MAX V CPLD with full I/O voltage flexibility (против 5M40ZE64C5N (64-EQFP))
- Extended-temperature variant available in the same MBGA footprint (против 5M40ZM64C5N vs 5M40ZM64A5N)
- Dual density options in identical package simplify design upgrades (против 5M40ZM64C5N vs 5M80ZM64C5N)
Заметки по проектированию
The 64-MBGA (5 × 5 mm) has a 0.5 mm ball pitch, which requires laser-drilled or micro-via PCB stack-ups (typical 4-layer 1 oz copper). Use NSMD (non-solder-mask-defined) pads to increase solder-joint reliability under thermal cycling. Place 0.1 µF and 1 µF X7R 0402/0201 ceramic decoupling capacitors within 1 mm of each VCCINT and VCCIO ball pair. A solid ground plane on layer 2 directly under the BGA improves thermal dissipation and reduces simultaneous-switching noise on the JTAG and I/O banks.
Do not confuse the M-package 5M40ZM64C5N (64-MBGA) with the E-package 5M40ZE64C5N (64-EQFP); they share the same die but have different land patterns and are not interchangeable on the same PCB. Always verify the package code (M vs E) and ball/lead count before ordering. Also note that 5M40Z series parts are 1.8 V core and require a separate 3.3 V-to-1.8 V regulator for VCCINT even when I/O banks run at 3.3 V - omitting this regulator is a common first-prototype error.
JTAG signals (TDI, TDO, TMS, TCK, TRST) must be routed with 50 Ω controlled impedance and pulled up to VCCIO through 10 kΩ resistors on TDI, TMS, and TCK. Keep the JTAG chain under 6 inches and avoid splitting the JTAG bus across multiple voltage domains without a level shifter - use a dedicated JTAG buffer (such as SN74LVC1G125 or FTDI FT2232H) when chaining multiple 1.8 V and 3.3 V CPLDs/FPGAs. According to the MAX V handbook, JTAG TCK frequencies above 16 MHz require termination at the TCK source to prevent reflections.
Информация о соответствии
RoHS compliant and lead-free per Altera/Intel product page and distributor listings. Not AEC-Q100 qualified - choose 5M40ZM64A5N for automotive-temp applications. Halogen-free status not explicitly stated in the verified data and should be confirmed with the latest manufacturer material declaration before IEC 61249-2-21 compliance checks.
