AD624BDZ - 25 MHz Low-Noise Instrumentation Amplifier | Analog Devices
Артикул: AD624BDZ ✗ Снят с производстваAD624BDZ Обзор
An instrumentation amplifier is a precision analog signal-conditioning device built to amplify small differential sensor signals while rejecting common-mode noise and interference. The AD624 family is commonly used with load cells, strain gauges, and pressure transducers because it combines differential input handling, high gain accuracy, low noise, and fast settling performance in one integrated circuit. In a typical measurement chain, the sensor converts a physical quantity into a small differential voltage, the AD624BDZ amplifies that voltage, and a downstream ADC or data-acquisition system performs digitization.
The AD624 offers several features suited to precision measurement systems. Its internal trimmed gain options eliminate the need for precision external feedback resistors for common gain settings, while its high bandwidth supports faster acquisition cycles than a conventional slow instrumentation amplifier. The 5 V/µs slew rate helps preserve signal fidelity during large transient responses, and the 15 µs settling time allows the amplifier output to stabilize rapidly between measurements. Low noise makes the device suitable for sensors whose useful signal amplitude is close to the measurement system’s noise floor.
The AD624BDZ uses a three-op-amp instrumentation-amplifier architecture to provide high input impedance and accurate differential gain. Its internal resistors and trim circuitry establish accurate gain without requiring external calibration resistors for the predefined gains. The device is intended for systems operating from dual positive and negative supplies, allowing bipolar sensor signals to remain centered around ground. The manufacturer identifies the AD624 as a precision, low-noise instrumentation amplifier with strong DC and AC performance.
Typical applications include industrial load-cell measurement, strain-gauge bridges, pressure-transducer interfaces, laboratory instrumentation, biomedical signal acquisition, and high-speed data-acquisition systems. The 16-lead ceramic-DIP package makes it suitable for equipment requiring a through-hole component and a conventional industrial or laboratory instrumentation architecture.
When using the AD624BDZ, confirm the supply voltage, gain configuration, input common-mode range, and output swing against the sensor and ADC interface. Place the device close to the transducer to minimize interference pickup on high-impedance sensor lines, and use suitable bypassing capacitors around the power pins. The ceramic DIP package also requires attention to socket or PCB through-hole alignment and thermal management during system assembly.
This page combines manufacturer specifications, package information, pricing references, and practical selection guidance for engineers evaluating the AD624BDZ in precision sensor-conditioning and data-acquisition designs.
Аналоги без доработки для AD624BDZ — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с AD624BDZ (тот же форм-фактор и посадочное место) — отличается по Package, Mounting Type, Input Offset Voltage, Settling Time, Slew Rate.
AD624BD
✅ Прямая заменаУточнить цену
Открыть даташит →AD624CDZ
✅ Прямая заменаУточнить цену
Открыть даташит →AD624SD/883B
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
AD624BDZ Максимальные параметры и электрические характеристики
| Product Type | Precision instrumentation amplifier |
| Number of Amplifiers | 1 circuit |
| Gain-Bandwidth Product | 25 MHz |
| Slew Rate | 5 V/µs |
| Settling Time | 15 µs |
| Input Offset Voltage | 75 µV |
| Supply Voltage Range | ±6 V to ±18 V |
| Trimmed Gain Settings | 1, 100, 200, 500, and 1000 |
| External Gain-Setting Components | Not required for trimmed gains |
| Input Signal Type | Differential |
| Корпус | 16-lead ceramic DIP |
| Тип монтажа | Through-hole |
| Статус RoHS | unknown |
| REACH Status | unknown |
| Automotive Qualification | not_applicable |
Руководство по цоколевке AD624BDZ в корпусе 16-lead ceramic dip
Цоколевка для AD624BDZ (корпус 16-lead ceramic dip). Этот аналоговый компонент имеет выводы входа, выхода и питания. Обратитесь к техническому описанию производителя для конфигураций выводов балансировки нуля, коррекции и разрешения. Идеально подходит для схем обработки сигналов и усилителей.
Нет подробных данных о распиновке для AD624BDZ.
Обратитесь к даташиту для полной конфигурации выводов.
Типичное применение
AD624BDZ подходит для 6 применениеs: Load-Cell Measurement, Strain-Gauge Signal Conditioning, Pressure Transducer Interface, High-Speed Data Acquisition, Biomedical Sensor Signal, Laboratory Instrumentation.
Load-Cell Measurement
The AD624BDZ suits load-cell front ends that produce small differential voltages from a bridge sensor. Its precision instrumentation-amplifier architecture provides high common-mode rejection while the low-noise, 25 MHz gain-bandwidth product supports fast measurement acquisition. Internal trimmed gains of 1, 100, 200, 500, and 1000 simplify calibration for common bridge sensitivities. The 5 V/µs slew rate and 15 µs settling time help the system settle quickly between successive readings.
Рекомендуется
Strain-Gauge Signal Conditioning
The AD624BDZ is appropriate for strain-gauge bridge conditioning where the useful differential signal is small and susceptible to interference. The device combines a 75 µV input offset specification with low noise, helping preserve measurement integrity in precision strain systems. Its selectable internal gains reduce external resistor requirements for common gain values, while the 16-lead ceramic DIP package fits through-hole instrumentation and test equipment.
Рекомендуется
Pressure Transducer Interface
The AD624BDZ can condition the millivolt-level output of a bridge-based pressure transducer while rejecting common-mode voltage present on the sensor lines. Its 25 MHz gain-bandwidth product and 15 µs settling time support fast data-acquisition sequences, and the 5 V/µs slew rate improves response to transient events. Internal trimmed gains from 1 through 1000 provide several sensitivity ranges without requiring a full external gain network.
Рекомендуется
High-Speed Data Acquisition
The AD624BDZ fits high-speed acquisition channels that need more bandwidth than a slow precision instrumentation amplifier. Its 25 MHz gain-bandwidth product, 5 V/µs slew rate, and 15 µs settling time allow output settling between measurements. The part is useful where sensor signals must be amplified before ADC sampling while preserving low noise and accurate differential behavior.
Рекомендуется
Biomedical Sensor Signal
The AD624BDZ can amplify small differential biomedical sensor signals when the circuit requires accurate offset control and low-noise amplification. The 75 µV input offset specification and internal trimmed gains help establish repeatable measurement conditions, while the fast settling behavior supports rapid signal sampling. Designers should still verify patient-safety isolation requirements, input protection, and applicable medical standards before connecting the amplifier to a clinical system.
Рекомендуется
Laboratory Instrumentation
The AD624BDZ is well suited to precision laboratory instruments that combine selectable gain, low noise, and rapid settling. The internal gain choices support repeatable setup for different sensor sensitivities, and the 25 MHz bandwidth allows acquisition systems to sample transient or time-varying inputs. Its through-hole ceramic-DIP package is convenient for laboratory electronics, modular instruments, and serviceable measurement platforms.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для AD624BDZ — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | AD624BD | AD624CDZ | AD624SD/883B |
|---|---|---|---|---|
| Package | 16-lead ceramic DIP | 16-lead ceramic DIP | 16-lead ceramic DIP | 16-lead ceramic DIP |
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Product Type | Precision instrumentation amplifier | AD624-family instrumentation amplifier | AD624-family instrumentation amplifier | AD624-family instrumentation amplifier |
Ключевые отличия
- Fast measurement settling (против AD624BD)
- Internal gain programming without external resistors (против AD624CDZ)
- Precision input offset specification (против AD624SD/883B)
Заметки по проектированию
Place the AD624BDZ close to the sensor input connector and route the differential input pair as a short, tightly coupled pair. High-impedance transducer lines should be kept away from switching nodes and digital timing signals. The manufacturer’s application guidance and pin-description table should be used to identify the input and supply pins on the 16-lead ceramic-DIP footprint.
The AD624BDZ requires positive and negative supplies in the ±6 V to ±18 V range. Confirm that both rails remain within limits under startup, load transients, and supply ripple. Use local decoupling close to the supply pins, with capacitor values and stability requirements selected from the manufacturer datasheet.
Do not assume that every AD624 suffix is an automatic drop-in replacement. Confirm the ceramic-DIP lead count, pin names, temperature grade, gain implementation, and required external components for AD624BD, AD624CDZ, or AD624SD/883B. For custom gains, follow the manufacturer’s resistor values and layout guidance rather than changing feedback components without stability checks.
The 25 MHz gain-bandwidth product, 5 V/µs slew rate, and 15 µs settling time make bandwidth and settling time important in acquisition systems. Account for the complete signal chain, including sensor capacitance, cable capacitance, output loading, and ADC acquisition time. Provide a defined settling interval before taking a measurement when the source changes rapidly.
Информация о соответствии
Compliance attributes are not specified for the AD624BDZ in the available product information. The 16-lead ceramic-DIP package and ±6 V to ±18 V supply range are identified, while detailed package drawing and ordering-grade information should be checked in the manufacturer datasheet.