ATMEGA32L-8PU - 8-bit AVR MCU 32KB 8MHz DIP-40 | Microchip
Артикул: ATMEGA32L-8PU ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $13.06 | $13,06 |
| 10 | $12.1 | $121,00 |
| 100 | $11.2 | $1.120,00 |
| 500 | $10.45 | $5.225,00 |
| 1.000 | $9.75 | $9.750,00 |
ATMEGA32L-8PU Обзор
A microcontroller (MCU) is a single integrated circuit that combines a processor core, program memory, data memory, and peripheral functions such as timers, UARTs, and ADCs into one chip. Within the embedded-systems hierarchy, the ATmega32 family sits in the 8-bit general-purpose MCU class, positioned between smaller ATmega8/16 devices and higher-performance AVR or ARM-based controllers. The AVR architecture uses a Harvard design with 32 general-purpose working registers directly connected to the ALU, executing most instructions in a single clock cycle - up to 8 MIPS throughput at 8 MHz.
Key features include 32 KB ISP Flash with read-while-write capability, a JTAG interface for boundary-scan and on-chip debugging, three flexible timer/counters (two 8-bit, one 16-bit with PWM), a byte-oriented two-wire serial (I2C-compatible) interface, an 8-channel 10-bit ADC with differential mode and programmable gain, and a programmable serial USART. The low-voltage 'L' variant operates from 2.7 V to 5.5 V, enabling 3.3 V battery-powered designs.
The ATMEGA32L-8PU supports six sleep modes (Idle, ADC Noise Reduction, Power-save, Power-down, Standby, Extended Standby) for aggressive power reduction, plus an on-chip RC oscillator, brown-out detection, and internal interrupt sources.
Typical applications include education and prototyping (the breadboard-friendly DIP-40 package), industrial sensor nodes, battery-powered instrumentation, and motor-control or building-automation controllers.
Design consideration: at 8 MHz the speed grade is derated below 4.5 V, so verify that your clock frequency and supply voltage combination is legal across the full operating temperature range.
This page synthesizes distributor pricing, drop-in alternatives within the ATmega family, pinout data, and practical design notes not found in a single manufacturer datasheet page.
Аналоги без доработки для ATMEGA32L-8PU — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с ATMEGA32L-8PU (тот же форм-фактор и посадочное место) — отличается по Package, Communication Interfaces, Operating Temperature, EEPROM, Debug Interface.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
ATMEGA32A-PU
✅ Прямая замена✓ В наличии
$3.85 / шт.
Открыть даташит →ATMEGA32A-PN
✅ Прямая замена✓ В наличии
$4.15 / шт.
Открыть даташит →ATMEGA32L-8PI
✅ Прямая замена ⚠️ Характеристики не проверены📋 Справочный аналог (нет в каталоге)
ATMEGA32L-8AC
✅ Прямая замена✓ В наличии
$5.85 / шт.
Открыть даташит →ATMEGA32L-8AI
✅ Прямая замена✓ В наличии
$5.62 / шт.
Открыть даташит →ATMEGA16L-8PU
✅ Прямая замена ⚠️ Характеристики не проверены✓ В наличии
$3.55 / шт.
Открыть даташит →ATMEGA32-16PU
✅ Прямая замена ⚠️ Характеристики не проверены✓ В наличии
$3.68 / шт.
Открыть даташит →ATMEGA32L-8PU Максимальные параметры и электрические характеристики
| Core | AVR |
| Core Size | 8-Bit |
| Max Clock Frequency | 8 MHz |
| Flash Memory | 32 KB (16K x 16) |
| SRAM | 2 KB |
| EEPROM | 1 KB |
| Operating Voltage Range | 2.7 V to 5.5 V (L version) |
| ADC Resolution | 10-bit |
| ADC Channels | 8 |
| Number of I/O | 32 |
| Timers | Two 8-bit, one 16-bit |
| Communication Interfaces | USART, SPI, I2C (TWI) |
| Debug Interface | JTAG (boundary-scan and on-chip debug) |
| Рабочая температура | -40C to +85C |
| Корпус | 40-PDIP |
| Тип монтажа | Through Hole |
| Program Memory Type | In-System Programmable (ISP) Flash, read-while-write |
Конфигурация выводов ATMEGA32L-8PU
| Контакт 1 | PB0 — Port B bit 0 (XCK/Timer0 external clock) |
| Контакт 2 | PB1 — Port B bit 1 (T1) |
| Контакт 3 | PB2 — Port B bit 2 (AIN0/INT2) |
| Контакт 4 | PB3 — Port B bit 3 (AIN1/OC0 PWM output) |
| Контакт 5 | PB4 — Port B bit 4 (SPI Slave Select) |
| Контакт 6 | PB5 — Port B bit 5 (SPI Master Output / Slave Input - MOSI) |
| Контакт 7 | PB6 — Port B bit 6 (SPI Master Input / Slave Output - MISO) |
| Контакт 8 | PB7 — Port B bit 7 (SPI Clock / OC2 PWM output) |
| Контакт 9 | RESET — Active-low reset input (internal pull-up) |
| Контакт 10 | VCC — Digital supply voltage (2.7 V to 5.5 V) |
| Контакт 11 | GND — Ground |
| Контакт 12 | XTAL2 — Inverting oscillator amplifier output / external clock input |
| Контакт 13 | XTAL1 — Inverting oscillator amplifier input |
| Контакт 14 | PD0 — Port D bit 0 (USART RXD) |
| Контакт 15 | PD1 — Port D bit 1 (USART TXD) |
| Контакт 16 | PD2 — Port D bit 2 (External interrupt INT0) |
| Контакт 17 | PD3 — Port D bit 3 (External interrupt INT1) |
| Контакт 18 | PD4 — Port D bit 4 (Timer1 output compare OC1B) |
| Контакт 19 | PD5 — Port D bit 5 (Timer1 output compare OC1A) |
| Контакт 20 | PD6 — Port D bit 6 (Timer1 input capture ICP1) |
| Контакт 21 | PD7 — Port D bit 7 (Timer2 output compare OC2) |
| Контакт 22 | PC0 — Port C bit 0 (TWI SCL / JTAG TCK) |
| Контакт 23 | PC1 — Port C bit 1 (TWI SDA / JTAG TMS) |
| Контакт 24 | PC2 — Port C bit 2 (JTAG TDO) |
| Контакт 25 | PC3 — Port C bit 3 (JTAG TDI) |
| Контакт 26 | PC4 — Port C bit 4 (JTAG TCK alternate function) |
| Контакт 27 | PC5 — Port C bit 5 (JTAG TMS alternate function) |
| Контакт 28 | PC6 — Port C bit 6 (JTAG TDI alternate function / Timer oscillator TOSC1) |
| Контакт 29 | PC7 — Port C bit 7 (JTAG TDO alternate function / TOSC2) |
| Контакт 30 | PA0 — Port A bit 0 (ADC channel 0) |
| Контакт 31 | PA1 — Port A bit 1 (ADC channel 1) |
| Контакт 32 | PA2 — Port A bit 2 (ADC channel 2) |
| Контакт 33 | PA3 — Port A bit 3 (ADC channel 3) |
| Контакт 34 | PA4 — Port A bit 4 (ADC channel 4) |
| Контакт 35 | PA5 — Port A bit 5 (ADC channel 5) |
| Контакт 36 | PA6 — Port A bit 6 (ADC channel 6) |
| Контакт 37 | PA7 — Port A bit 7 (ADC channel 7) |
| Контакт 38 | AREF — Analog reference voltage for ADC |
| Контакт 39 | GND — Ground |
| Контакт 40 | AVCC — Analog supply voltage for Port A and ADC |
Типичное применение
ATMEGA32L-8PU подходит для 6 применениеs: Education and Prototyping, Battery-Powered Sensor Nodes, Industrial Control and Automation, Hobby Robotics, Embedded Instrumentation and Dataloggers, Building Automation and Smart Home Nodes.
Education and Prototyping
The ATMEGA32L-8PU is a staple of university embedded-systems courses and hobbyist projects because the 40-pin PDIP through-hole package plugs directly into breadboards and can be hand-soldered or replaced without hot-air equipment. Its 2.7 V to 5.5 V supply range tolerates miswired supplies, and the on-chip calibrated RC oscillator at 8 MHz removes the need for an external crystal in simple experiments, reducing the bill of materials to the MCU plus decoupling. The 32 KB Flash and 2 KB SRAM leave generous headroom for complex student assignments such as RTOS demos or multi-peripheral labs, while the free AVR-GCC toolchain and low-cost USBasp ISP programmers keep total per-student cost minimal. Read-while-write ISP Flash supports rapid code iteration without removing the chip.
Рекомендуется
Battery-Powered Sensor Nodes
The low-voltage L-grade operation from 2.7 V to 5.5 V and six software-selectable sleep modes make the ATMEGA32L-8PU a strong fit for battery-operated sensing nodes. In Power-down mode the core is stopped and wake-up is available from external interrupts, TWI address match, or watchdog, drawing microamp-level current per the manufacturer datasheet, while Power-save mode keeps the asynchronous timer alive for periodic wake-ups from an RTC. The 8-channel 10-bit ADC with differential inputs and 1x/10x/200x programmable gain digitizes bridge and thermocouple signals directly, and the 1 KB EEPROM stores calibration coefficients across battery swaps. Designers should budget wake-up latency and use the ADC Noise Reduction mode when sampling at low supply voltages.
Рекомендуется
Industrial Control and Automation
With an extended industrial operating range of -40C to +85C, brown-out detection, watchdog timer, and JTAG boundary-scan on the port-C pins, the ATMEGA32L-8PU addresses a broad class of industrial control tasks such as panel controllers, valve drivers, and small PLC logic modules. The two 8-bit and one 16-bit timer/counters deliver PWM outputs (OC0, OC1A/OC1B, OC2) for motor or heater control, the USART handles Modbus-RTU framing at standard baud rates, and the TWI (I2C) master links expansion I/O and sensors. At 8 MHz the core sustains up to 8 MIPS, adequate for closed-loop control at kilohertz rates. The PDIP socket mounting allows field firmware updates by chip swap in maintenance environments.
Рекомендуется
Hobby Robotics
Robotics builders favor the ATMEGA32L-8PU for the same reasons as educational users - socketed PDIP convenience plus generous I/O count of 32 lines, enough to drive four motor channels with direction and PWM, several range sensors, and a servo bank simultaneously. The 16-bit Timer/Counter1 generates high-resolution servo PWM, Timer0/Timer2 provide fast PWM for DC motor speed control via driver ICs, and the analog comparator plus 10-bit ADC read line-following photoreflector arrays directly. At 5 V the I/O pins source up to 20 mA per the datasheet, sufficient for LEDs and small loads. The 2 KB SRAM accommodates odometry state, kinematics, and communications buffers that exceed the capacity of smaller ATmega8-class parts.
Рекомендуется
Embedded Instrumentation and Dataloggers
For bench and field instrumentation, the ATMEGA32L-8PU pairs its 8-channel 10-bit ADC (up to 15 kSPS at full resolution, with differential mode and 200x gain for small signals) with 32 KB of Flash that holds logging firmware, data tables, and a bootloader. The USART streams records to a PC or radio modem, the TWI bus attaches RTC and precision sensor ICs, and the 1 KB EEPROM keeps configuration intact through power cycling. The wide 2.7 V to 5.5 V range allows direct operation from two or three cell battery stacks, while the ADC Noise Reduction sleep mode reduces conversion noise by stopping the CPU during sampling - a documented technique in the manufacturer datasheet for maximizing effective resolution.
Рекомендуется
Building Automation and Smart Home Nodes
Smart-building nodes benefit from the ATMEGA32L-8PU's communication portfolio: TWI for on-board sensors, SPI for RF transceiver modules, and USART for RS-485 field buses after level conversion. The 32 I/O lines cover keypads, LCD interfaces (4-bit and 8-bit modes), relays, and triac drivers simultaneously in one MCU, replacing multi-chip glue designs. Six sleep modes and the low-voltage 2.7 V minimum allow wall-powered nodes to meet standby-power expectations by dropping into Power-down between events, waking on pin-change interrupts from PIR sensors or keypads. JTAG on-chip debug accelerates firmware bring-up across the building portfolio, and lock bits protect deployed code from unauthorized reads during maintenance.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для ATMEGA32L-8PU — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | ATMEGA32A-PU | ATMEGA32A-PN | ATMEGA32L-8AC | ATMEGA16L-8PU |
|---|---|---|---|---|---|
| Package | 40-PDIP | 40-PDIP - same | 40-PDIP - same | TQFP-44 (SMD) | 40-PDIP - same |
| Brand | Microchip Technology (Atmel) | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Flash Memory | 32 KB | 32 KB | 32 KB | 32 KB | 16 KB |
| SRAM | 2 KB | 2 KB | 2 KB | 2 KB | 1 KB |
| Max Clock Frequency | 8 MHz | 16 MHz | 16 MHz | 8 MHz | 8 MHz |
| Operating Voltage | 2.7 V to 5.5 V | 4.5 V to 5.5 V | 4.5 V to 5.5 V | 2.7 V to 5.5 V | 2.7 V to 5.5 V |
| EEPROM | 1 KB | 1 KB | 1 KB | 1 KB | 0.5 KB |
Ключевые отличия
- 3.3 V capable low-voltage grade (против ATMEGA32A-PU)
- Double the memory of the next pin-compatible sibling (против ATMEGA16L-8PU)
- Through-hole DIP-40 convenience vs SMD variants (против ATMEGA32L-8AC)
Заметки по проектированию
Decouple VCC (pin 10) and AVCC (pin 40) separately with 100 nF ceramic capacitors placed within 10 mm of each pin, plus a 10 uF bulk capacitor near the supply entry. AVCC must be connected to VCC even when the ADC is unused, or through an LC filter (10 uH + 100 nF) when ADC accuracy matters. Keep the analog ground return for AREF (pin 38) quiet: route the ADC reference path away from digital switching currents. If using the internal 2.56 V reference, add a 100 nF capacitor on AREF to stabilize it during conversions.
Three fuse pitfalls trap designers on the ATmega32: (1) JTAG is enabled by default on port C pins PC2-PC7, hijacking them as GPIO - disable via the JTAGEN fuse if you need all eight port C pins. (2) Setting SPIEN with an external clock absent, or misprogramming CKSEL/CKOPT fuses, can effectively 'brick' a chip to the point where only a parallel/high-voltage programmer recovers it. (3) The brown-out detector threshold must match your voltage domain - at 3.3 V operation the 4.0 V BOD level would cause constant resets. Verify all fuse settings in Microchip Studio before burning.
For socketed PDIP prototypes, keep crystal wiring short (under 20 mm traces) between XTAL1/XTAL2 and ground the crystal case locally; long stubs cause erratic startup, especially below 3.3 V where oscillator margin shrinks. When migrating to the SMD TQFP-44 siblings (ATMEGA32L-8AI/AC), place the 44-pin footprint to also accept the MLF variant if future options matter. Route the RESET net with a 10 kOhm pull-up and space for a programming connector (MOSI/MISO/SCK/RESET) so ISP remains possible after final assembly.
Информация о соответствии
RoHS-compliant lead-free PDIP per distributor listings (DigiKey, Mouser, LCSC). Not AEC-Q100 qualified; Microchip offers ATMEGA32C1 automotive variants for vehicle applications.
