DG411DYZ - Quad 35Ohm SPST Analog Switch | Renesas Electronics
Артикул: DG411DYZ ✓ АктивенDG411DYZ Обзор
An analog switch is an integrated semiconductor device that routes or isolates signals under digital control. The DG411 belongs to the analog-switch hierarchy, which includes CMOS analog switches, multiplexers, and demultiplexers. Each of its four SPST channels connects one analog source and drain when the associated control input activates it, allowing one IC to manage four separate signal paths.
The DG411DYZ provides low on-state resistance of 35 ohms, fast switching performance, and closely matched channel resistance. Manufacturer specifications indicate that on-resistance matching between switches is limited to 3 ohms maximum, while on-resistance flatness across the signal range is limited to 4 ohms maximum. These characteristics reduce signal-dependent distortion when switching precision audio, video, instrumentation, or control signals.
The four switches are bilateral and can conduct AC or DC signals in either direction. TTL-compatible and CMOS-compatible control inputs simplify connection to common digital controllers. The manufacturer also positions the DG411 family as a drop-in replacement for the DG211 and DG212 families, providing a practical upgrade path for existing high-voltage switching designs while preserving the familiar 16-pin footprint.
Typical uses include audio and video routing, precision measurement systems, industrial signal multiplexing, data-acquisition front ends, and control systems requiring multiple independently switched analog paths. Its four normally closed channels are especially useful when a default connection must remain active until a control signal commands a transition.
Choose power-supply rails according to the manufacturer datasheet and ensure that input, control, and analog signals remain within their permitted voltage limits. Pay particular attention to supply sequencing and off-state isolation when the switch handles high-impedance sensors. Decoupling should be placed close to the supply pins, while sensitive analog routing should minimize parasitic capacitance and leakage paths.
This product page combines the DG411DYZ electrical characteristics, drop-in replacement considerations, comparison data, and practical layout guidance into a compact engineering reference for analog-signal routing designs.
Аналоги без доработки для DG411DYZ — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с DG411DYZ (тот же форм-фактор и посадочное место) — отличается по Number of Switches, Package, Mounting Type, Switch Configuration, On-Resistance Flatness.
DG411DY-E3
✅ Прямая заменаУточнить цену
Открыть даташит →DG411DY+T
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
DG411DY+T
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
DG411DYZ Максимальные параметры и электрические характеристики
| Number of Switches | 4 switches |
| Switch Configuration | 4 x SPST |
| Switch State | Normally closed |
| Maximum On-State Resistance | 35 ohm |
| Turn-On Time | 175 ns |
| Turn-Off Time | 145 ns |
| Supply Voltage Range | 5 V to 34 V |
| Analog Input Range | ±15 V |
| On-Resistance Matching Between Switches | 3 ohm maximum |
| On-Resistance Flatness | 4 ohm maximum |
| Signal Conductivity | Bidirectional for AC or DC signals |
| Logic Compatibility | TTL and CMOS compatible |
| Корпус | 16-pin SOIC |
| Тип монтажа | Surface mount |
Конфигурация выводов DG411DYZ
| Контакт 1 | V+ — Positive power supply |
| Контакт 2 | S1 — Control input for switch 1 |
| Контакт 3 | D1 — Drain terminal for switch 1 |
| Контакт 4 | V- — Negative power supply |
| Контакт 5 | S2 — Control input for switch 2 |
| Контакт 6 | D2 — Drain terminal for switch 2 |
| Контакт 7 | S3 — Control input for switch 3 |
| Контакт 8 | D3 — Drain terminal for switch 3 |
| Контакт 9 | D4 — Drain terminal for switch 4 |
| Контакт 10 | S4 — Control input for switch 4 |
| Контакт 11 | V- — Negative power supply |
| Контакт 12 | GND — Ground connection |
| Контакт 13 | V+ — Positive power supply |
| Контакт 14 | V- — Negative power supply |
| Контакт 15 | GND — Ground connection |
| Контакт 16 | V+ — Positive power supply |
Типичное применение
DG411DYZ подходит для 6 применениеs: Precision Audio Signal Routing, Video Signal Multiplexing, Industrial Sensor Acquisition, Data Acquisition Front End, Test and Measurement Switching, Embedded Control Signal Isolation.
Precision Audio Signal Routing
The DG411DYZ fits precision audio routing because each of its four normally closed SPST channels has a maximum on-state resistance of 35 ohm. Matching between switches is specified at 3 ohm maximum, helping reduce channel-dependent gain variation when multiple sources feed a common audio path. Its bidirectional conduction also permits AC signals to flow in either direction. The device can remain connected during normal operation and disconnect a channel when its control input changes state. Engineers should keep analog traces short, maintain a continuous ground reference, and check that the signal amplitude remains within the stated ±15 V analog range.
Рекомендуется
Video Signal Multiplexing
The DG411DYZ can route multiple video or control signals through four independent, normally closed channels in a compact 16-pin SOIC. The 35-ohm maximum on-resistance provides a practical starting point for low-impedance video routing, while 3-ohm maximum resistance matching helps maintain consistency between selected sources. Fast 175 ns and 145 ns switching times support prompt source changes without requiring a large discrete-switch network. PCB implementation should minimize trace capacitance, keep the analog ground plane continuous, and place any termination components directly at the receiving device.
Рекомендуется
Industrial Sensor Acquisition
The DG411DYZ is suitable for multiplexing industrial sensor lines through four independent normally closed channels. Its TTL- and CMOS-compatible controls permit direct use with common controller logic, while bilateral operation supports sensors that source or sink the selected signal. The 35-ohm maximum on-resistance can be evaluated against the sensor output impedance and acquisition-device input impedance before selection. Designers should account for leakage, off-state isolation, and switch capacitance when using high-impedance sensors, and verify that industrial temperature and supply requirements are satisfied by the exact DG411 ordering suffix.
Рекомендуется
Data Acquisition Front End
The DG411DYZ can place four sensor or test signals into a shared data-acquisition path using its four SPST channels. Fast switching times of 175 ns turn-on and 145 ns turn-off reduce dead time during channel changes, while low resistance matching supports repeatable source selection. Because the channels are normally closed, the selected signal remains connected until an active control command transfers it. Place the switch close to the multiplexer node when source impedance is high, provide a low-impedance reference return, and include anti-aliasing components after the switching node to control sampling transients.
Рекомендуется
Test and Measurement Switching
The DG411DYZ provides four independently switchable paths for test fixtures, instrument routing, and programmable signal connections. Its normally closed configuration creates a defined default state, which is useful when a measurement path must remain connected during reset or power-up. Maximum on-resistance of 35 ohm and resistance matching of 3 ohm should be included in the measurement-budget calculation. Layout should use short traces and guard spacing from fast digital controls, while grounding practices should prevent injected control current from appearing as an input error.
Рекомендуется
Embedded Control Signal Isolation
The DG411DYZ can isolate four external control or analog lines under firmware control. Because each SPST channel operates independently, one command can disconnect an actuator or sensor while the other three remain active. The fast 145 ns turn-off time supports rapid deactivation, and the TTL- and CMOS-compatible logic inputs simplify sequencing. Designers should not treat the 35-ohm path as a zero-ohm conductor; include resistance in actuator drive calculations and verify current, voltage, and power limits against the complete manufacturer electrical characteristics.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для DG411DYZ — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | DG411DY | DG411DY+T | DG411DY+T |
|---|---|---|---|---|
| Brand | Renesas Electronics | Renesas Electronics | Renesas Electronics | Analog Devices |
| Package | 16-pin SOIC | 16-pin SOIC | 16-pin SOIC | 16-pin SOIC |
| Number of Circuits | 4 | 4 | 4 | 4 |
| Switch Configuration | 1:1 SPST | DG411 quad-SPST family | 1:1 SPST | 1:1 SPST |
| Normal Switch State | Normally closed | Normally closed | Normally closed | Normally closed |
Ключевые отличия
- Lower maximum on-state resistance (против DG411DY+T)
- Faster specified switching response (против DG411DY)
- Documented channel matching and flatness (против DG411DY+T)
Заметки по проектированию
Route each analog source and drain trace as short as practical, especially when driving a high-impedance sensor or measurement input. Place the DG411DYZ near the shared switching node rather than midway between distant sources and receivers. Keep the ground plane continuous beneath the SOIC and avoid splitting return paths between analog and control sections, since inductive coupling can appear as a false input signal.
Include the maximum 35-ohm on-state resistance and the control-dependent charge injection in the signal-error budget. For low-frequency precision measurements, compare the resulting divider error with the acquisition input impedance and add any required termination directly at the receiving input. For fast signals, keep control traces away from sensitive analog nodes and use a continuous reference plane to reduce crosstalk during the 175 ns turn-on and 145 ns turn-off transitions.
Connect the positive, negative, and ground pins according to the pin configuration in the manufacturer datasheet. Decoupling capacitors should be placed close to the relevant supply pins with short ground returns. Do not assume that the analog signal can exceed the device's absolute maximum ratings merely because the selected switch path is open; verify supply, control-input, and signal-pin limits before power-up and hot-plug testing.
Информация о соответствии
The DG411 is an interface IC rather than an automotive-qualified device. Compliance attributes require confirmation for the exact DG411DYZ ordering code and manufacturing status.