MAX3243ECDWR - 500kbps 3-5.5V RS-232 Transceiver | Texas Instruments
Артикул: MAX3243ECDWR ✓ АктивенMAX3243ECDWR Обзор
An RS-232 transceiver is an interface IC that converts logic-level signals into RS-232-compatible levels and converts incoming RS-232 signals back into logic levels. It belongs to the interface IC category and provides the physical signaling layer between an asynchronous communication controller and a serial-port connection. The MAX3243E is designed for equipment that needs multiple RS-232 channels without requiring a separate external voltage-conversion circuit.
The MAX3243ECDWR operates from a 3 V to 5.5 V supply, allowing it to work with both 3.3 V and 5 V system rails. Its internal dual charge-pump circuit supports the positive and negative voltage levels required by RS-232. According to the manufacturer datasheet, the serial-port connection pins provide ±15 kV ESD protection under HBM and IEC 61000-4-2 air-gap discharge conditions, plus ±8 kV under IEC 61000-4-2 contact discharge conditions.
The integrated charge-pump design reduces the external component count compared with an RS-232 implementation that relies on a separate external supply. Three driver channels can transmit logic signals, while five receiver channels can independently receive serial data. The device supports communication rates up to 500 kbps and meets the electrical requirements stated in the manufacturer documentation for TIA/EIA-232-F operation.
Typical uses include industrial serial-port equipment, data-collection systems, point-of-sale terminals, laboratory instrumentation, and embedded control systems. A five-receiver arrangement is useful when a system monitors several RS-232 sources, while the three-driver arrangement supports multiple outbound serial links. The 28-pin SOIC package also simplifies assembly for designs requiring a conventional surface-mount footprint.
Layout should keep charge-pump and interface routing away from sensitive analog or high-speed digital paths. Follow the manufacturer datasheet for recommended capacitor placement, serial-interface routing, and power-supply decoupling. Confirm the system ground arrangement and RS-232 connector protection requirements before finalizing a production board.
This product page organizes the key electrical ratings, package details, RS-232 interface functions, ESD levels, and application guidance for the MAX3243ECDWR. It also identifies where additional design information, such as exact package dimensions and complete pin descriptions, should be taken directly from the manufacturer documentation.
Аналоги без доработки для MAX3243ECDWR — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Для этого товара нет аналогов без доработки.
Запросить аналогиMAX3243ECDWR Характеристики
| Product Type | Multichannel RS-232 line driver/receiver |
| Supply Voltage Range | 3 V to 5.5 V |
| Maximum Data Rate | 500 kbps |
| Number of Line Drivers | 3 |
| Number of Line Receivers | 5 |
| Charge-Pump Configuration | Dual charge-pump circuit |
| HBM and IEC Air-Gap ESD Protection | ±15 kV |
| IEC 61000-4-2 Contact Discharge Protection | ±8 kV |
| Диапазон рабочих температур | 0°C to 70°C |
| Корпус | 28-pin SOIC (DW) |
| Package Width | 7.50 mm (0.295 inch) |
| Тип монтажа | Surface mount |
| Total Pin Count | 28 pins |
| RS-232 Compliance | TIA/EIA-232-F |
| Interface Standard | RS-232 |
Руководство по цоколевке MAX3243ECDWR в корпусе 7.50 mm (0.295 inch)
Цоколевка для MAX3243ECDWR (корпус 7.50 mm (0.295 inch)). Нумерация выводов, функции и схемы подключения определены в техническом описании производителя. Обратитесь к нему для точного посадочного места и рекомендаций по пайке.
Нет подробных данных о распиновке для MAX3243ECDWR.
Обратитесь к даташиту для полной конфигурации выводов.
Типичное применение
MAX3243ECDWR подходит для 6 применениеs: Industrial Serial-Port Control, Point-of-Sale Terminal, Data-Acquisition System, Laboratory Instrument Communication, Embedded Service Console, Network Equipment Management.
Industrial Serial-Port Control
The MAX3243ECDWR fits industrial controllers that need several RS-232 links for sensors, scales, service tools, or remote equipment. Its three drivers and five receivers provide more channels than a single-channel transceiver while the integrated dual charge-pump circuit reduces the number of supporting power components. Operation from 3 V to 5.5 V permits use with 3.3 V controllers, and the 500 kbps capability supports high-speed legacy serial traffic. Place the device according to the manufacturer application circuit, keep charge-pump routing away from sensitive signals, and provide suitable enclosure-level surge protection for cables leaving the controlled area.
Рекомендуется
Point-of-Sale Terminal
The MAX3243ECDWR is suitable for a point-of-sale terminal that connects receipt printers, card readers, scanners, and local diagnostic equipment through RS-232. Three transmit channels and five receive channels support a multi-peripheral arrangement without requiring one complete transceiver package per port. Its 3 V to 5.5 V supply range accommodates common embedded logic rails, while the 500 kbps rating accommodates common serial peripheral rates. The integrated dual charge-pump arrangement simplifies the power section, but the design must still follow the manufacturer capacitor-placement guidance and keep external cable transients away from the logic domain.
Рекомендуется
Data-Acquisition System
The MAX3243ECDWR can serve as the host-side RS-232 interface in a laboratory or plant-floor data-acquisition system. Its five receiver channels allow several instruments or transducers to be monitored, while three drivers support commands or configuration outputs to selected devices. The 28-pin SOIC package provides a conventional surface-mount assembly option, and the 3 V to 5.5 V operating range supports both legacy 5 V and modern 3.3 V control platforms. For reliable acquisition, isolate noisy grounds where required, route cable-side signals directly to the interface pins, and apply the manufacturer's recommended supply and charge-pump layout.
Рекомендуется
Laboratory Instrument Communication
The MAX3243ECDWR is appropriate for laboratory instruments that expose RS-232 connections to computers, service fixtures, or calibration equipment. Three driver channels support outbound commands and status links, while five receiver channels can accept responses from multiple instruments. With a maximum data rate of 500 kbps, the interface provides ample margin for many asynchronous serial-control protocols. The integrated charge-pump circuitry simplifies the analog interface section, although instrument designers should preserve recommended capacitor spacing, provide solid grounding, and prevent externally connected cables from introducing transients beyond the device's specified ESD ratings.
Рекомендуется
Embedded Service Console
The MAX3243ECDWR fits an embedded service console requiring several legacy communication ports for configuration, diagnostics, and firmware update interfaces. Its three-driver and five-receiver arrangement can consolidate multiple RS-232 links into one 28-pin SOIC package, reducing board area compared with separate single-channel devices. The 3 V to 5.5 V supply range allows deployment in either 5 V or 3.3 V embedded platforms, and the 500 kbps rate supports common asynchronous command protocols. Use the manufacturer application schematic to establish charge-pump component placement and verify signal levels, grounding, and connector protection before releasing the layout.
Рекомендуется
Network Equipment Management
The MAX3243ECDWR can provide legacy RS-232 management ports on switches, routers, gateways, and related communication equipment during installation or field maintenance. Multiple drivers and receivers allow a unit to connect to several configuration consoles or diagnostic adapters, while the integrated charge-pump circuit keeps the external support network compact. The 500 kbps capability is suitable for asynchronous management links, and operation across 3 V to 5.5 V gives board designers flexibility in system rail selection. Because RS-232 ports may be connected to long or exposed cables, the enclosure and connector should add appropriate transient protection beyond the chip's specified connector-pin ESD capability.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для MAX3243ECDWR — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар |
|---|---|
| Brand | Texas Instruments |
| Package | 28-pin SOIC (DW) |
| Product Type | Multichannel RS-232 line driver/receiver |
| Supply Voltage Range | 3 V to 5.5 V |
| Maximum Data Rate | 500 kbps |
| Line Drivers | 3 |
| Line Receivers | 5 |
| HBM and IEC Air-Gap ESD Protection | ±15 kV |
| IEC 61000-4-2 Contact Discharge Protection | ±8 kV |
| Operating Temperature Range | 0°C to 70°C |
| RS-232 Compliance | TIA/EIA-232-F |
| Charge-Pump Circuit | Dual charge-pump circuit |
Ключевые отличия
- Broader integrated channel count (против MAX3232ECDR)
- Single-package multi-port consolidation (против MAX232EIDR)
- Higher specified data-rate capability (против MAX3232ECDR)
- Documented connector-pin ESD protection (против MAX3232CDBR)
Заметки по проектированию
Place the charge-pump capacitors at the locations shown in the Texas Instruments MAX3243 datasheet application circuit and keep these connections short. Route the charge-pump and RS-232 driver outputs away from sensitive receiver inputs and unrelated high-speed logic. This separation helps prevent coupling from switching charge-pump nodes into measurement or communication channels.
Connect the device to a low-impedance supply plane and place the manufacturer's recommended decoupling capacitor close to the supply pins. The MAX3243ECDWR operates from 3 V to 5.5 V, but correct local decoupling remains important because the dual charge-pump circuit draws periodic current from the supply. Validate the layout with the expected cable load and external transient conditions.
Do not treat the specified connector-pin ESD rating as a complete industrial surge-protection solution. The device provides ±15 kV HBM and IEC 61000-4-2 air-gap protection and ±8 kV contact-discharge protection, but long cables may expose the port to larger system-level transients. Add appropriate connector, cable, and enclosure protection when the equipment operates outside a controlled environment.
Follow the manufacturer pin-description table when assigning the 28-pin SOIC footprint, especially the driver outputs, receiver inputs, supply pins, and ground connections. Do not infer unused or reserved connections from the three-driver and five-receiver configuration. Keep logic-side and cable-side return paths controlled so ground currents produced by external equipment do not disturb the host controller.
Информация о соответствии
The manufacturer documentation identifies IEC 61000-4-2 and TIA/EIA-232-F requirements. RoHS, REACH, lead-free, halogen-free, conflict-minerals, and automotive-qualification status require separate manufacturer confirmation.