Analog Devices

MAX3232ECTE+T - 1Mbps True RS-232 Transceiver | Analog Devices

Артикул: MAX3232ECTE+T ✓ Активен
3.0 V to 5.5 V Vdss 10 nA Id 16-pin TQFN with exposed pad, 5 mm x 5 mm Package
MOQ: 1 |

MAX3232ECTE+T Обзор

The Analog Devices MAX3232ECTE+T is a dual RS-232 transceiver with two drivers and two receivers, a 3.0 V to 5.5 V supply range, operation up to 1 Mbps, and 15 kV ESD protection. It is packaged in a 16-pin TQFN with an exposed pad, a 5 mm by 5 mm surface-mount package intended for compact RS-232 interface designs.

A true RS-232 transceiver is an interface IC that converts logic-level signals into RS-232 line levels and converts received RS-232 signals back into digital logic levels. MAX3232 belongs to the RS-232 transceiver hierarchy within interface ICs, where the dual charge-pump circuit supports the positive and negative voltage swings required by true RS-232. The MAX3232 family is identified by Analog Devices as pin, package, and functionally compatible with the industry-standard MAX232.

Key characteristics include a 3.0 V minimum operating supply, a 5.5 V maximum operating supply, and a data rate of up to 1 Mbps. The device integrates two line drivers and two line receivers. Its low-power design can operate from a 3.3 V system without a separate 5 V supply. The specified 15 kV ESD protection improves robustness on exposed serial connectors, although system-level grounding and cable design remain important.

Internally, the MAX3232 combines its dual charge pump, two transmit drivers, and two receive receivers in one interface device. The charge pump generates the voltage needed for RS-232 output levels, while the receivers include the signal-conditioning functions needed to reject noise and recover logic-level data. The exposed thermal pad supports heat transfer from the device, and the 5 mm by 5 mm package reduces board area compared with larger leaded and SOIC implementations.

Typical uses include industrial serial-port adapters, USB-to-RS-232 equipment, instrumentation interfaces, POS terminals, embedded control systems, and data-acquisition equipment. The 1 Mbps capability supports higher-rate legacy serial links while the 3.3 V supply operation simplifies integration with modern embedded controllers and FPGAs. Designers should still confirm signal levels, connector requirements, and cable length against the complete interface specification.

For a new layout, place the charge-pump capacitors and RS-232 interface components close to their associated pins. Keep the exposed pad connected to the ground plane on a multilayer board, use the recommended via pattern, and provide the interface connector with an appropriate chassis or signal-ground strategy. The MAX3232ECTE+T is supplied in tape-and-reel packaging for automated assembly.

This product page combines the manufacturer specifications, package details, verified lifecycle information, pin-compatible family alternatives, and application-specific design guidance. It also highlights the differences engineers should evaluate when moving between commercial and extended-temperature MAX3232 package variants.

Аналоги без доработки для MAX3232ECTE+T — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.

Варианты в этой серии

Модели той же серии, совместимые без доработки с MAX3232ECTE+T (тот же форм-фактор и посадочное место) — отличается по ESD Protection, Package, Interface Standard, Product Type.

Analog Devices
ESD Protection: ±15 kV IEC 61000-4-2 air-gap, ±15 kV HBM
Package: 16-pin SSOP (CAE)
Сравнить с MAX3232ECTE+T →
Analog Devices
ESD Protection: ±15 kV
Package: 16-pin TSSOP
Interface Standard: TIA/EIA-232-F
Сравнить с MAX3232ECTE+T →

MAX3232ECAE+T

✅ Прямая замена ⚠️ Характеристики не проверены
Analog Devices
📦 TQFN-16 with exposed pad, 5 mm x 5 mm
RS-232 Transceiver · 2 / 2 · RS-232 (EIA/TIA-232, V.28/V.24) · 3.0 V to 5.5 V · Up to 1 Mbps (250 kbps minimum guaranteed) · ±15 kV IEC 61000-4-2 air-gap, ±15 kV HBM · 10 nA (typ) · 0°C to +70°C (C grade)

Уточнить цену

Открыть даташит →

MAX3232EATE+T

✅ Прямая замена ⚠️ Характеристики не проверены
📦 TQFN-16 with exposed pad, 5 mm x 5 mm
Same 3.0 V to 5.5 V supply, 2/2 transceiver configuration, and 1 Mbps data rate; the ordering-code temperature grade differs

📋 Справочный аналог (нет в каталоге)

MAX3232ECTE+T Характеристики

Product Type RS-232 transceiver
Transceiver Configuration 2 transmitters and 2 receivers
Supply Voltage Range 3.0 V to 5.5 V
Maximum Data Rate 1 Mbps
Interface Standard True RS-232
ESD Protection 15 kV
Low-Power Shutdown Current 10 nA
Корпус 16-pin TQFN with exposed pad, 5 mm x 5 mm
Тип монтажа Surface mount
Packing Method Tape and reel
Диапазон рабочих температур 0 °C to 70 °C

Руководство по цоколевке MAX3232ECTE+T в корпусе 16-pin tqfn with exposed pad, 5 mm x 5 mm

Цоколевка для MAX3232ECTE+T (корпус 16-pin tqfn with exposed pad, 5 mm x 5 mm). Нумерация выводов, функции и схемы подключения определены в техническом описании производителя. Обратитесь к нему для точного посадочного места и рекомендаций по пайке.

Схема цоколевки корпуса 16-pin tqfn with exposed pad, 5 mm x 5 mm для MAX3232ECTE+T

Нет подробных данных о распиновке для MAX3232ECTE+T.

Обратитесь к даташиту для полной конфигурации выводов.

Типичное применение

MAX3232ECTE+T подходит для 6 применениеs: Industrial Serial-Port Adapters, POS Terminal and Retail Equipment, Data-Acquisition Instruments, Embedded Debug and Service Interfaces, USB-to-RS-232 Adapter, Security and Access-Control Equipment.

🏭

Industrial Serial-Port Adapters

The MAX3232ECTE+T fits industrial serial adapters that convert a 3.3 V or 5 V digital controller port into a true RS-232 connection. Its 3.0 V to 5.5 V operating range allows use with both embedded processors and FPGAs, while the two-driver, two-receiver configuration supports bidirectional console and control links. The 1 Mbps maximum data rate is useful for legacy equipment that operates above standard serial-port speeds. The 15 kV ESD protection strengthens the connector-facing interface, but it does not replace a suitable chassis-ground strategy or cable design. In a completed adapter, the digital-side signals connect to the logic controller while the driver and receiver pins connect through protection and signal-conditioning components to the DE-9 or equivalent RS-232 connector.

🖥️

POS Terminal and Retail Equipment

The MAX3232ECTE+T is appropriate for point-of-sale terminals and peripheral interfaces that retain a true RS-232 port. Two transmitters and two receivers provide balanced bidirectional connectivity, and the 1 Mbps capability offers headroom for service and data-transfer links operating above legacy throughput. Because the device accepts a 3.0 V minimum supply, it can operate directly from a 3.3 V retail controller without a separate 5 V rail. In a terminal design, maintain separation between the switching logic and connector-side routing, place charge-pump capacitors close to the IC, and connect the exposed pad to a low-impedance ground plane. The specified 0 °C to 70 °C range suits ordinary indoor terminal environments but must be reviewed for outdoor kiosks or unheated retail equipment.

🔧

Data-Acquisition Instruments

The MAX3232ECTE+T can connect a laboratory or industrial data-acquisition instrument to an RS-232 controller. Its 1 Mbps maximum rate supports faster instrument-control traffic than the common 115.2 kbit/s operating mode, while true RS-232 levels improve compatibility with legacy test equipment. The dual receiver arrangement allows status or handshake signals to be monitored alongside the primary data channel. Place the MAX3232 near the connector-side signal path, keep the exposed pad thermally and electrically connected to ground, and provide local charge-pump capacitors exactly as specified in the manufacturer data sheet. The 15 kV ESD rating helps protect against incidental cable transients, although instrument grounding and isolation determine the ultimate noise performance. A system using long cables should also include appropriate transient protection and verify the receiver thresholds against its installed voltage levels.

🧩

Embedded Debug and Service Interfaces

The MAX3232ECTE+T is useful for embedded debug adapters, configuration tools, and service ports that need a true RS-232 electrical interface beside a modern 3.3 V controller. Its minimum operating supply of 3.0 V simplifies integration with low-power processors, and the 1 Mbps capability supports higher-speed debug or bootloader traffic when the target software and cable permit it. The two transmitters and two receivers can carry data and hardware-control signals over one connector. Use short, controlled traces between the controller, MAX3232, and connector, and keep switching regulators and high-current return paths out of the interface region. The exposed pad should be soldered to a ground plane with the recommended thermal-via arrangement. Where field cables enter the enclosure, supplement the IC's 15 kV ESD protection with connector-level design controls appropriate for the installation environment.

🌐

USB-to-RS-232 Adapter

The MAX3232ECTE+T serves as the physical-layer interface in a USB-to-RS-232 adapter because it translates 3.3 V or 5 V logic into true RS-232 levels. A USB-to-serial controller operating at 3.3 V can pair directly with the transceiver's 3.0 V minimum supply, avoiding an unnecessary level shifter on the logic side. The 2/2 channel count supports data plus handshake or status signals, and the 1 Mbps capability allows modern USB-to-serial firmware to use elevated baud rates when the attached RS-232 equipment supports them. Keep the charge-pump switching nodes compact, route connector-side traces away from digital and power-converter nodes, and use a continuous ground reference. For a finished adapter, use the MAX3232 data sheet's capacitor values and exposed-pad via pattern to prevent startup, noise, or thermal problems.

🔒

Security and Access-Control Equipment

The MAX3232ECTE+T can support access-control readers, controllers, and service tools that communicate through an RS-232 link. The 15 kV ESD protection is particularly relevant where cables connect to frequently touched or exposed equipment, while true RS-232 levels maintain compatibility with established access-control panels. Its dual-driver, dual-receiver arrangement can carry a primary command channel and auxiliary status or handshake signals. The device should be positioned near the connector, with a short and direct return path to protect signal integrity. Do not rely on the MAX3232 alone as a complete surge-protection strategy; add appropriately rated protection when the installation can experience severe transients. For access-control hardware located outside controlled temperature ranges, select an extended-temperature MAX3232E grade and verify the final qualification requirements before manufacturing.

What is the MAX3232ECTE+T?
The MAX3232ECTE+T is a dual true-RS-232 transceiver with two drivers, two receivers, a 3.0 V to 5.5 V supply range, and operation up to 1 Mbps. According to the Analog Devices MAX3232 product page, the MAX3232 family is pin, package, and functionally compatible with the industry-standard MAX232. The selected MAX3232ECTE+T ordering code uses a 16-pin TQFN package with an exposed pad.
What are the key specifications of MAX3232ECTE+T that engineers should know?
The MAX3232ECTE+T provides a 3.0 V to 5.5 V operating supply, two transmitters, two receivers, a maximum data rate of 1 Mbps, 15 kV ESD protection, and shutdown current down to 10 nA. Analog Devices describes it as a low-power true-RS-232 transceiver. It is supplied in a 16-pin TQFN package with an exposed pad and a specified operating range of 0 °C to 70 °C.
Where can I download the MAX3232ECTE+T datasheet PDF?
The MAX3232ECTE+T datasheet and product information are available from the official Analog Devices MAX3232 product page at https://www.analog.com/en/products/max3232.html. The page identifies the data sheet as Revision 10 and provides the MAX3232 product information, selection table, documentation, and supporting tools. Use the manufacturer document for final electrical limits, capacitor values, pin functions, and package drawings.
Where can I find the MAX3232ECTE+T pinout?
The MAX3232ECTE+T pinout is published in the Analog Devices MAX3232 manufacturer data sheet rather than on a separate verified pin-assignment source. The device uses a 16-pin TQFN package with an exposed pad. Before assigning PCB tracks, use the pin-description table and land-pattern information in the manufacturer data sheet to confirm every driver, receiver, charge-pump, power, and exposed-pad connection.
Can MAX3232ECTE+T operate from 3.3 V?
Yes, the MAX3232ECTE+T can operate from a 3.3 V supply because its specified operating voltage range is 3.0 V to 5.5 V. This allows direct compatibility with common 3.3 V embedded-controller and FPGA I/O environments. The interface still generates the bipolar voltage levels required by true RS-232 through its internal charge-pump circuitry.
What is the maximum data rate of MAX3232ECTE+T?
The MAX3232ECTE+T supports data rates up to 1 Mbps, as stated on the Analog Devices MAX3232 product page and distributor product summaries. That rate is sufficient for many legacy serial-console, control, instrumentation, and point-of-sale links. Cable length, capacitance, grounding, and the connected system must still be considered when operating near the maximum signaling rate.
Where can I buy MAX3232ECTE+T online?
Use the Request a Quote form on this page to request MAX3232ECTE+T availability, current lead time, and a quotation for the required quantity. The Analog Devices product page lists the MAX3232 as being in production, while availability and commercial terms can change with order quantity. The request form is the appropriate channel for current sourcing and package-quantity confirmation.
What is the price of MAX3232ECTE+T?
Use the Request a Quote form on this page for the current MAX3232ECTE+T price and volume terms. Pricing depends on order quantity, shipment configuration, and current commercial availability. The manufacturer product page displays family-level list-price information, but this page does not treat a starting family price as a quantity-qualified quotation for the exact ordering code.
What is the lead time for MAX3232ECTE+T?
Request the current MAX3232ECTE+T lead time through the Request a Quote form on this page. Analog Devices identifies the MAX3232 family as being in production, but production status does not by itself establish a fixed lead time for every quantity or reel configuration. Include the required quantity, date code requirements, and destination in the request for an actionable supply response.
Is MAX3232ECTE+T in stock?
Request a stock and availability confirmation for MAX3232ECTE+T through the Request a Quote form on this page. The manufacturer lists the MAX3232 family as being in production, while live stock can vary by exact ordering code, quantity, and packaging format. Provide the required reel quantity and production schedule so the quotation can reflect the appropriate configuration.
What is the difference between MAX3232ECTE+T and MAX3232ECAE+T?
Both MAX3232ECTE+T and MAX3232ECAE+T belong to the same MAX3232E interface family and use the same 16-pin TQFN exposed-pad package. Their core interface parameters remain 2 transmitters, 2 receivers, a 3.0 V to 5.5 V supply range, and operation up to 1 Mbps. The ordering-code temperature-grade distinction should be checked against the Analog Devices ordering table before substitution.
When should I choose MAX3232ECTE+T over MAX3232EATE+T?
Choose MAX3232ECTE+T when its specified 0 °C to 70 °C operating range covers the product environment and you require the 16-pin TQFN exposed-pad footprint. Choose MAX3232EATE+T when the system needs its corresponding temperature grade and the manufacturer confirms that grade is suitable. Both families provide the same core 3.0 V to 5.5 V, dual-driver, dual-receiver, 1 Mbps RS-232 interface.
Is MAX3232ECTE+T suitable for industrial control systems?
The MAX3232ECTE+T is suitable when the enclosure temperature stays within its specified 0 °C to 70 °C range and the exposed-pad thermal design is adequate. Its 3.0 V to 5.5 V supply flexibility, 1 Mbps data rate, and 15 kV ESD protection suit short-distance legacy serial links in industrial controllers, adapters, and instrumentation. For wider temperature ranges, select and verify the appropriate MAX3232E temperature-grade variant.
What can replace MAX3232ECTE+T?
The closest verified replacements are same-family MAX3232E ordering variants that retain the 16-pin TQFN exposed-pad footprint and the core two-driver, two-receiver RS-232 configuration. MAX3232ECAE+T and MAX3232EATE+T can be evaluated as pin-compatible alternatives, provided their temperature grade and ordering information are checked. SOIC-package alternatives such as MAX3232ECDWR are not drop-in replacements because the land pattern differs.
What is the best drop-in replacement for MAX3232ECTE+T?
MAX3232ECAE+T is the most directly documented same-package option for evaluating as a drop-in replacement for MAX3232ECTE+T. Both use a 16-pin TQFN package and retain the 2/2 RS-232 configuration, 3.0 V to 5.5 V supply range, and 1 Mbps data rate. Final approval should also verify the temperature grade, exposed-pad land pattern, capacitor requirements, and lifecycle status in the manufacturer documentation.
What is the best Analog Devices equivalent for MAX3232ECTE+T?
The best same-manufacturer equivalents to evaluate are MAX3232ECAE+T and MAX3232EATE+T because they remain in the MAX3232E family and use the same TQFN exposed-pad package class. Their core electrical ratings—3.0 V to 5.5 V operation, 2 transmitters, 2 receivers, and up to 1 Mbps—align with the target. Check the ordering table and temperature requirements before releasing a substitution.

Справочные инженерные данные для MAX3232ECTE+T — сравнение, рекомендации по проектированию и информация о соответствии.

Руководство по выбору

Choose MAX3232ECTE+T when the design needs a compact 5 mm by 5 mm TQFN-16 true-RS-232 interface, a 3.0 V to 5.5 V supply range, two drivers, two receivers, and operation up to 1 Mbps. Choose MAX3232ECAE+T or MAX3232EATE+T when the manufacturer ordering table confirms that the corresponding temperature grade is better suited to the enclosure environment; their core interface ratings remain aligned. Avoid MAX3232ECDWR and other SOIC-package versions when the existing board uses the MAX3232ECTE+T land pattern because they require a PCB change. The MAX3232ECTE+T is also preferable to a 5 V-only interface in a 3.3 V system because its 3.0 V minimum supply supports direct operation from a 3.3 V rail. Before release, verify the selected variant's temperature range, exposed-pad layout, capacitor values, and connector-specific ESD and grounding implementation.

Сравнение с аналогами

Параметр Этот товар MAX3232ECAE+T MAX3232EATE+T
Brand Analog Devices Analog Devices Analog Devices
Package TQFN-16 with exposed pad, 5 mm x 5 mm TQFN-16 with exposed pad, 5 mm x 5 mm TQFN-16 with exposed pad, 5 mm x 5 mm
Transceiver Configuration 2 transmitters and 2 receivers 2 transmitters and 2 receivers 2 transmitters and 2 receivers
Supply Voltage Range 3.0 V to 5.5 V 3.0 V to 5.5 V 3.0 V to 5.5 V
Maximum Data Rate 1 Mbps 1 Mbps 1 Mbps
ESD Protection 15 kV 15 kV 15 kV
Interface Type True RS-232 True RS-232 True RS-232
Packing Method Tape and reel Tape and reel Tape and reel

Ключевые отличия

  • Compact exposed-pad interface implementation (против MAX3232ECDWR)
  • 3.3 V-compatible true RS-232 operation (против MAX3232ECWE+)
  • Full dual-channel RS-232 interface (против MAX3232EATE+T)

Заметки по проектированию

Place the MAX3232 charge-pump capacitors and bypass capacitor directly beside their numbered pins using the shortest possible traces. Follow the manufacturer data sheet for capacitance, tolerance, voltage rating, and placement. The exposed pad is both a thermal and electrical connection; solder it to a ground plane and use the recommended thermal-via pattern. Avoid placing the charge-pump routing near sensitive analog inputs because its switching waveform can couple into adjacent nodes.

Keep connector-side RS-232 traces away from clocks, switching-regulator outputs, and high-speed digital nets. Maintain a continuous ground reference beneath the interface path, but follow the connector and cable grounding strategy to control ground currents. If the MAX3232 is positioned away from the connector, route the protected driver and receiver nets together and minimize stubs to reduce susceptibility to external noise and ESD events.

Do not substitute a SOIC or SSOP MAX3232 variant onto the TQFN footprint without redesigning the PCB. MAX3232ECDWR, for example, uses a different package and therefore is not a pin-to-pin drop-in replacement for MAX3232ECTE+T. Also verify the operating-temperature grade before substitution: identical voltage, data-rate, and channel-count ratings do not establish suitability for an environment outside the target device's specified temperature range.

Информация о соответствии

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Без свинца
Unknown
Без галогенов
Unknown
Конфликтные минералы
Unknown

The MAX3232 family is specified with 15 kV ESD protection. A separate IEC ESD-protection designation is stated for the TI MAX3232E family, but it was not applied to the exact Analog Devices target ordering code. RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations were not established for the exact MPN.

Похожие запросы

MAX3232ECTE+T datasheet MAX3232ECTE+T pinout MAX3232ECTE+T datasheet pdf MAX3232ECTE+T equivalent MAX3232ECTE+T replacement MAX3232ECTE+T cross reference MAX3232ECTE+T price MAX3232ECTE+T stock Analog Devices MAX3232ECTE+T MAX3232ECTE+T TQFN-16 footprint MAX3232ECTE+T 1Mbps RS-232 MAX3232ECTE+T vs MAX3232ECDWR MAX3232ECTE+T application circuit MAX3232ECTE+T 3.3V operation

Связанные компоненты & термины

Analog Devices MAX3232ECTE+T MAX3232ECAE+T MAX3232EATE+T MAX3232ECDWR RS-232 transceiver true RS-232 interface IC line driver line receiver dual charge pump TIA/EIA-232 ESD protection 15 kV ESD TQFN-16 exposed pad surface-mount package 3.3 V logic interface 1 Mbps data rate industrial serial communication USB-to-RS-232 adapter data-acquisition equipment point-of-sale terminal Analog Devices MAX3232 MAX232
Быстрый запрос цены (RFQ)
Заполните все данные — наша команда продаж ответит в течение 24 часов
Артикул Производитель Корпус QTY Целевая цена Итого
✓
Запрос цены отправлен!

Мы ответим на ваш email в течение 24 часов

1
RFQ отправлен
2
Предложение получено
3
Заказ оформлен
4
Оплата
5
Отправлено
6
Доставлено
Просмотреть детали RFQ