MAX3243ECDWR - 500kbps 3-5.5V RS-232 Transceiver | Texas Instruments
料号: MAX3243ECDWR ✓ 量产中MAX3243ECDWR 概述
An RS-232 transceiver is an interface IC that converts logic-level signals into RS-232-compatible levels and converts incoming RS-232 signals back into logic levels. It belongs to the interface IC category and provides the physical signaling layer between an asynchronous communication controller and a serial-port connection. The MAX3243E is designed for equipment that needs multiple RS-232 channels without requiring a separate external voltage-conversion circuit.
The MAX3243ECDWR operates from a 3 V to 5.5 V supply, allowing it to work with both 3.3 V and 5 V system rails. Its internal dual charge-pump circuit supports the positive and negative voltage levels required by RS-232. According to the manufacturer datasheet, the serial-port connection pins provide ±15 kV ESD protection under HBM and IEC 61000-4-2 air-gap discharge conditions, plus ±8 kV under IEC 61000-4-2 contact discharge conditions.
The integrated charge-pump design reduces the external component count compared with an RS-232 implementation that relies on a separate external supply. Three driver channels can transmit logic signals, while five receiver channels can independently receive serial data. The device supports communication rates up to 500 kbps and meets the electrical requirements stated in the manufacturer documentation for TIA/EIA-232-F operation.
Typical uses include industrial serial-port equipment, data-collection systems, point-of-sale terminals, laboratory instrumentation, and embedded control systems. A five-receiver arrangement is useful when a system monitors several RS-232 sources, while the three-driver arrangement supports multiple outbound serial links. The 28-pin SOIC package also simplifies assembly for designs requiring a conventional surface-mount footprint.
Layout should keep charge-pump and interface routing away from sensitive analog or high-speed digital paths. Follow the manufacturer datasheet for recommended capacitor placement, serial-interface routing, and power-supply decoupling. Confirm the system ground arrangement and RS-232 connector protection requirements before finalizing a production board.
This product page organizes the key electrical ratings, package details, RS-232 interface functions, ESD levels, and application guidance for the MAX3243ECDWR. It also identifies where additional design information, such as exact package dimensions and complete pin descriptions, should be taken directly from the manufacturer documentation.
直接替换替代料: MAX3243ECDWR ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
该产品暂无直接替换替代料。
请求替代料MAX3243ECDWR 规格参数
| Product Type | Multichannel RS-232 line driver/receiver |
| Supply Voltage Range | 3 V to 5.5 V |
| Maximum Data Rate | 500 kbps |
| Number of Line Drivers | 3 |
| Number of Line Receivers | 5 |
| Charge-Pump Configuration | Dual charge-pump circuit |
| HBM and IEC Air-Gap ESD Protection | ±15 kV |
| IEC 61000-4-2 Contact Discharge Protection | ±8 kV |
| 工作温度范围 | 0°C to 70°C |
| 封装 | 28-pin SOIC (DW) |
| Package Width | 7.50 mm (0.295 inch) |
| 安装类型 | Surface mount |
| Total Pin Count | 28 pins |
| RS-232 Compliance | TIA/EIA-232-F |
| Interface Standard | RS-232 |
MAX3243ECDWR 7.50 mm (0.295 inch) 引脚配置指南
MAX3243ECDWR(7.50 mm (0.295 inch) 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。
暂无详细引脚数据: MAX3243ECDWR.
请参阅 数据手册 以查看完整引脚配置。
典型应用
MAX3243ECDWR 适用于 6 应用s: Industrial Serial-Port Control, Point-of-Sale Terminal, Data-Acquisition System, Laboratory Instrument Communication, Embedded Service Console, Network Equipment Management.
Industrial Serial-Port Control
The MAX3243ECDWR fits industrial controllers that need several RS-232 links for sensors, scales, service tools, or remote equipment. Its three drivers and five receivers provide more channels than a single-channel transceiver while the integrated dual charge-pump circuit reduces the number of supporting power components. Operation from 3 V to 5.5 V permits use with 3.3 V controllers, and the 500 kbps capability supports high-speed legacy serial traffic. Place the device according to the manufacturer application circuit, keep charge-pump routing away from sensitive signals, and provide suitable enclosure-level surge protection for cables leaving the controlled area.
推荐
Point-of-Sale Terminal
The MAX3243ECDWR is suitable for a point-of-sale terminal that connects receipt printers, card readers, scanners, and local diagnostic equipment through RS-232. Three transmit channels and five receive channels support a multi-peripheral arrangement without requiring one complete transceiver package per port. Its 3 V to 5.5 V supply range accommodates common embedded logic rails, while the 500 kbps rating accommodates common serial peripheral rates. The integrated dual charge-pump arrangement simplifies the power section, but the design must still follow the manufacturer capacitor-placement guidance and keep external cable transients away from the logic domain.
推荐
Data-Acquisition System
The MAX3243ECDWR can serve as the host-side RS-232 interface in a laboratory or plant-floor data-acquisition system. Its five receiver channels allow several instruments or transducers to be monitored, while three drivers support commands or configuration outputs to selected devices. The 28-pin SOIC package provides a conventional surface-mount assembly option, and the 3 V to 5.5 V operating range supports both legacy 5 V and modern 3.3 V control platforms. For reliable acquisition, isolate noisy grounds where required, route cable-side signals directly to the interface pins, and apply the manufacturer's recommended supply and charge-pump layout.
推荐
Laboratory Instrument Communication
The MAX3243ECDWR is appropriate for laboratory instruments that expose RS-232 connections to computers, service fixtures, or calibration equipment. Three driver channels support outbound commands and status links, while five receiver channels can accept responses from multiple instruments. With a maximum data rate of 500 kbps, the interface provides ample margin for many asynchronous serial-control protocols. The integrated charge-pump circuitry simplifies the analog interface section, although instrument designers should preserve recommended capacitor spacing, provide solid grounding, and prevent externally connected cables from introducing transients beyond the device's specified ESD ratings.
推荐
Embedded Service Console
The MAX3243ECDWR fits an embedded service console requiring several legacy communication ports for configuration, diagnostics, and firmware update interfaces. Its three-driver and five-receiver arrangement can consolidate multiple RS-232 links into one 28-pin SOIC package, reducing board area compared with separate single-channel devices. The 3 V to 5.5 V supply range allows deployment in either 5 V or 3.3 V embedded platforms, and the 500 kbps rate supports common asynchronous command protocols. Use the manufacturer application schematic to establish charge-pump component placement and verify signal levels, grounding, and connector protection before releasing the layout.
推荐
Network Equipment Management
The MAX3243ECDWR can provide legacy RS-232 management ports on switches, routers, gateways, and related communication equipment during installation or field maintenance. Multiple drivers and receivers allow a unit to connect to several configuration consoles or diagnostic adapters, while the integrated charge-pump circuit keeps the external support network compact. The 500 kbps capability is suitable for asynchronous management links, and operation across 3 V to 5.5 V gives board designers flexibility in system rail selection. Because RS-232 ports may be connected to long or exposed cables, the enclosure and connector should add appropriate transient protection beyond the chip's specified connector-pin ESD capability.
推荐
推荐产品汇总
工程参考数据: MAX3243ECDWR ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 |
|---|---|
| Brand | Texas Instruments |
| Package | 28-pin SOIC (DW) |
| Product Type | Multichannel RS-232 line driver/receiver |
| Supply Voltage Range | 3 V to 5.5 V |
| Maximum Data Rate | 500 kbps |
| Line Drivers | 3 |
| Line Receivers | 5 |
| HBM and IEC Air-Gap ESD Protection | ±15 kV |
| IEC 61000-4-2 Contact Discharge Protection | ±8 kV |
| Operating Temperature Range | 0°C to 70°C |
| RS-232 Compliance | TIA/EIA-232-F |
| Charge-Pump Circuit | Dual charge-pump circuit |
关键差异点
- Broader integrated channel count (对比 MAX3232ECDR)
- Single-package multi-port consolidation (对比 MAX232EIDR)
- Higher specified data-rate capability (对比 MAX3232ECDR)
- Documented connector-pin ESD protection (对比 MAX3232CDBR)
设计说明
Place the charge-pump capacitors at the locations shown in the Texas Instruments MAX3243 datasheet application circuit and keep these connections short. Route the charge-pump and RS-232 driver outputs away from sensitive receiver inputs and unrelated high-speed logic. This separation helps prevent coupling from switching charge-pump nodes into measurement or communication channels.
Connect the device to a low-impedance supply plane and place the manufacturer's recommended decoupling capacitor close to the supply pins. The MAX3243ECDWR operates from 3 V to 5.5 V, but correct local decoupling remains important because the dual charge-pump circuit draws periodic current from the supply. Validate the layout with the expected cable load and external transient conditions.
Do not treat the specified connector-pin ESD rating as a complete industrial surge-protection solution. The device provides ±15 kV HBM and IEC 61000-4-2 air-gap protection and ±8 kV contact-discharge protection, but long cables may expose the port to larger system-level transients. Add appropriate connector, cable, and enclosure protection when the equipment operates outside a controlled environment.
Follow the manufacturer pin-description table when assigning the 28-pin SOIC footprint, especially the driver outputs, receiver inputs, supply pins, and ground connections. Do not infer unused or reserved connections from the three-driver and five-receiver configuration. Keep logic-side and cable-side return paths controlled so ground currents produced by external equipment do not disturb the host controller.
合规信息
The manufacturer documentation identifies IEC 61000-4-2 and TIA/EIA-232-F requirements. RoHS, REACH, lead-free, halogen-free, conflict-minerals, and automotive-qualification status require separate manufacturer confirmation.