MAX3243ECDWR - 500kbps 3-5.5V RS-232 Transceiver | Texas Instruments
MPN: MAX3243ECDWR ✓ Hoạt độngMAX3243ECDWR Tóm tắt
An RS-232 transceiver is an interface IC that converts logic-level signals into RS-232-compatible levels and converts incoming RS-232 signals back into logic levels. It belongs to the interface IC category and provides the physical signaling layer between an asynchronous communication controller and a serial-port connection. The MAX3243E is designed for equipment that needs multiple RS-232 channels without requiring a separate external voltage-conversion circuit.
The MAX3243ECDWR operates from a 3 V to 5.5 V supply, allowing it to work with both 3.3 V and 5 V system rails. Its internal dual charge-pump circuit supports the positive and negative voltage levels required by RS-232. According to the manufacturer datasheet, the serial-port connection pins provide ±15 kV ESD protection under HBM and IEC 61000-4-2 air-gap discharge conditions, plus ±8 kV under IEC 61000-4-2 contact discharge conditions.
The integrated charge-pump design reduces the external component count compared with an RS-232 implementation that relies on a separate external supply. Three driver channels can transmit logic signals, while five receiver channels can independently receive serial data. The device supports communication rates up to 500 kbps and meets the electrical requirements stated in the manufacturer documentation for TIA/EIA-232-F operation.
Typical uses include industrial serial-port equipment, data-collection systems, point-of-sale terminals, laboratory instrumentation, and embedded control systems. A five-receiver arrangement is useful when a system monitors several RS-232 sources, while the three-driver arrangement supports multiple outbound serial links. The 28-pin SOIC package also simplifies assembly for designs requiring a conventional surface-mount footprint.
Layout should keep charge-pump and interface routing away from sensitive analog or high-speed digital paths. Follow the manufacturer datasheet for recommended capacitor placement, serial-interface routing, and power-supply decoupling. Confirm the system ground arrangement and RS-232 connector protection requirements before finalizing a production board.
This product page organizes the key electrical ratings, package details, RS-232 interface functions, ESD levels, and application guidance for the MAX3243ECDWR. It also identifies where additional design information, such as exact package dimensions and complete pin descriptions, should be taken directly from the manufacturer documentation.
Bộ thay thế dễ dàng lắp đặt cho MAX3243ECDWR — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Không có bộ thay thế dễ dàng lắp đặt sẵn có cho sản phẩm này.
Yêu cầu các bộ thay thếMAX3243ECDWR Thông số kỹ thuật
| Product Type | Multichannel RS-232 line driver/receiver |
| Supply Voltage Range | 3 V to 5.5 V |
| Maximum Data Rate | 500 kbps |
| Number of Line Drivers | 3 |
| Number of Line Receivers | 5 |
| Charge-Pump Configuration | Dual charge-pump circuit |
| HBM and IEC Air-Gap ESD Protection | ±15 kV |
| IEC 61000-4-2 Contact Discharge Protection | ±8 kV |
| Khoảng nhiệt độ hoạt động | 0°C to 70°C |
| Hộp | 28-pin SOIC (DW) |
| Package Width | 7.50 mm (0.295 inch) |
| Kiểu lắp đặt | Surface mount |
| Total Pin Count | 28 pins |
| RS-232 Compliance | TIA/EIA-232-F |
| Interface Standard | RS-232 |
Hướng dẫn cấu hình chân MAX3243ECDWR 7.50 mm (0.295 inch)
Cấu hình chân cho MAX3243ECDWR (7.50 mm (0.295 inch) gói). Số thứ tự chân, chức năng và sơ đồ kết nối được xác định trong tài liệu thông số kỹ thuật của nhà sản xuất. Tham khảo nó để biết footprint và hướng dẫn hàn chính xác.
Không có dữ liệu chân cụ thể sẵn có cho MAX3243ECDWR.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
MAX3243ECDWR phù hợp cho 6 Áp dụngs: Industrial Serial-Port Control, Point-of-Sale Terminal, Data-Acquisition System, Laboratory Instrument Communication, Embedded Service Console, Network Equipment Management.
Industrial Serial-Port Control
The MAX3243ECDWR fits industrial controllers that need several RS-232 links for sensors, scales, service tools, or remote equipment. Its three drivers and five receivers provide more channels than a single-channel transceiver while the integrated dual charge-pump circuit reduces the number of supporting power components. Operation from 3 V to 5.5 V permits use with 3.3 V controllers, and the 500 kbps capability supports high-speed legacy serial traffic. Place the device according to the manufacturer application circuit, keep charge-pump routing away from sensitive signals, and provide suitable enclosure-level surge protection for cables leaving the controlled area.
Được đề xuất
Point-of-Sale Terminal
The MAX3243ECDWR is suitable for a point-of-sale terminal that connects receipt printers, card readers, scanners, and local diagnostic equipment through RS-232. Three transmit channels and five receive channels support a multi-peripheral arrangement without requiring one complete transceiver package per port. Its 3 V to 5.5 V supply range accommodates common embedded logic rails, while the 500 kbps rating accommodates common serial peripheral rates. The integrated dual charge-pump arrangement simplifies the power section, but the design must still follow the manufacturer capacitor-placement guidance and keep external cable transients away from the logic domain.
Được đề xuất
Data-Acquisition System
The MAX3243ECDWR can serve as the host-side RS-232 interface in a laboratory or plant-floor data-acquisition system. Its five receiver channels allow several instruments or transducers to be monitored, while three drivers support commands or configuration outputs to selected devices. The 28-pin SOIC package provides a conventional surface-mount assembly option, and the 3 V to 5.5 V operating range supports both legacy 5 V and modern 3.3 V control platforms. For reliable acquisition, isolate noisy grounds where required, route cable-side signals directly to the interface pins, and apply the manufacturer's recommended supply and charge-pump layout.
Được đề xuất
Laboratory Instrument Communication
The MAX3243ECDWR is appropriate for laboratory instruments that expose RS-232 connections to computers, service fixtures, or calibration equipment. Three driver channels support outbound commands and status links, while five receiver channels can accept responses from multiple instruments. With a maximum data rate of 500 kbps, the interface provides ample margin for many asynchronous serial-control protocols. The integrated charge-pump circuitry simplifies the analog interface section, although instrument designers should preserve recommended capacitor spacing, provide solid grounding, and prevent externally connected cables from introducing transients beyond the device's specified ESD ratings.
Được đề xuất
Embedded Service Console
The MAX3243ECDWR fits an embedded service console requiring several legacy communication ports for configuration, diagnostics, and firmware update interfaces. Its three-driver and five-receiver arrangement can consolidate multiple RS-232 links into one 28-pin SOIC package, reducing board area compared with separate single-channel devices. The 3 V to 5.5 V supply range allows deployment in either 5 V or 3.3 V embedded platforms, and the 500 kbps rate supports common asynchronous command protocols. Use the manufacturer application schematic to establish charge-pump component placement and verify signal levels, grounding, and connector protection before releasing the layout.
Được đề xuất
Network Equipment Management
The MAX3243ECDWR can provide legacy RS-232 management ports on switches, routers, gateways, and related communication equipment during installation or field maintenance. Multiple drivers and receivers allow a unit to connect to several configuration consoles or diagnostic adapters, while the integrated charge-pump circuit keeps the external support network compact. The 500 kbps capability is suitable for asynchronous management links, and operation across 3 V to 5.5 V gives board designers flexibility in system rail selection. Because RS-232 ports may be connected to long or exposed cables, the enclosure and connector should add appropriate transient protection beyond the chip's specified connector-pin ESD capability.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho MAX3243ECDWR — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này |
|---|---|
| Brand | Texas Instruments |
| Package | 28-pin SOIC (DW) |
| Product Type | Multichannel RS-232 line driver/receiver |
| Supply Voltage Range | 3 V to 5.5 V |
| Maximum Data Rate | 500 kbps |
| Line Drivers | 3 |
| Line Receivers | 5 |
| HBM and IEC Air-Gap ESD Protection | ±15 kV |
| IEC 61000-4-2 Contact Discharge Protection | ±8 kV |
| Operating Temperature Range | 0°C to 70°C |
| RS-232 Compliance | TIA/EIA-232-F |
| Charge-Pump Circuit | Dual charge-pump circuit |
Bảo phân biệt quan trọng
- Broader integrated channel count (vsMAX3232ECDR)
- Single-package multi-port consolidation (vsMAX232EIDR)
- Higher specified data-rate capability (vsMAX3232ECDR)
- Documented connector-pin ESD protection (vsMAX3232CDBR)
Ghi chú thiết kế
Place the charge-pump capacitors at the locations shown in the Texas Instruments MAX3243 datasheet application circuit and keep these connections short. Route the charge-pump and RS-232 driver outputs away from sensitive receiver inputs and unrelated high-speed logic. This separation helps prevent coupling from switching charge-pump nodes into measurement or communication channels.
Connect the device to a low-impedance supply plane and place the manufacturer's recommended decoupling capacitor close to the supply pins. The MAX3243ECDWR operates from 3 V to 5.5 V, but correct local decoupling remains important because the dual charge-pump circuit draws periodic current from the supply. Validate the layout with the expected cable load and external transient conditions.
Do not treat the specified connector-pin ESD rating as a complete industrial surge-protection solution. The device provides ±15 kV HBM and IEC 61000-4-2 air-gap protection and ±8 kV contact-discharge protection, but long cables may expose the port to larger system-level transients. Add appropriate connector, cable, and enclosure protection when the equipment operates outside a controlled environment.
Follow the manufacturer pin-description table when assigning the 28-pin SOIC footprint, especially the driver outputs, receiver inputs, supply pins, and ground connections. Do not infer unused or reserved connections from the three-driver and five-receiver configuration. Keep logic-side and cable-side return paths controlled so ground currents produced by external equipment do not disturb the host controller.
Thông tin tuân thủ
The manufacturer documentation identifies IEC 61000-4-2 and TIA/EIA-232-F requirements. RoHS, REACH, lead-free, halogen-free, conflict-minerals, and automotive-qualification status require separate manufacturer confirmation.