5M570ZT100A5N - MAX V CPLD, 440 Macrocells, 118.3 MHz | Intel
Артикул: 5M570ZT100A5N ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $18.5 | $18,50 |
| 10 | $16.2 | $162,00 |
| 100 | $13.85 | $1.385,00 |
| 500 | $11.4 | $5.700,00 |
| 1.000 | $9.75 | $9.750,00 |
5M570ZT100A5N Обзор
What is a CPLD? A Complex Programmable Logic Device is a non-volatile programmable logic IC that sits between simple glue-logic gates and full FPGAs in the programmable logic taxonomy. The MAX V family is implemented on a 0.18 um flash-based process with on-chip flash configuration memory, so MAX V parts configure in microseconds at power-up without external boot memory. The CPLD hierarchy: programmable logic -> CPLD -> MAX V family -> non-volatile logic -> glue logic replacement, commonly used for I/O expansion, interface bridging (e.g., SPI to parallel), and power-up sequencing.
Key features of the 5M570ZT100A5N include 440 macrocells across 8 logic array blocks (LABs), up to 74 user I/O pins, a built-in internal oscillator, on-chip flash memory, JTAG (IEEE 1149.1) and ISP (in-system programmability) support, and integrated pull-up resistors on each I/O. The 100-pin TQFP package provides a fine-pitch, surface-mount option suitable for compact designs. The device operates over an extended -40C to +125C (A grade suffix) junction temperature range and is qualified to the AEC-Q100 automotive standard per the Arrow listing.
Architecturally, the 5M570Z uses a classic MAX-family MultiCore architecture with interconnect across LABs, a flash configuration block, and a Joint Test Action Group (JTAG) interface supporting boundary-scan testing. The non-volatile flash eliminates external configuration devices and reduces BOM cost for glue-logic replacement tasks.
Typical applications include industrial control I/O expansion, automotive body and infotainment systems (the A grade suffix and AEC-Q100 make this part automotive-suitable), consumer electronics glue logic, microcontroller I/O expansion, SPI/I2C-to-parallel bus bridges, and power-sequencing controllers. The 118.3 MHz performance supports high-speed glue-logic interfaces such as SDRAM controllers and fast SPI peripherals.
When designing with the 5M570ZT100A5N, observe that the 100-pin TQFP footprint is shared with the EPM570T100 legacy part and other MAX V 570-macrocell variants, simplifying layout migration. The internal oscillator can replace an external clock for simple state-machine designs. Verify VCCIO bank voltages (1.8 V, 2.5 V, 3.3 V) match the connected peripherals in mixed-voltage designs.
This page synthesizes distributor pricing, AEC-Q100 qualification notes, drop-in same-package alternatives, and practical design considerations for the 5M570ZT100A5N that are not consolidated on any single manufacturer or distributor product page.
Аналоги без доработки для 5M570ZT100A5N — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с 5M570ZT100A5N (тот же форм-фактор и посадочное место) — отличается по Package, Programming Interface, Configuration Memory, User Flash Memory, MSL Level.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
5M570ZT100C5N
✅ Прямая замена✓ В наличии
$3.7 / шт.
Открыть даташит →5M570ZT100I5N
✅ Прямая замена✓ В наличии
$6.74 / шт.
Открыть даташит →5M570ZT100C4N
✅ Прямая замена✓ В наличии
$9.2 / шт.
Открыть даташит →5M570ZT144C5N
✅ Прямая замена ⚠️ Характеристики не проверены✓ В наличии
$7.25 / шт.
Открыть даташит →5M570ZT100A5N Максимальные параметры и электрические характеристики
| Family | MAX V |
| Device Logic Elements | 570 |
| Macrocells | 440 |
| Logic Array Blocks (LABs) | 8 |
| Maximum User I/O Pins | 74 |
| Maximum Operating Frequency | 118.3 MHz |
| Pin-to-Pin Logic Delay (tPD) | 9.0 ns |
| Core Voltage (VCCINT) | 1.8 V |
| I/O Voltage (VCCIO) | 1.8 V / 2.5 V / 3.3 V (multi-voltage I/O banks) |
| Корпус | 100-pin TQFP |
| Тип монтажа | Surface Mount |
| Configuration Memory | On-chip non-volatile flash |
| Programming Interface | JTAG (IEEE 1149.1), in-system programmable (ISP) |
| Operating Temperature (A suffix) | -40C to +125C |
| Automotive Qualification | AEC-Q100 (per Arrow listing) |
| Статус RoHS | Compliant |
| Internal Oscillator | Yes (on-chip) |
| User Flash Memory | Yes (on-chip) |
Руководство по цоколевке 5M570ZT100A5N в корпусе 100-pin tqfp
Цоколевка для 5M570ZT100A5N (корпус 100-pin tqfp). Эта цифровая ИС включает выводы GPIO, интерфейсы связи (UART, SPI, I2C) и выводы питания. Обратитесь к техническому описанию производителя для альтернативных функций выводов и вариантов конфигурации. Необходимо для проектирования встраиваемых систем и трассировки печатных плат.
Нет подробных данных о распиновке для 5M570ZT100A5N.
Обратитесь к даташиту для полной конфигурации выводов.
Типичное применение
5M570ZT100A5N подходит для 6 применениеs: Industrial PLC I/O Expansion, Automotive Body Controller, Microcontroller I/O Expansion, SPI/I2C to Parallel Bus Bridge, Power Sequencing Controller, Consumer Electronics Glue Logic.
Industrial PLC I/O Expansion
The 5M570ZT100A5N provides 440 macrocells and 74 user I/O pins in a 100-pin TQFP, making it well suited for PLC I/O expansion modules. Its -40C to +125C operating range (A grade) handles harsh factory-floor temperatures, and multi-voltage I/O (1.8/2.5/3.3 V) interfaces directly to 3.3 V MCU peripherals and 5 V-tolerant sensors via level shifters. The 9.0 ns tPD and 118.3 MHz fMAX easily satisfy scan-time requirements for 100 kHz digital I/O blocks.
Рекомендуется
Automotive Body Controller
The 5M570ZT100A5N is AEC-Q100 qualified and operates from -40C to +125C, making it suitable for automotive body controller modules controlling lighting, mirrors, and door modules. Its on-chip flash configuration means instant-on at battery reconnect, critical for retaining network nodes without boot delay. The 1.8 V core plus 3.3 V-tolerant I/O interfaces directly to modern automotive MCUs, and 74 I/O pins handle typical body-controller signal counts.
Рекомендуется
Microcontroller I/O Expansion
When an MCU runs out of GPIO or peripheral channels, the 5M570ZT100A5N adds 74 user I/O and flexible logic blocks. Designers connect it to the MCU via SPI (using 4-6 pins) and implement up to 70 generic digital I/O, PWM generators, or custom serial protocols in CPLD logic. The 118.3 MHz fMAX supports fast SPI transfers at 50 MHz clock rates, keeping interrupt latency low. On-chip flash and JTAG-ISP enable in-field reconfiguration if the I/O map changes.
Рекомендуется
SPI/I2C to Parallel Bus Bridge
The 5M570ZT100A5N excels as a bus bridge translating SPI or I2C commands into 8/16/32-bit parallel bus cycles for legacy peripherals, LCD controllers, or FPGAs. With 440 macrocells, designers implement full custom state machines for non-standard protocols, and 74 user I/O handle bidirectional data plus control lines. The on-chip user flash can store lookup tables or bootloader code, reducing host MCU firmware size.
Рекомендуется
Power Sequencing Controller
The 5M570ZT100A5N is widely used as a multi-rail power-sequencing controller for ASICs, SoCs, and FPGAs requiring strict rail-on/rail-off ordering. Each macrocell can drive a discrete power-good signal or FET gate with programmable delays, and the on-chip flash ensures deterministic startup without external MCU involvement. The 1.8 V core and 3.3 V I/O interface directly to typical PMBus or GPIO rails, and 74 I/O handle up to 30 sequenced rails.
Рекомендуется
Consumer Electronics Glue Logic
The 5M570ZT100A5N replaces 5-10 discrete 74-series glue-logic ICs (LVC, AHC, HC) in consumer products, reducing PCB area and BOM cost. The 100-pin TQFP package fits into a small footprint with 74 user I/O available, and the 1.8 V core plus multi-voltage I/O interfaces to modern SoCs running at 1.8 V while driving legacy 3.3 V peripherals. Its instant-on flash configuration eliminates boot delay for time-critical signal paths.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для 5M570ZT100A5N — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | 5M570ZT100C5N | 5M570ZT100I5N | 5M570ZT100C4N |
|---|---|---|---|---|
| Brand | Intel | Intel | Intel | Intel |
| Package | 100-pin TQFP | 100-pin TQFP - same | 100-pin TQFP - same | 100-pin TQFP - same |
| Macrocells | 440 | 440 | 440 | 440 |
| Maximum User I/O | 74 | 74 | 74 | 74 |
| Pin-to-Pin Delay (tPD) | 9.0 ns | 9.0 ns | 9.0 ns | 9.0 ns |
| Maximum Frequency (fMAX) | 118.3 MHz | 118.3 MHz | 118.3 MHz | 118.3 MHz |
| Operating Temperature | -40C to +125C (A grade) | -40C to +85C (C grade) | -40C to +100C (I grade) | -40C to +85C (C grade) |
| AEC-Q100 Qualified | Yes | No | No | No |
| Configuration Memory | On-chip flash | On-chip flash | On-chip flash | On-chip flash |
Ключевые отличия
- AEC-Q100 automotive qualification with -40C to +125C operation (против 5M570ZT100I5N)
- 440 macrocells in a 100-pin TQFP package (против 5M160ZT100A5N)
- On-chip flash configuration memory - no boot PROM required (против EPM570T100A5N (MAX II))
Заметки по проектированию
The 5M570ZT100A5N requires a stable 1.8 V VCCINT supply with a recommended 100 nF decoupling capacitor placed within 5 mm of the VCCINT pin. VCCIO pins are organized into multiple banks (1.8 V, 2.5 V, or 3.3 V) and each VCCIO bank should be bypassed with a 100 nF ceramic plus 4.7 uF bulk capacitor. Sequence VCCINT before VCCIO during power-up to prevent latch-up; a simple RC delay or external power-good signal can enforce sequencing if the rails come up simultaneously.
Route all JTAG signals (TMS, TDI, TDO, TCK) as a 4-wire bus with ground reference, keeping trace length under 50 mm to maintain signal integrity at TCK frequencies up to 33 MHz. Place a 10 kohm pull-up on TCK and TMS per the IEEE 1149.1 specification to ensure defined logic levels when the programmer is disconnected. The 100-pin TQFP has a 0.5 mm pitch; use 0.15 mm trace width with 0.15 mm spacing and 4-layer stack-up (signal-ground-power-signal) to route all 74 user I/O without dog-bones.
Do not confuse the 'A' suffix (automotive grade, -40C to +125C, AEC-Q100) with the 'I' (industrial, -40C to +100C, no AEC-Q100) or 'C' (commercial, -40C to +85C) suffixes - they are NOT electrically identical for qualification purposes. When migrating designs between grades, verify that the FPGA bitstream (POF file) generated for one grade works on the other, since speed grades may affect timing closure. Use Quartus Prime Design Assistant to check for unconstrained I/O or incomplete timing constraints before programming.
Информация о соответствии
RoHS and REACH compliant per distributor listings. AEC-Q100 qualified per Arrow listing. Lead-free and halogen-free per Intel MAX V family datasheet. Conflict-minerals compliant per Intel supplier declarations.