ATMEGA32L-8PU - 8-bit AVR MCU 32KB 8MHz DIP-40 | Microchip
MPN: ATMEGA32L-8PU ✓ פעילATMEGA32L-8PU סקירה
A microcontroller (MCU) is a single integrated circuit that combines a processor core, program memory, data memory, and peripheral functions such as timers, UARTs, and ADCs into one chip. Within the embedded-systems hierarchy, the ATmega32 family sits in the 8-bit general-purpose MCU class, positioned between smaller ATmega8/16 devices and higher-performance AVR or ARM-based controllers. The AVR architecture uses a Harvard design with 32 general-purpose working registers directly connected to the ALU, executing most instructions in a single clock cycle - up to 8 MIPS throughput at 8 MHz.
Key features include 32 KB ISP Flash with read-while-write capability, a JTAG interface for boundary-scan and on-chip debugging, three flexible timer/counters (two 8-bit, one 16-bit with PWM), a byte-oriented two-wire serial (I2C-compatible) interface, an 8-channel 10-bit ADC with differential mode and programmable gain, and a programmable serial USART. The low-voltage 'L' variant operates from 2.7 V to 5.5 V, enabling 3.3 V battery-powered designs.
The ATMEGA32L-8PU supports six sleep modes (Idle, ADC Noise Reduction, Power-save, Power-down, Standby, Extended Standby) for aggressive power reduction, plus an on-chip RC oscillator, brown-out detection, and internal interrupt sources.
Typical applications include education and prototyping (the breadboard-friendly DIP-40 package), industrial sensor nodes, battery-powered instrumentation, and motor-control or building-automation controllers.
Design consideration: at 8 MHz the speed grade is derated below 4.5 V, so verify that your clock frequency and supply voltage combination is legal across the full operating temperature range.
This page synthesizes distributor pricing, drop-in alternatives within the ATmega family, pinout data, and practical design notes not found in a single manufacturer datasheet page.
חלופות תחליף ישיר עבור ATMEGA32L-8PU — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.
וריאנטים בסדרה זו
דגמים מאותה סדרה התואמים Drop-in עם ATMEGA32L-8PU (אותו גורם צורה וטביעת רגל) — שונים ב Package, Communication Interfaces, Operating Temperature, EEPROM, Debug Interface.
ATMEGA32A-PU
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←ATMEGA32A-PN
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←ATMEGA32L-8PI
✅ Drop-In ⚠️ מפרטים לא מאומתים📋 חלופה להתייחסות (לא בקטלוג)
ATMEGA32L-8AC
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←ATMEGA32L-8AI
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←ATMEGA16L-8PU
✅ Drop-In ⚠️ מפרטים לא מאומתיםצור קשר לקבלת מחיר
הצג גיליון נתונים ←ATMEGA32-16PU
✅ Drop-In ⚠️ מפרטים לא מאומתיםצור קשר לקבלת מחיר
הצג גיליון נתונים ←ATMEGA32L-8PU דירוגים מרביים ומאפיינים חשמליים
| Core | AVR |
| Core Size | 8-Bit |
| Max Clock Frequency | 8 MHz |
| Flash Memory | 32 KB (16K x 16) |
| SRAM | 2 KB |
| EEPROM | 1 KB |
| Operating Voltage Range | 2.7 V to 5.5 V (L version) |
| ADC Resolution | 10-bit |
| ADC Channels | 8 |
| Number of I/O | 32 |
| Timers | Two 8-bit, one 16-bit |
| Communication Interfaces | USART, SPI, I2C (TWI) |
| Debug Interface | JTAG (boundary-scan and on-chip debug) |
| טמפרטורת פעולה | -40C to +85C |
| מארז | 40-PDIP |
| סוג הרכבה | Through Hole |
| Program Memory Type | In-System Programmable (ISP) Flash, read-while-write |
תצורת פינים של ATMEGA32L-8PU
| פין 1 | PB0 — Port B bit 0 (XCK/Timer0 external clock) |
| פין 2 | PB1 — Port B bit 1 (T1) |
| פין 3 | PB2 — Port B bit 2 (AIN0/INT2) |
| פין 4 | PB3 — Port B bit 3 (AIN1/OC0 PWM output) |
| פין 5 | PB4 — Port B bit 4 (SPI Slave Select) |
| פין 6 | PB5 — Port B bit 5 (SPI Master Output / Slave Input - MOSI) |
| פין 7 | PB6 — Port B bit 6 (SPI Master Input / Slave Output - MISO) |
| פין 8 | PB7 — Port B bit 7 (SPI Clock / OC2 PWM output) |
| פין 9 | RESET — Active-low reset input (internal pull-up) |
| פין 10 | VCC — Digital supply voltage (2.7 V to 5.5 V) |
| פין 11 | GND — Ground |
| פין 12 | XTAL2 — Inverting oscillator amplifier output / external clock input |
| פין 13 | XTAL1 — Inverting oscillator amplifier input |
| פין 14 | PD0 — Port D bit 0 (USART RXD) |
| פין 15 | PD1 — Port D bit 1 (USART TXD) |
| פין 16 | PD2 — Port D bit 2 (External interrupt INT0) |
| פין 17 | PD3 — Port D bit 3 (External interrupt INT1) |
| פין 18 | PD4 — Port D bit 4 (Timer1 output compare OC1B) |
| פין 19 | PD5 — Port D bit 5 (Timer1 output compare OC1A) |
| פין 20 | PD6 — Port D bit 6 (Timer1 input capture ICP1) |
| פין 21 | PD7 — Port D bit 7 (Timer2 output compare OC2) |
| פין 22 | PC0 — Port C bit 0 (TWI SCL / JTAG TCK) |
| פין 23 | PC1 — Port C bit 1 (TWI SDA / JTAG TMS) |
| פין 24 | PC2 — Port C bit 2 (JTAG TDO) |
| פין 25 | PC3 — Port C bit 3 (JTAG TDI) |
| פין 26 | PC4 — Port C bit 4 (JTAG TCK alternate function) |
| פין 27 | PC5 — Port C bit 5 (JTAG TMS alternate function) |
| פין 28 | PC6 — Port C bit 6 (JTAG TDI alternate function / Timer oscillator TOSC1) |
| פין 29 | PC7 — Port C bit 7 (JTAG TDO alternate function / TOSC2) |
| פין 30 | PA0 — Port A bit 0 (ADC channel 0) |
| פין 31 | PA1 — Port A bit 1 (ADC channel 1) |
| פין 32 | PA2 — Port A bit 2 (ADC channel 2) |
| פין 33 | PA3 — Port A bit 3 (ADC channel 3) |
| פין 34 | PA4 — Port A bit 4 (ADC channel 4) |
| פין 35 | PA5 — Port A bit 5 (ADC channel 5) |
| פין 36 | PA6 — Port A bit 6 (ADC channel 6) |
| פין 37 | PA7 — Port A bit 7 (ADC channel 7) |
| פין 38 | AREF — Analog reference voltage for ADC |
| פין 39 | GND — Ground |
| פין 40 | AVCC — Analog supply voltage for Port A and ADC |
יישומים טיפוסיים
ATMEGA32L-8PU מתאים עבור 6 יישוםs: Education and Prototyping, Battery-Powered Sensor Nodes, Industrial Control and Automation, Hobby Robotics, Embedded Instrumentation and Dataloggers, Building Automation and Smart Home Nodes.
Education and Prototyping
The ATMEGA32L-8PU is a staple of university embedded-systems courses and hobbyist projects because the 40-pin PDIP through-hole package plugs directly into breadboards and can be hand-soldered or replaced without hot-air equipment. Its 2.7 V to 5.5 V supply range tolerates miswired supplies, and the on-chip calibrated RC oscillator at 8 MHz removes the need for an external crystal in simple experiments, reducing the bill of materials to the MCU plus decoupling. The 32 KB Flash and 2 KB SRAM leave generous headroom for complex student assignments such as RTOS demos or multi-peripheral labs, while the free AVR-GCC toolchain and low-cost USBasp ISP programmers keep total per-student cost minimal. Read-while-write ISP Flash supports rapid code iteration without removing the chip.
מומלץ
Battery-Powered Sensor Nodes
The low-voltage L-grade operation from 2.7 V to 5.5 V and six software-selectable sleep modes make the ATMEGA32L-8PU a strong fit for battery-operated sensing nodes. In Power-down mode the core is stopped and wake-up is available from external interrupts, TWI address match, or watchdog, drawing microamp-level current per the manufacturer datasheet, while Power-save mode keeps the asynchronous timer alive for periodic wake-ups from an RTC. The 8-channel 10-bit ADC with differential inputs and 1x/10x/200x programmable gain digitizes bridge and thermocouple signals directly, and the 1 KB EEPROM stores calibration coefficients across battery swaps. Designers should budget wake-up latency and use the ADC Noise Reduction mode when sampling at low supply voltages.
מומלץ
Industrial Control and Automation
With an extended industrial operating range of -40C to +85C, brown-out detection, watchdog timer, and JTAG boundary-scan on the port-C pins, the ATMEGA32L-8PU addresses a broad class of industrial control tasks such as panel controllers, valve drivers, and small PLC logic modules. The two 8-bit and one 16-bit timer/counters deliver PWM outputs (OC0, OC1A/OC1B, OC2) for motor or heater control, the USART handles Modbus-RTU framing at standard baud rates, and the TWI (I2C) master links expansion I/O and sensors. At 8 MHz the core sustains up to 8 MIPS, adequate for closed-loop control at kilohertz rates. The PDIP socket mounting allows field firmware updates by chip swap in maintenance environments.
מומלץ
Hobby Robotics
Robotics builders favor the ATMEGA32L-8PU for the same reasons as educational users - socketed PDIP convenience plus generous I/O count of 32 lines, enough to drive four motor channels with direction and PWM, several range sensors, and a servo bank simultaneously. The 16-bit Timer/Counter1 generates high-resolution servo PWM, Timer0/Timer2 provide fast PWM for DC motor speed control via driver ICs, and the analog comparator plus 10-bit ADC read line-following photoreflector arrays directly. At 5 V the I/O pins source up to 20 mA per the datasheet, sufficient for LEDs and small loads. The 2 KB SRAM accommodates odometry state, kinematics, and communications buffers that exceed the capacity of smaller ATmega8-class parts.
מומלץ
Embedded Instrumentation and Dataloggers
For bench and field instrumentation, the ATMEGA32L-8PU pairs its 8-channel 10-bit ADC (up to 15 kSPS at full resolution, with differential mode and 200x gain for small signals) with 32 KB of Flash that holds logging firmware, data tables, and a bootloader. The USART streams records to a PC or radio modem, the TWI bus attaches RTC and precision sensor ICs, and the 1 KB EEPROM keeps configuration intact through power cycling. The wide 2.7 V to 5.5 V range allows direct operation from two or three cell battery stacks, while the ADC Noise Reduction sleep mode reduces conversion noise by stopping the CPU during sampling - a documented technique in the manufacturer datasheet for maximizing effective resolution.
מומלץ
Building Automation and Smart Home Nodes
Smart-building nodes benefit from the ATMEGA32L-8PU's communication portfolio: TWI for on-board sensors, SPI for RF transceiver modules, and USART for RS-485 field buses after level conversion. The 32 I/O lines cover keypads, LCD interfaces (4-bit and 8-bit modes), relays, and triac drivers simultaneously in one MCU, replacing multi-chip glue designs. Six sleep modes and the low-voltage 2.7 V minimum allow wall-powered nodes to meet standby-power expectations by dropping into Power-down between events, waking on pin-change interrupts from PIR sensors or keypads. JTAG on-chip debug accelerates firmware bring-up across the building portfolio, and lock bits protect deployed code from unauthorized reads during maintenance.
מומלץ
סיכום מוצרים מומלצים
נתוני עזר הנדסיים עבור ATMEGA32L-8PU — השוואה, הנחיות תכנון ומידע על תאימות.
מדריך בחירה
השוואה עם חלופות
| פרמטר | מוצר זה | ATMEGA32A-PU | ATMEGA32A-PN | ATMEGA32L-8AC | ATMEGA16L-8PU |
|---|---|---|---|---|---|
| Package | 40-PDIP | 40-PDIP - same | 40-PDIP - same | TQFP-44 (SMD) | 40-PDIP - same |
| Brand | Microchip Technology (Atmel) | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Flash Memory | 32 KB | 32 KB | 32 KB | 32 KB | 16 KB |
| SRAM | 2 KB | 2 KB | 2 KB | 2 KB | 1 KB |
| Max Clock Frequency | 8 MHz | 16 MHz | 16 MHz | 8 MHz | 8 MHz |
| Operating Voltage | 2.7 V to 5.5 V | 4.5 V to 5.5 V | 4.5 V to 5.5 V | 2.7 V to 5.5 V | 2.7 V to 5.5 V |
| EEPROM | 1 KB | 1 KB | 1 KB | 1 KB | 0.5 KB |
מבדילים עיקריים
- 3.3 V capable low-voltage grade (לעומתATMEGA32A-PU)
- Double the memory of the next pin-compatible sibling (לעומתATMEGA16L-8PU)
- Through-hole DIP-40 convenience vs SMD variants (לעומתATMEGA32L-8AC)
הערות תכנון
Decouple VCC (pin 10) and AVCC (pin 40) separately with 100 nF ceramic capacitors placed within 10 mm of each pin, plus a 10 uF bulk capacitor near the supply entry. AVCC must be connected to VCC even when the ADC is unused, or through an LC filter (10 uH + 100 nF) when ADC accuracy matters. Keep the analog ground return for AREF (pin 38) quiet: route the ADC reference path away from digital switching currents. If using the internal 2.56 V reference, add a 100 nF capacitor on AREF to stabilize it during conversions.
Three fuse pitfalls trap designers on the ATmega32: (1) JTAG is enabled by default on port C pins PC2-PC7, hijacking them as GPIO - disable via the JTAGEN fuse if you need all eight port C pins. (2) Setting SPIEN with an external clock absent, or misprogramming CKSEL/CKOPT fuses, can effectively 'brick' a chip to the point where only a parallel/high-voltage programmer recovers it. (3) The brown-out detector threshold must match your voltage domain - at 3.3 V operation the 4.0 V BOD level would cause constant resets. Verify all fuse settings in Microchip Studio before burning.
For socketed PDIP prototypes, keep crystal wiring short (under 20 mm traces) between XTAL1/XTAL2 and ground the crystal case locally; long stubs cause erratic startup, especially below 3.3 V where oscillator margin shrinks. When migrating to the SMD TQFP-44 siblings (ATMEGA32L-8AI/AC), place the 44-pin footprint to also accept the MLF variant if future options matter. Route the RESET net with a 10 kOhm pull-up and space for a programming connector (MOSI/MISO/SCK/RESET) so ISP remains possible after final assembly.
מידע על תאימות
RoHS-compliant lead-free PDIP per distributor listings (DigiKey, Mouser, LCSC). Not AEC-Q100 qualified; Microchip offers ATMEGA32C1 automotive variants for vehicle applications.
