LM2902AWYDT - Quad 1.3MHz Op Amp, 14-SO | STMicroelectronics
Артикул: LM2902AWYDT ✓ АктивенLM2902AWYDT Обзор
An operational amplifier, or op amp, is an analog integrated circuit that amplifies the voltage difference between its non-inverting and inverting inputs. The quad configuration integrates four independent amplifiers into one 14-SO package. Internal frequency compensation simplifies closed-loop design, while a common power architecture allows the four amplifiers to operate from a single supply over a wide voltage range. The LM2902 family therefore provides more functional density than discrete single amplifiers and reduces the number of components needed for multi-channel analog circuits.
Key electrical characteristics include a 1.3 MHz gain-bandwidth product, 100 dB typical gain, approximately 375 uA supply current per amplifier, 20 nA input bias current, 2 nA input offset current, and 800 V input differential voltage capability. These characteristics support general-purpose applications where low power, usable bandwidth, and moderate input precision are more important than high-speed or precision amplifier performance.
The device uses four independent operational amplifiers with internally implemented frequency compensation. Its push-pull output stage supports output-current demands commonly encountered in buffer, comparator-style, and analog-control circuits. The operating approach is suited to single-supply systems, where an amplifier may operate from an input and output signal referenced to the same supply rail rather than requiring a symmetrical positive and negative supply.
Typical uses include industrial process-control loops, automotive interface circuits, sensor conditioning, current-to-voltage conversion, low-frequency active filters, and general signal amplification. The four amplifiers can process related channels or provide separate functions such as amplification, filtering, thresholding, and buffering on one PCB. For designs requiring more precision or bandwidth, the device should be compared against the corresponding performance limits before compensation, noise, or offset requirements are finalized.
Layout should preserve short feedback paths, maintain suitable grounding, and place input and output decoupling close to the device. Because this is a general-purpose quad amplifier, stability is commonly established with the manufacturer's recommended compensation approach and output isolation resistors where capacitive loading requires them. Verify input and output common-mode limits, supply voltage, load current, and thermal conditions against the manufacturer datasheet before releasing the circuit.
This product record combines the LM2902AWYDT device identity, package information, principal electrical characteristics, sourcing context, and verified drop-in alternatives. It also adds practical guidance for comparing the STMicroelectronics LM2902 family with pin-compatible single-supply quad amplifiers from Texas Instruments and NXP Semiconductors.
Аналоги без доработки для LM2902AWYDT — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с LM2902AWYDT (тот же форм-фактор и посадочное место) — отличается по Package, RoHS Status, Number of Amplifier Channels, Supply Configuration, Amplifier Type.
LM2902WYDT
✅ Прямая заменаУточнить цену
Открыть даташит →LM2902AWYD
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
LM2902DTB
✅ Прямая заменаУточнить цену
Открыть даташит →LM2902D
✅ Прямая заменаУточнить цену
Открыть даташит →LM2902DR
✅ Прямая заменаУточнить цену
Открыть даташит →LM2902AWYDT Максимальные параметры и электрические характеристики
| Amplifier Type | General-purpose operational amplifier |
| Number of Amplifiers | 4 amplifiers |
| Gain-Bandwidth Product | 1.3 MHz |
| Open-Loop Gain | 100 dB |
| Ток потребления | 375 uA |
| Input Bias Current | 20 nA |
| Input Offset Current | 2 nA |
| Input Differential Voltage | 800 V |
| Compensation | Internal frequency compensation |
| Supply Type | Single supply |
| Корпус | 14-SO |
| Число выводов | 14 pins |
| Тип монтажа | Surface mount |
| Тип выхода | Push-pull |
| Статус RoHS | Compliant |
Руководство по цоколевке LM2902AWYDT в корпусе 14-so
Цоколевка для LM2902AWYDT (корпус 14-so). Этот аналоговый компонент имеет выводы входа, выхода и питания. Обратитесь к техническому описанию производителя для конфигураций выводов балансировки нуля, коррекции и разрешения. Идеально подходит для схем обработки сигналов и усилителей.
Нет подробных данных о распиновке для LM2902AWYDT.
Обратитесь к даташиту для полной конфигурации выводов.
Типичное применение
LM2902AWYDT подходит для 6 применениеs: Industrial Sensor Conditioning, Automotive Interface Circuits, Active Audio Filtering, Current-to-Voltage Conversion, Power Supply Feedback Control, Portable Instrumentation.
Industrial Sensor Conditioning
The LM2902AWYDT fits multichannel industrial sensor conditioning because its four independent, internally compensated amplifiers can amplify, filter, and buffer several related signals in one 14-SO package. The 1.3 MHz gain-bandwidth product is adequate for many low-frequency pressure, temperature, and position sensors, while approximately 375 uA supply current per amplifier supports low-power measurement modules. Each channel can implement a non-inverting or inverting stage according to the sensor impedance and signal level. Confirm the input common-mode range against the selected sensor output, and keep feedback loops short to maintain stability. The quad configuration reduces package count and helps simplify routing when several conditioned signals must be digitized by a downstream controller.
Рекомендуется
Automotive Interface Circuits
The LM2902AWYDT is suitable for low-frequency automotive interface circuits that require multiple general-purpose amplifiers on a single supply. Its four independent channels can support sensor buffering, threshold generation, error amplification, and actuator-signal conditioning, while the 1.3 MHz gain-bandwidth product is sufficient for many slow control and body-electronics functions. The A-series ordering code is intended for automotive-oriented use, but engineers should verify the exact AEC-Q100 qualification, temperature grade, and electrical limits in the STMicroelectronics datasheet. Automotive designs should also include transient protection, input clamping, grounding, and load-disconnect analysis appropriate to the vehicle environment.
Рекомендуется
Active Audio Filtering
The LM2902AWYDT can implement low-frequency active filters in audio preamplifier, mixer, or equalizer circuitry when four related channels are required. Its 1.3 MHz gain-bandwidth product provides more bandwidth than is normally needed for voice-band and low-frequency music shaping, while the four integrated amplifiers allow separate stages for input amplification, equalization, mixing, and output buffering. General-purpose performance means it should not be selected for demanding low-noise headphone paths without checking noise, offset, and distortion requirements. Keep filter resistors and capacitors close to their associated op-amp pins, maintain a practical grounding topology, and isolate capacitive loads with series resistors when required by the stability analysis.
Рекомендуется
Current-to-Voltage Conversion
The LM2902AWYDT is useful for converting a sensor or shunt current into a measurable voltage because its four amplifiers can provide instrumentation and active filtering functions around a single current-to-voltage stage. The 20 nA input bias current and 2 nA input offset current figures are especially relevant when the source impedance is high, since input-referred errors can otherwise distort the converted signal. The 1.3 MHz bandwidth is ample for many slow measurement loops and helps limit the noise bandwidth of subsequent filtering. Select feedback and balance resistors with suitable ratios and tolerances, keep the input node physically short, and verify that common-mode and output-swing requirements fit the selected supply voltage.
Рекомендуется
Power Supply Feedback Control
The LM2902AWYDT can support low-frequency power-supply feedback, error amplification, and slow-loop control functions where four amplifiers allow the design to combine sensing, error amplification, filtering, and auxiliary buffering. Its internally compensated topology and 1.3 MHz gain-bandwidth product are compatible with control loops considerably slower than switching frequencies, reducing the likelihood of excessive phase lag. The approximately 375 uA supply current is also useful in low-power regulation stages. Compensation must be derived from the plant and the selected amplifier’s open-loop response rather than copied without accounting for crossover, load, and output-stage differences. Stable layout requires a quiet reference ground, short feedback routing, and separation from high-current switching paths.
Рекомендуется
Portable Instrumentation
The low-power characteristics of the LM2902AWYDT make it useful in portable test and measurement equipment that needs several analog channels without allocating a separate package to every amplifier. Four independent channels can process sensor inputs, generate reference signals, buffer ADC drivers, and perform local diagnostics. With a 1.3 MHz gain-bandwidth product, the device is most appropriate for measurements in the audio, control, and low-frequency instrumentation bands rather than wideband oscilloscope front ends. Battery-operated designs should account for total supply current across all four amplifiers and inactive-channel states. Precision requirements should be checked against the input offset and bias-current figures, while PCB design should minimize thermal gradients and ground-current coupling.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для LM2902AWYDT — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | LM2902WYDT | LM2902AWYD | LM2902DT | LM2902D | LM2902DR |
|---|---|---|---|---|---|---|
| Package | 14-SO | 14-SO | 14-SO | 14-SO | 14-SOIC | 14-SO |
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics | Texas Instruments | NXP Semiconductors |
| Number of Amplifiers | 4 | 4 | 4 | 4 | 4 | 4 |
| Amplifier Type | General-purpose operational amplifier | General-purpose operational amplifier | General-purpose operational amplifier | General-purpose operational amplifier | General-purpose operational amplifier | General-purpose operational amplifier |
Ключевые отличия
- Automotive-oriented ordering code within a well-known quad amplifier family (против LM2902WYDT)
- Four independent general-purpose amplifiers in one package (против LM2902D)
- Single-supply operation with internal frequency compensation (против LM2902DR)
Заметки по проектированию
Place the bypass capacitor and the amplifier pins carrying high-frequency current close together, especially when the LM2902AWYDT supplies signals through long PCB traces. Keep each feedback loop compact and route it away from power-switching nodes and inductors. Use a continuous ground reference under the device when the board layout permits, but follow the manufacturer package drawing for exposed-pad or lead-frame grounding requirements. A single-supply circuit should share the analog and return paths carefully to avoid injecting supply ripple into the signal reference.
Do not assume that every LM2902 suffix has identical temperature or qualification requirements. The LM2902AWYDT includes an A-series ordering code, while LM2902WYDT, LM2902AWYD, LM2902DT, Texas Instruments LM2902D, and NXP LM2902DR can differ in grade or manufacturer-specific limits. Before substitution, compare supply range, common-mode range, output swing, offset, bias current, bandwidth, temperature rating, and automotive qualification. The shared 14-pin package establishes a physical starting point, not complete electrical equivalence.
Use short, direct input routes for high-impedance sensor nodes because the listed 20 nA input bias current and 2 nA input offset current can create meaningful errors when source resistance is high. Add a small protection or bias network at exposed inputs only after checking its effect on noise and bandwidth. For capacitive loads, evaluate stability using the recommended output isolation resistor and account for the added voltage drop. The 1.3 MHz gain-bandwidth product should be compared with the intended noise-gain curve rather than treated as a fixed closed-loop bandwidth.
Estimated: at a 12 V supply and approximately 375 uA supply current per amplifier, one active LM2902AWYDT amplifier dissipates about 4.5 mW, and four active amplifiers dissipate about 18 mW before output-current losses. The calculation uses 12 V and 375 uA per amplifier. Actual consumption rises with output current, so verify all four channels, output loads, supply tolerance, and temperature rise during worst-case operation.
Информация о соответствии
The LCSC product listing identifies LM2902AWYDT as RoHS compliant. Other compliance declarations and the exact automotive qualification status require confirmation from the manufacturer product documentation.