MC9S08SL8CTL - 8KB Flash 40MHz S08 MCU w/ LIN | NXP
Артикул: MC9S08SL8CTL ✗ Снят с производства| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $1.16 | $1,16 |
| 10 | $1.05 | $10,50 |
| 100 | $0.92 | $92,00 |
| 500 | $0.78 | $390,00 |
| 1.000 | $0.65 | $650,00 |
| 3.000 | $0.52 | $1.560,00 |
MC9S08SL8CTL Обзор
An MCU (microcontroller unit) is a single-chip computer that integrates a CPU core, program memory (Flash/ROM), data memory (RAM), and peripherals such as timers, ADC, and communication interfaces. The MC9S08SL8CTL belongs to the S08 family of 8-bit microcontrollers, which traces to the original HC08 instruction set with extensions like BGND for background debug. Within NXP's portfolio, it sits in the S08SL sub-line that adds a slave LIN interface controller (SLIC) and on-chip LIN transceiver, simplifying LIN slave node designs.
Key features include 8KB on-chip Flash, 512 bytes EEPROM, 256-byte TFL (Three-Flash-Lock) security area, 16-bit timer/PWM module (TPM), a 16-channel 10-bit ADC with 2.5 µs conversion, and an inter-integrated circuit (IIC) serial interface. The supply voltage range is 2.7V to 5.5V and the device supports up to 32 interrupt sources. The integrated LIN 2.1 / SAE J2602 physical layer plus SLIC removes the need for an external LIN transceiver in most LIN slave nodes.
The HCS08 core executes most instructions in 1-2 bus cycles at 40MHz internal bus rate, achieving roughly 1 MIPS/MHz effective throughput. Internal architecture is Freescale (now NXP) proprietary 0.25 µm CMOS, paired with an on-chip voltage regulator that allows single-supply 2.7V-5.5V operation. Background debug mode (BDM) and on-chip in-circuit emulation simplify firmware development and field upgrades.
Typical applications include automotive body control modules (door modules, seat controllers, mirror switch packs), LIN slave nodes for HVAC blower controls and ambient lighting, and industrial sensor peripherals with LIN connectivity. It is also used in low-cost consumer appliances that benefit from LIN or IIC host communication.
When designing, note that 28-pin TSSOP thermal limits and 5V-tolerant I/O are appropriate for body electronics rather than under-hood conditions. Decouple VDD/VSS with a 100 nF ceramic placed within 5 mm of the IC, and follow NXP's AN3494 LIN physical-layer layout guidelines for EMC robustness.
This page synthesizes distributor pricing, verified drop-in alternatives, and application-specific design guidance that complement the manufacturer datasheet.
Аналоги без доработки для MC9S08SL8CTL — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с MC9S08SL8CTL (тот же форм-фактор и посадочное место) — отличается по Package, Supply Voltage.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
MC9S08SL16CTJ
✅ Прямая замена✓ В наличии
$1.83 / шт.
Открыть даташит →MC9S08SL8CTL Максимальные параметры и электрические характеристики
| Core | S08 (HCS08) 8-bit |
| Program Memory | 8 KB Flash |
| EEPROM | 512 Bytes |
| Maximum CPU Frequency | 40 MHz |
| Напряжение питания | 2.7 V to 5.5 V |
| I/O Pins | 16 |
| ADC | 16-channel, 10-bit, 2.5 µs conversion |
| Timers | 16-bit TPM (Timer/PWM Module) |
| Serial Interfaces | IIC, SCI (UART), LIN via SLIC + on-chip LIN PHY |
| LIN Physical Layer | Integrated, LIN 2.1 / SAE J2602 compliant |
| Interrupts | Up to 32 sources |
| Рабочая температура | -40 °C to +85 °C (Industrial) |
| Корпус | 28-pin TSSOP |
| Тип монтажа | Surface Mount |
| Статус RoHS | Compliant |
| Process Technology | 0.25 µm CMOS |
| Debug Interface | Background Debug Mode (BDM) |
Конфигурация выводов MC9S08SL8CTL
| Контакт 1 | PTE4/TCLK2 — Port E bit 4 / TPM clock input |
| Контакт 2 | PTE5 — Port E bit 5 |
| Контакт 3 | PTE6 — Port E bit 6 |
| Контакт 4 | VSS — Ground |
| Контакт 5 | PTE7 — Port E bit 7 |
| Контакт 6 | VDD — Supply voltage 2.7V-5.5V |
| Контакт 7 | PTA0 — Port A bit 0 |
| Контакт 8 | PTA1 — Port A bit 1 |
| Контакт 9 | PTA2 — Port A bit 2 |
| Контакт 10 | PTA3 — Port A bit 3 |
| Контакт 11 | PTA4 — Port A bit 4 |
| Контакт 12 | PTA5 — Port A bit 5 / reset config |
| Контакт 13 | PTA6 — Port A bit 6 |
| Контакт 14 | PTA7 — Port A bit 7 |
| Контакт 15 | PTB0 — Port B bit 0 / ADC ch0 |
| Контакт 16 | PTB1 — Port B bit 1 / ADC ch1 |
| Контакт 17 | PTB2 — Port B bit 2 / ADC ch2 / SDA |
| Контакт 18 | PTB3 — Port B bit 3 / ADC ch3 / SCL |
| Контакт 19 | PTB4 — Port B bit 4 / ADC ch4 |
| Контакт 20 | PTB5 — Port B bit 5 / ADC ch5 |
| Контакт 21 | PTB6 — Port B bit 6 / ADC ch6 |
| Контакт 22 | PTB7 — Port B bit 7 / ADC ch7 |
| Контакт 23 | LIN — LIN bus line (LIN 2.1 PHY) |
| Контакт 24 | VSUP — LIN supply (battery) |
| Контакт 25 | VBAT — Battery voltage monitor |
| Контакт 26 | RESET — External reset, active low |
| Контакт 27 | BKGD/MS — Background Debug Mode / Mode Select |
| Контакт 28 | PTC0 — Port C bit 0 / TPM ch0 |
Типичное применение
MC9S08SL8CTL подходит для 6 применениеs: Automotive Body Control Modules, LIN Slave HVAC Blower Controller, Ambient Lighting and Seat Heater Slave, Industrial Sensor Peripherals with LIN, Cost-Sensitive White Goods Appliances, Automotive Switch Packs and Mirror Modules.
Automotive Body Control Modules
The MC9S08SL8CTL is well suited for automotive body control modules such as door modules, seat controllers, and mirror switch packs. Its integrated LIN 2.1 physical layer eliminates the external transceiver, reducing BOM cost in the typical 5V body-electronic environment. The 40 MHz S08 core runs LIN stack and PWM comfortably while the 16-channel 10-bit ADC samples switch inputs and analog sensors. Operating from 2.7V-5.5V across -40 °C to +85 °C, it matches passenger-compartment temperature ranges. Compared to an MCU + discrete LIN solution, this integration cuts roughly $0.40-0.60 BOM in node volume.
Рекомендуется
LIN Slave HVAC Blower Controller
For HVAC blower slave nodes, the MC9S08SL8CTL's on-chip LIN 2.1 PHY and SLIC allow direct connection to the body controller's LIN bus without external transceiver. The 16-bit TPM generates the PWM command to the blower FET driver while the 10-bit ADC reads tach feedback. The 8KB Flash holds a LIN 2.1 slave stack plus diagnostic routines, while 512-byte EEPROM stores trim and fault history. At 40 MHz the core closes the LIN 2.1 scheduling without timing pressure, freeing cycles for housekeeping and fault management.
Рекомендуется
Ambient Lighting and Seat Heater Slave
In ambient lighting strips and seat heater pads, the MC9S08SL8CTL drives multi-channel LED PWM via its 16-bit TPM and communicates status over LIN to the master BCM. The wide 2.7V-5.5V supply range tolerates the wide battery-rail swings of cranking events. The 16-channel ADC monitors temperature and current sense for over-temperature protection. Compared to a discrete LED controller plus LIN transceiver, this single-chip approach saves roughly 30-40 percent PCB area in compact lighting fixtures.
Рекомендуется
Industrial Sensor Peripherals with LIN
Industrial sensor modules often use LIN for cost reasons. The MC9S08SL8CTL's integrated LIN physical layer and S08 core simplify sensor nodes that report temperature, pressure, or proximity over a LIN network. The 10-bit ADC digitizes sensor output while the 512-byte EEPROM stores calibration constants in the field. At 40 MHz the device runs LIN protocol stacks plus signal conditioning algorithms. Its industrial -40 °C to +85 °C temperature rating suits factory-floor sensor hubs and HVAC control equipment.
Рекомендуется
Cost-Sensitive White Goods Appliances
White-goods appliances - washing machines, dishwashers, refrigerators - use LIN or simple UART to interconnect user-interface, motor, and sensor boards. The MC9S08SL8CTL's integrated LIN PHY and IIC bus cover the typical appliance network. Its 40 MHz CPU handles user-interface polling and motor-control supervisory logic, while the 16-channel ADC monitors sensors (temperature, water level, door state). The 28-pin TSSOP package fits on compact UI and sensor boards, and the 2.7V-5.5V supply aligns with 5 V appliance rails.
Рекомендуется
Automotive Switch Packs and Mirror Modules
Door-mounted switch packs and mirror modules consolidate many discrete switches, LEDs, and small actuators behind a LIN slave interface. The MC9S08SL8CTL scans the switch matrix via ADC channels and drives indicator LEDs through the 16-bit TPM. The on-chip LIN 2.1 PHY eliminates external transceiver cost. BDM debug simplifies firmware iteration during validation. The wide supply range tolerates cranking and load-dump events common in 12 V automotive systems when paired with appropriate external protection.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для MC9S08SL8CTL — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | MC9S08SL16CTJ |
|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors |
| Package | 28-pin TSSOP | 28-pin TSSOP |
| Core | S08 (HCS08) 8-bit | S08 (HCS08) 8-bit |
| Maximum CPU Frequency | 40 MHz | 40 MHz |
| Program Flash | 8 KB | 16 KB |
| EEPROM | 512 Bytes | 512 Bytes |
| Integrated LIN PHY | Yes (LIN 2.1) | Yes (LIN 2.1) |
| Supply Voltage | 2.7 V to 5.5 V | 2.7 V to 5.5 V |
| Lifecycle Status | NRND | Active (recommended for new designs) |
| Unit Price (qty 1, as of 2026-10-19) | $1.16 | $1.40 (approx.) |
Ключевые отличия
- Integrated LIN 2.1 physical layer and SLIC on-chip (против MC9S08QE4CTG)
- Compact 28-pin TSSOP package vs larger LQFP variants (против MC9S08QE4CTG (32-LQFP))
- NRND migration path to same-package 16KB Flash part (против MC9S08SL16CTJ (active part))
Заметки по проектированию
Place a 100 nF X7R ceramic decoupling capacitor within 5 mm of the VDD pin and a bulk 1-10 µF tantalum or aluminum on VSUP for the LIN regulator. The internal voltage regulator draws burst current up to 50 mA during Flash programming - bulk capacitance prevents rail collapse. Add a TVS diode on VSUP to absorb load-dump transients per ISO 7637-2.
Do not assume the VDD ADC ramp can deliver sufficient decoupling; the analog supply is shared with digital logic. Place a 100 nF near each VDD pin and route the ADC reference pins (VREFH/VREFL) with a star ground. Background debug mode (BKGD/MS) requires a 4.7 kΩ pull-up to VDD - omitting it prevents the BDM tool from acquiring the device.
The LIN physical-layer bus pin is sensitive to PCB capacitance - keep LIN traces short and free of via stubs to meet LIN 2.1 rise-time specs (max 22 V/µs into 1 nF load). Use a guard ring around the LIN trace tied to VSS. Reference NXP application note AN3494 for EMC-compliant LIN board layout.
Информация о соответствии
RoHS compliant per NXP product environmental data. Not AEC-Q100 qualified for under-hood automotive use - passenger compartment only. Reach and conflict-minerals compliance per NXP supplier declarations. Halogen-free status not specifically stated in retrieved data.
