LM393BIPWR - Dual 38V Comparator | Texas Instruments
Артикул: LM393BIPWR ✓ АктивенLM393BIPWR Обзор
A differential comparator is an analog integrated circuit that compares two input voltages and produces a logic-level result indicating which input is higher. The LM393B family contains two independent comparators in one package. Within the power-management IC hierarchy, comparators occupy the interface between continuously varying sensor or analog signals and digital control systems. Their open-collector outputs can pull a logic rail low while permitting an external pull-up resistor to establish the high state.
The LM393B improves several characteristics of the original LM393 family. Its input offset voltage is specified at 0.37 mV, supporting more accurate decisions near the switching threshold. Input bias current of 3.5 nA limits the loading imposed on high-impedance sensors. A 200 µA supply current per comparator suits battery-operated and low-power systems, while the 1 µs response time supports practical control-loop and threshold-monitoring tasks. The common-mode range includes ground, which is important for single-supply sensing near 0 V.
Each comparator can operate from a single supply or split supplies. The differential input range is equal to the maximum-rated supply voltage of ±38 V according to the manufacturer product page. Because the outputs are open collector, two outputs can be tied together to create a wired-AND function. The output structure also provides flexibility for driving TTL, MOS, and CMOS loads when the pull-up supply and resistor are selected correctly.
Typical uses include overvoltage and undervoltage detection, window comparators, temperature sensing, industrial control thresholds, power-supply supervision, and sensor signal conditioning. In a power-supply application, the device can compare a feedback voltage with a reference and control an enable or protection signal. In a sensor interface, low bias current helps preserve the amplitude and accuracy of high-impedance signals. The commercial 0 °C to 85 °C temperature range and TSSOP-8 package suit compact industrial and consumer equipment.
Designers should use a pull-up resistor on each open-collector output, account for output sink-current limits, and ensure that input and output voltages remain within their respective absolute maximum ratings. Decoupling capacitance should be placed close to the supply pin, while sensitive analog inputs require short traces and minimal parasitic coupling. The B version is identified by Texas Instruments as a drop-in replacement for the LM293, LM393, and LM2903 families.
This product page combines manufacturer specifications, package and pin information, sourcing guidance, and application-focused engineering notes to support component selection and PCB implementation. It also distinguishes the commercial LM393BIPWR from temperature-range, family-version, and low-voltage alternatives that may appear in cross-reference searches.
Аналоги без доработки для LM393BIPWR — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с LM393BIPWR (тот же форм-фактор и посадочное место) — отличается по Comparator Type, Package, Output Type, Supply Current, Differential Input Voltage Range.
LM393PWRG3
✅ Прямая заменаУточнить цену
Открыть даташит →LM393APWR
✅ Прямая заменаУточнить цену
Открыть даташит →LM2903BIPWR
✅ Прямая замена ⚠️ Характеристики не провереныУточнить цену
Открыть даташит →LM393BIPWR-Q1
✅ Прямая замена ⚠️ Характеристики не проверены📋 Справочный аналог (нет в каталоге)
LMV393PWR
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
LM393BIPWR Максимальные параметры и электрические характеристики
| Comparator Type | Dual differential comparator |
| Тип выхода | Open-collector |
| Number of Comparators | 2 |
| Supply Voltage Range | 2 V to 36 V |
| Maximum Rated Voltage | 38 V |
| Differential Input Voltage Range | ±38 V |
| Input Offset Voltage | 0.37 mV |
| Input Bias Current | 3.5 nA |
| Ток потребления | 200 µA per comparator |
| Response Time | 1 µs |
| Common-Mode Input Voltage Range | Includes ground |
| Output Compatibility | TTL, MOS, and CMOS |
| ESD Rating | 2 kV HBM |
| Диапазон рабочих температур | -40 °C to +85 °C |
| Корпус | 8-pin TSSOP (PW) |
| Тип монтажа | Surface mount |
| RoHS Compliance | Compliant |
| Уровень MSL | MSL 1, 260 °C unlimited |
Конфигурация выводов LM393BIPWR
| Контакт 1 | OUT1 — Comparator 1 open-collector output |
| Контакт 2 | IN1- — Comparator 1 inverting input |
| Контакт 3 | IN1+ — Comparator 1 non-inverting input |
| Контакт 4 | GND — Ground reference |
| Контакт 5 | IN2+ — Comparator 2 non-inverting input |
| Контакт 6 | IN2- — Comparator 2 inverting input |
| Контакт 7 | OUT2 — Comparator 2 open-collector output |
| Контакт 8 | VCC — Positive supply voltage |
Типичное применение
LM393BIPWR подходит для 6 применениеs: Industrial Overvoltage Detection, Power-Supply Window Monitor, Temperature Sensor Thresholding, Battery-Powered Sensor Interface, Motor and Solenoid Threshold Control, General-Purpose Logic Interface.
Industrial Overvoltage Detection
The LM393BIPWR suits industrial supply-limit monitoring because one channel can compare a divided feedback voltage with a reference and assert an open-collector fault signal. Its 0.37 mV input offset improves threshold precision, while 3.5 nA input bias current limits loading on the divider. The 1 µs response time detects rail excursions quickly, and the ±38 V differential input range provides additional margin. Add a pull-up resistor on the open-collector output and verify the divider ratio, input common-mode range, and system fault-routing requirements.
Рекомендуется
Power-Supply Window Monitor
The two independent comparators in the LM393BIPWR can monitor upper and lower supply thresholds for a window-monitor circuit. Each output uses open-collector wired logic, allowing fault conditions to be combined without adding another logic gate. The 2 V to 36 V supply range covers many 5 V, 12 V, and 24 V industrial rails, while low 200 µA supply current per comparator limits overhead. The design should account for output sink current, pull-up voltage, reference accuracy, and the comparator’s input common-mode limits.
Рекомендуется
Temperature Sensor Thresholding
A temperature-sensor signal can be divided and compared with a voltage reference using one channel of the LM393BIPWR to generate a thermal alarm. The 3.5 nA input bias current is useful when the sensing divider has high impedance, and the 0.37 mV offset helps preserve threshold accuracy. The commercial -40 °C to +85 °C rating covers many industrial ambient conditions. Designers should evaluate sensor slope, hysteresis, resistor tolerances, and whether a pull-up is needed to translate the open-collector result into the alarm logic level.
Рекомендуется
Battery-Powered Sensor Interface
The LM393BIPWR can perform low-side threshold detection beside a battery-powered sensor because its supply current is 200 µA per comparator. Ground-referenced sensing is supported because the common-mode input range includes ground, and the 3.5 nA input bias current minimizes disturbance to high-impedance sensor networks. At a 5 V supply, the device can detect charging, discharge, or signal-presence events without continuous conversion. Keep the pull-up and leakage currents low enough that standby demand remains compatible with the battery budget.
Рекомендуется
Motor and Solenoid Threshold Control
The LM393BIPWR can compare a scaled motor or solenoid feedback voltage with a command threshold, providing a hardware interlock independent of a software controller. Its 1 µs response time supports rapid transition detection, and the wide differential input rating accommodates signal excursions associated with industrial environments when the individual pin ratings are respected. Use the open-collector output to drive an interlock or protection input through a pull-up. Verify noise immunity, switching transients, grounding, and the load’s current requirements before deployment.
Рекомендуется
General-Purpose Logic Interface
The LM393BIPWR can translate a slowly changing analog signal into a CMOS- or TTL-compatible threshold event using an open-collector output and external pull-up. Its 3.5 nA input bias current is beneficial when the driving source has high output impedance, while the 1 µs response time provides clear edge timing for control and monitoring. Select the pull-up rail and resistor to satisfy downstream rise-time and sink-current requirements. The open-collector structure also permits wired-AND connection, simplifying multi-fault aggregation without a dedicated logic package.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для LM393BIPWR — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | LM393PWR | LM393APWR | LM2903BIPWR | LM393BIPWR-Q1 | LMV393PWR |
|---|---|---|---|---|---|---|
| Package | TSSOP-8 (PW) | TSSOP-8 (PW) | TSSOP-8 (PW) | TSSOP-8 (PW) | TSSOP-8 (PW) | TSSOP-8 (PW) |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Comparator Count | 2 | 2 | 2 | 2 | 2 | 2 |
| Output Type | Open-collector | Open-collector | Open-collector | Open-collector | Open-collector | Open-collector |
Ключевые отличия
- Improved B-version threshold accuracy (против LM393PWR)
- Low loading for high-impedance sensing (против LM393APWR)
- Higher supply-voltage headroom than LMV393 (против LMV393PWR)
Заметки по проектированию
Every open-collector output requires an external pull-up resistor. Omitting the pull-up leaves the output unable to establish a valid high state. Select the pull-up supply to remain within the downstream device’s logic limits, and size the resistor for both the comparator sink-current rating and the required rise time. Two outputs may be tied together for wired-AND operation, but their combined sink current must not exceed the device rating.
Place the supply bypass capacitor close to pin 8 and route it to the ground reference with a short, low-impedance path. Keep the two inverting and two non-inverting input nets away from switching nodes and high-current return paths. Because the inputs are sensitive to small differential signals, use a quiet ground reference and avoid routing copper beneath the analog inputs where coupling could cause false threshold transitions.
Estimated: comparator supply dissipation is approximately 200 µA per comparator multiplied by the supply voltage, before input-output conduction loss and output sinking. At a 5 V supply, the two-channel supply-current contribution is about 1 mA, or 5 mW. Actual device dissipation also depends on output current because the open collector dissipates energy while sinking the pull-up current, so include that term when evaluating long-duration high-duty-cycle operation.
Do not treat the 38 V maximum rating as a recommended operating supply. The specified operating supply range is 2 V to 36 V, and the differential input range is ±38 V. Input common-mode and output voltages have separate constraints. Verify absolute-maximum conditions during fault analysis, including supply transients and input shorts, while maintaining normal operation within the recommended electrical limits.
Информация о соответствии
The manufacturer and product information identify the LM393BIPWR as RoHS compliant and RoHS3 compliant, with MSL 1 at 260 °C unlimited. Automotive qualification is not stated for the commercial LM393BIPWR.