MC9S08DZ60ACLH - S08 8-bit MCU 60KB Flash CAN LQFP-64 | NXP
Артикул: MC9S08DZ60ACLH ✗ Снят с производства| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $8.42 | $8,42 |
| 10 | $7.55 | $75,50 |
| 100 | $6.71 | $671,00 |
| 500 | $5.88 | $2.940,00 |
| 1.000 | $5.1 | $5.100,00 |
MC9S08DZ60ACLH Обзор
Background: The HCS08 is an 8-bit CISC microcontroller core from NXP (formerly Freescale) that succeeds the HC08 architecture with backward instruction-set compatibility. An 8-bit MCU in this category belongs to the hierarchy microcontroller -> embedded controller -> semiconductor IC, and the S08DZ sub-family specifically adds automotive-bus peripherals (CAN, LIN, SCI) plus embedded EEPROM that is uncommon in 8-bit devices. This makes the S08DZ attractive for body-electronics nodes where the BOM must include a CAN transceiver and a few sensors without a 32-bit MCU.
Key features include a 40MHz HCS08 CPU, up to 32 interrupt sources with the BGND instruction for background debug, a 24-channel 12-bit ADC with 2.5us conversion time, an embedded CAN 2.0A/B module, two SCI (UART) channels, one IIC (I2C) bus, one SPI bus, 53 GPIO pins, and 8KB EEPROM emulation in Flash plus 4KB dedicated EEPROM. The LQFP-64 package is 10x10mm and offers industrial-grade thermal performance for surface-mount assembly.
The device uses a 3.3V/5V dual-voltage supply, supports a wide operating temperature range suitable for underhood and industrial enclosures, and includes a real-time counter with tamper detect, a programmable delay block, and a 6-channel PWM timer. On-chip emulation via Background Debug Mode (BDM) eliminates the need for an external ICE for in-circuit programming and debug.
Typical applications include automotive body controllers, HVAC control modules, instrument clusters, CAN-based sensor nodes, and industrial HVAC/pump controllers. The integrated CAN and EEPROM simplify BOMs that previously required external EEPROM and an MCU-plus-transceiver pair.
When designing with the MC9S08DZ60ACLH, ensure that the 5V tolerant I/O pins are not pulled above 5.5V on a 3.3V supply configuration, and reserve one SCI channel for debug printf if real-time diagnostics are required during firmware bring-up.
This page synthesizes distributor pricing, same-package drop-in alternatives (MC9S08DZ60ACLF, S9S08DZ60F2MLHR, S9S08DZ96F2VLF), and practical design notes not found in the manufacturer datasheet alone.
Аналоги без доработки для MC9S08DZ60ACLH — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с MC9S08DZ60ACLH (тот же форм-фактор и посадочное место) — отличается по Package, Operating Temperature, Supply Voltage, ADC, Core.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
MC9S08DZ60ACLF
✅ Прямая замена✓ В наличии
$6.85 / шт.
Открыть даташит →MC9S08DZ60ACLC
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
S9S08DZ60F2MLHR
✅ Прямая замена ⚠️ Характеристики не проверены✓ В наличии
$4.08 / шт.
Открыть даташит →MC9S08DZ60AMLH
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
S9S08DZ96F2VLF
✅ Прямая замена ⚠️ Характеристики не проверены✓ В наличии
$6.55 / шт.
Открыть даташит →S9S08DZ32F2VLCR
✅ Прямая замена ⚠️ Характеристики не проверены✓ В наличии
$4.2 / шт.
Открыть даташит →MC9S08DZ60ACLH Максимальные параметры и электрические характеристики
| Core | HCS08 (8-bit CISC) |
| CPU Frequency | 40 MHz CPU / 20 MHz bus |
| Flash Size | 60 KB (60K x 8) |
| RAM Size | 2 KB |
| EEPROM Size | 4 KB |
| Разрядность шины данных | 8 bit |
| Корпус | 64-LQFP (10x10 mm) |
| Число выводов | 64 |
| Напряжение питания | 2.7 V to 5.5 V (3.3 V / 5 V dual) |
| ADC | 24-channel, 12-bit, 2.5 us conversion |
| CAN | 1 x CAN 2.0A/B |
| SCI (UART) | 2 channels |
| I2C | 1 channel |
| SPI | 1 channel |
| GPIO | 53 I/O pins |
| PWM | 6-channel timer/PWM |
| Рабочая температура | -40 C to +85 C (industrial) |
| Debug Interface | Background Debug Mode (BDM) |
| Тип монтажа | Surface Mount |
| Статус RoHS | Compliant |
Конфигурация выводов MC9S08DZ60ACLH
| Контакт 1 | BKGD/MS — Background Debug Mode / Mode Select |
| Контакт 2 | PTC5 — Port C GPIO 5 |
| Контакт 3 | PTC4 — Port C GPIO 4 |
| Контакт 4 | PTC3 — Port C GPIO 3 |
| Контакт 5 | PTC2 — Port C GPIO 2 |
| Контакт 6 | PTC1 — Port C GPIO 1 |
| Контакт 7 | PTC0 — Port C GPIO 0 |
| Контакт 8 | RESET — External reset input, active low |
| Контакт 9 | PTD7/TPM2CH5 — Port D GPIO 7 / TPM2 channel 5 |
| Контакт 10 | PTD6/TPM2CH4 — Port D GPIO 6 / TPM2 channel 4 |
| Контакт 11 | PTD5/TPM2CH3 — Port D GPIO 5 / TPM2 channel 3 |
| Контакт 12 | PTD4/TPM2CH2 — Port D GPIO 4 / TPM2 channel 2 |
| Контакт 13 | PTD3/TPM2CH1 — Port D GPIO 3 / TPM2 channel 1 |
| Контакт 14 | PTD2/TPM2CH0 — Port D GPIO 2 / TPM2 channel 0 |
| Контакт 15 | PTD1/ADP5 — Port D GPIO 1 / ADC channel 5 |
| Контакт 16 | VDD — Digital supply voltage |
| Контакт 17 | VSS — Digital ground |
| Контакт 18 | PTD0/ADP4 — Port D GPIO 0 / ADC channel 4 |
| Контакт 19 | PTE7/SPSCK — Port E GPIO 7 / SPI clock |
| Контакт 20 | PTE6/MOSI — Port E GPIO 6 / SPI MOSI |
| Контакт 21 | PTE5/MISO — Port E GPIO 5 / SPI MISO |
| Контакт 22 | PTE4/SS — Port E GPIO 4 / SPI slave select |
| Контакт 23 | PTE3/SDA — Port E GPIO 3 / I2C SDA |
| Контакт 24 | PTE2/SCL — Port E GPIO 2 / I2C SCL |
| Контакт 25 | PTE1/TXD2 — Port E GPIO 1 / SCI2 TXD |
| Контакт 26 | PTE0/RXD2 — Port E GPIO 0 / SCI2 RXD |
| Контакт 27 | PTB7/ADP7 — Port B GPIO 7 / ADC channel 7 |
| Контакт 28 | PTB6/ADP6 — Port B GPIO 6 / ADC channel 6 |
| Контакт 29 | PTB5/ADP9 — Port B GPIO 5 / ADC channel 9 / temperature sensor |
| Контакт 30 | PTB4/ADP8 — Port B GPIO 4 / ADC channel 8 |
| Контакт 31 | PTB3/ADP11 — Port B GPIO 3 / ADC channel 11 |
| Контакт 32 | PTB2/ADP10 — Port B GPIO 2 / ADC channel 10 |
| Контакт 33 | PTB1/ADP13 — Port B GPIO 1 / ADC channel 13 |
| Контакт 34 | PTB0/ADP12 — Port B GPIO 0 / ADC channel 12 |
| Контакт 35 | PTA7/ADP3 — Port A GPIO 7 / ADC channel 3 |
| Контакт 36 | PTA6/ADP2 — Port A GPIO 6 / ADC channel 2 |
| Контакт 37 | PTA5/ADP1 — Port A GPIO 5 / ADC channel 1 |
| Контакт 38 | PTA4/ADP0 — Port A GPIO 4 / ADC channel 0 |
| Контакт 39 | PTA3/ADP15 — Port A GPIO 3 / ADC channel 15 |
| Контакт 40 | PTA1/ADP14 — Port A GPIO 1 / ADC channel 14 |
| Контакт 41 | PTA0/ADP23 — Port A GPIO 0 / ADC channel 23 |
| Контакт 42 | PTA2/TXD1 — Port A GPIO 2 / SCI1 TXD |
| Контакт 43 | PTA3/RXD1 — Port A GPIO 3 / SCI1 RXD (note: collated with pin 39 in some datasheet revs) |
| Контакт 44 | PTA6/KBI1 — Port A GPIO 6 / keyboard interrupt 1 |
| Контакт 45 | PTA7/KBI0 — Port A GPIO 7 / keyboard interrupt 0 |
| Контакт 46 | PTA0/IRQ — Port A GPIO 0 / external IRQ (note: collated with pin 41 in some datasheet revs) |
| Контакт 47 | PTF7 — Port F GPIO 7 |
| Контакт 48 | VDD — Digital supply voltage |
| Контакт 49 | VSS — Digital ground |
| Контакт 50 | PTF6 — Port F GPIO 6 |
| Контакт 51 | PTF5 — Port F GPIO 5 |
| Контакт 52 | PTF4 — Port F GPIO 4 |
| Контакт 53 | CANTX — CAN transmit output |
| Контакт 54 | CANRX — CAN receive input |
| Контакт 55 | PTF3 — Port F GPIO 3 |
| Контакт 56 | PTF2 — Port F GPIO 2 |
| Контакт 57 | PTF1 — Port F GPIO 1 |
| Контакт 58 | PTF0/TXD1 — Port F GPIO 0 / SCI1 TXD |
| Контакт 59 | PTG7 — Port G GPIO 7 |
| Контакт 60 | PTG6 — Port G GPIO 6 |
| Контакт 61 | PTG5 — Port G GPIO 5 |
| Контакт 62 | PTG4 — Port G GPIO 4 |
| Контакт 63 | PTG3 — Port G GPIO 3 |
| Контакт 64 | PTG2 — Port G GPIO 2 |
Типичное применение
MC9S08DZ60ACLH подходит для 6 применениеs: Automotive Body Control Module, HVAC Control Module, Instrument Cluster Display Controller, CAN-Based Sensor Node, Industrial Pump Controller, Battery Management Slave Module.
Automotive Body Control Module
The MC9S08DZ60ACLH is well suited to automotive body controllers because it integrates CAN 2.0A/B, dual SCI, I2C and SPI in a single 64-LQFP package. Its 60KB Flash accommodates CAN/J1939 or CANopen stacks plus door/window/lamp logic, while 4KB on-chip EEPROM stores node IDs, calibration, and fault logs without external parts. Compared with a discrete CAN-IC + external EEPROM + 8-bit MCU solution, the S08DZ60 reduces BOM by two ICs. Hardware interrupt latency at 40MHz is deterministic enough for 1Mbps CAN arbitration, and the -40C to +85C industrial temperature range covers cabin installations. Pair with a TJA1050 or TJA1042 CAN transceiver on the bus side.
Рекомендуется
HVAC Control Module
The MC9S08DZ60ACLH fits residential and commercial HVAC controllers because its 24-channel 12-bit ADC reads multiple analog temperature sensors, pressure transducers, and airflow sensors simultaneously. The 6-channel PWM module drives variable-speed fans, valves, and compressor relays without an external motor-driver. With 2KB RAM and 60KB Flash, the device runs scheduling algorithms, PID control loops, and a Modbus or BACnet slave stack on SCI. The 2.7-5.5V supply range accepts unregulated 5V or 3.3V rails typical of HVAC power supplies. The integrated I2C bus connects to EEPROM-backed RTC and LCD display modules, eliminating auxiliary chips.
Рекомендуется
Instrument Cluster Display Controller
The MC9S08DZ60ACLH serves as a low-cost cluster controller driving stepper-motor gauges or LED bar displays because the 6-channel PWM and 24-channel ADC cover analog sensor inputs (fuel level, oil pressure, temperature) plus PWM dimming of backlights. The CAN interface receives vehicle-speed, RPM, and diagnostic data from the body control module at 500kbps. With 60KB Flash it fits a small RTOS or super-loop scheduler plus gauge calibration tables in 4KB EEPROM. The LQFP-64 10x10mm footprint allows a 2-layer PCB. The integrated BDM enables in-circuit firmware updates without removing the cluster from the panel.
Рекомендуется
CAN-Based Sensor Node
The MC9S08DZ60ACLH is ideal for distributed sensor nodes because the integrated CAN module, 24-channel ADC, and SCI combine into a single-IC node that reads sensors and reports them on the bus. With 4KB EEPROM it stores sensor calibration data persistently; with 60KB Flash it runs the CANopen or DeviceNet slave stack plus sensor-fusion logic. The 53 GPIO allow digital-input expansion to switches, encoders, or expansion I/O expanders via SPI. Low-power STOP and WAIT modes plus 40MHz wake-up make it suitable for wake-on-CAN battery nodes. The BDM pin enables field firmware updates without a bootloader overhead.
Рекомендуется
Industrial Pump Controller
The MC9S08DZ60ACLH drives industrial pump controllers because its 6-channel PWM and 24-channel ADC support variable-frequency drive feedback, motor current sensing, and pressure/flow sensor monitoring. Dual SCI ports handle RS-485 Modbus master/slave and a debug console simultaneously. The 60KB Flash stores the pump control algorithm, dry-run protection, and Modbus register map. Housed in LQFP-64 10x10mm, the IC mounts on a control board with a high-voltage driver section isolated by optocouplers. The -40C to +85C industrial range covers most factory-floor enclosures; pair with an external watchdog supervisor for SIL-2 style redundancy.
Рекомендуется
Battery Management Slave Module
The MC9S08DZ60ACLH serves as a slave cell-monitoring module in a multi-cell Li-ion battery management system (BMS), where each module monitors 6-12 series cells and reports to a master via CAN or SCI. The 24-channel 12-bit ADC reads cell voltages and thermistor inputs, while 4KB EEPROM stores pack parameters and cycle-count data. The 6-channel PWM supports cell-balancing FET control directly without an external driver. Operating from 2.7V-5.5V, the IC is powered from the cell stack via a small LDO. Its 8-bit CISC throughput at 40MHz is sufficient for cell-balancing control plus CAN reporting at 250kbps within 10ms.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для MC9S08DZ60ACLH — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | MC9S08DZ60ACLF | MC9S08DZ60ACLC | S9S08DZ60F2MLHR | MC9S08DZ60AMLH | S9S08DZ96F2VLF |
|---|---|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 64-LQFP (10x10 mm) | 64-LQFP (10x10 mm) - same | 64-LQFP (10x10 mm) - same | 64-LQFP (10x10 mm) - same | 64-LQFP (10x10 mm) - same | 64-LQFP (10x10 mm) - same |
| CPU Frequency | 40 MHz | 40 MHz | 40 MHz | 40 MHz | 40 MHz | 40 MHz |
| Flash Size | 60 KB | 60 KB | 60 KB | 60 KB | 60 KB | 96 KB |
| EEPROM | 4 KB | 4 KB | 4 KB | 4 KB | 4 KB | 4 KB |
| CAN | 1 x CAN 2.0A/B | 1 x CAN 2.0A/B | 1 x CAN 2.0A/B | 1 x CAN 2.0A/B | 1 x CAN 2.0A/B | 1 x CAN 2.0A/B |
| Operating Temperature | -40 C to +85 C | -40 C to +125 C | 0 C to +70 C | -40 C to +85 C | -40 C to +105 C | -40 C to +85 C |
| AEC-Q100 | Not qualified (NRND) | AEC-Q100 grade 0 | Not qualified | AEC-Q100 grade 1 | Not qualified | AEC-Q100 grade 1 |
| Lifecycle Status | NRND | Active | Active | Active | Active | Active |
Ключевые отличия
- Integrated CAN 2.0A/B module with 4KB EEPROM in single chip (против MC908AP8CBE (HC08, 8MHz, no CAN, no EEPROM))
- 40MHz CPU with industrial temperature spec (против MC9S08SH4CTL (50MHz Cortex-M0, 32-bit))
- Mask-set refresh with active lifecycle (против MC9S08DZ60ACLH (NRND))
Заметки по проектированию
Place a 100nF ceramic decoupling capacitor on each VDD/VSS pair (pins 16/17, 48/49) as close to the IC as possible, plus a single 10uF bulk capacitor on the VDD rail. The MC9S08DZ60ACLH has multiple VDD/VSS pairs to reduce internal ground bounce; missing even one pair risks ADC accuracy degradation. Estimated: at 40MHz CPU with all peripherals active, supply current is approximately 30mA, plus 5mA per active ADC channel during conversion.
Route the BKGD/MS pin (pin 1) directly to a 2x3 0.1in header for BDM programming; do not place any capacitor on this line. Keep the CAN TX/RX traces (pins 53/54) short - within 25mm - and route them as a differential pair to the CAN transceiver, with 100ohm differential impedance. Add a 4.7kohm pull-up on RESET (pin 8) and a 1N5819 diode from VDD to RESET for power-on reset. Decoupling capacitors must be on the IC side of any ferrite on the CAN bus.
Do not pull BKGD high during reset before the firmware initializes the pin mode, or the device may enter factory mode unintentionally. ADC channel pins are not 5V-tolerant on the VREF reference input - use the dedicated VREF pin instead if a 5V reference is required. The CAN module requires a transceiver - it cannot drive the bus directly. The 4KB EEPROM has a 100k-cycle endurance limit per byte; avoid using EEPROM bytes as frequently-updated counters.
When driving long cables from the SCI (UART) pins, add a series 22-ohm resistor plus ESD protection diode array. The 24-channel 12-bit ADC achieves its 2.5us conversion only when the ADC clock is at 8MHz or below; do not exceed this or linearity worsens. For mixed-signal layouts, isolate the analog VDD/VSS pair from digital VDD/VSS with a ferrite bead, and place a guard ring around the ADC reference traces.
Информация о соответствии
RoHS and lead-free per NXP product page. MC9S08DZ60ACLH itself is not AEC-Q100 qualified - choose MC9S08DZ60ACLF for AEC-Q100 grade 0 (automotive underhood) or S9S08DZ60F2MLHR for AEC-Q100 grade 1. Halogen-free status not stated on the NXP product page.