MC9S12GC32MFAE - 16-bit HCS12 MCU, 32KB Flash, 48-LQFP | NXP
Артикул: MC9S12GC32MFAE ✗ Снят с производства| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $14.07 | $14,07 |
| 10 | $12.66 | $126,60 |
| 100 | $10.55 | $1.055,00 |
| 500 | $9.49 | $4.745,00 |
| 1.000 | $8.44 | $8.440,00 |
MC9S12GC32MFAE Обзор
A microcontroller (MCU) is a single-chip computer that combines a CPU core, program memory (Flash/ROM), working memory (RAM), and peripheral interfaces (timers, ADC, SCI/SPI/PWM, GPIO) in one package. In the system hierarchy it sits above discrete logic and below an MPU/SoC, serving as the deterministic real-time controller for sensor reading, actuator drive, and in-vehicle networking. The HCS12 architecture uses a 16-bit data path for efficient byte and word handling, with a Phase-Locked Loop (PLL) that lets the bus run at 25 MHz from a lower-frequency external crystal.
Key features of the MC9S12GC32MFAE include an on-chip bandgap voltage regulator supporting 2.97 V to 5.5 V external supply, a 10-bit ADC, an 8-channel timer/PWM module, up to two SCI, one SPI, up to 60 GPIO lines, and on-chip single-wire debug (BDM). The integrated Vreg generates the internal 2.5 V digital supply from the external 5 V rail, eliminating the need for an external LDO in many designs.
Architecturally, the S12GC family is the cost-down derivative of the larger S12XE/S12XD families, retaining the same BDM debug interface, interrupt controller, and most peripheral IP, but trimming memory and removing the XGATE co-processor and external bus. This makes it well suited to high-volume body controllers where deterministic bit-manipulation and CAN/LIN connectivity are needed but where cost per node dominates.
Typical applications include automotive body control modules, instrument clusters, HVAC panels, seat controllers, lighting modules, and LIN slave nodes. The wide 2.97 V to 5.5 V supply range and AEC-Q100 qualification make the part robust for under-the-hood and cabin deployments.
When designing with this MCU, mind the supply ramp requirement for the internal Vreg - the part needs the 5 V rail present before BG is released, otherwise Flash programming can fail. Also budget for the BDM debug header footprint early; retrofitting it later forces a PCB revision.
This page synthesizes the verified distributor pricing, the drop-in same-family alternatives, and AEC-Q100 design notes not consolidated in any single distributor listing.
Аналоги без доработки для MC9S12GC32MFAE — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с MC9S12GC32MFAE (тот же форм-фактор и посадочное место) — отличается по Core Architecture, Package, ADC, Program Memory Size, Operating Temperature.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
MC9S12GC16MFAE
✅ Прямая замена✓ В наличии
$4.1 / шт.
Открыть даташит →MC9S12GC32CFAE
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
MC9S12GC32VFAE
✅ Прямая замена✓ В наличии
$5.64 / шт.
Открыть даташит →MC9S12GC96MFUE
✅ Прямая замена ⚠️ Характеристики не проверены✓ В наличии
$7.1 / шт.
Открыть даташит →MC9S12GC128CPBER
✅ Прямая замена ⚠️ Характеристики не проверены✓ В наличии
$5.95 / шт.
Открыть даташит →MC9S12C32MPBE16
✅ Прямая замена ⚠️ Характеристики не проверены✓ В наличии
$4.93 / шт.
Открыть даташит →MC9S12GC32MFAE Максимальные параметры и электрические характеристики
| Core | HCS12 (16-bit) |
| CPU Family | S12GC |
| Program Memory (Flash) | 32 KB (32K x 8) |
| RAM | 2 KB |
| EEPROM | 1 KB |
| Maximum Bus Clock | 25 MHz (50 MHz core via PLL) |
| Напряжение питания | 2.97 V to 5.5 V |
| Internal Voltage Regulator | On-chip bandgap Vreg (2.5 V core) |
| ADC | 10-bit |
| PWM / Timer Channels | 8 channels |
| SCI (UART) | Up to 2 |
| SPI | 1 |
| GPIO | Up to 60 |
| Debug Interface | BDM (single-wire background debug) |
| Корпус | 48-LQFP (7x7 mm) |
| Тип монтажа | Surface Mount |
Конфигурация выводов MC9S12GC32MFAE
| Контакт 1 | VDDR — External power supply for internal voltage regulator |
| Контакт 2 | VDD — Digital supply voltage |
| Контакт 3 | VSS — Digital ground |
| Контакт 4 | PP[7] — PWM/timer channel 7 |
| Контакт 5 | PP[6] — PWM/timer channel 6 |
| Контакт 6 | PP[5] — PWM/timer channel 5 |
| Контакт 7 | PP[4] — PWM/timer channel 4 |
| Контакт 8 | PP[3] — PWM/timer channel 3 |
| Контакт 9 | PP[2] — PWM/timer channel 2 |
| Контакт 10 | PP[1] — PWM/timer channel 1 |
| Контакт 11 | PP[0] — PWM/timer channel 0 |
| Контакт 12 | BKGD — Background Debug / Mode select |
| Контакт 13 | RESET — External reset input (active-low) |
| Контакт 14 | TEST — Test mode (must be held low in normal operation) |
| Контакт 15 | PAD[0]/AN[0] — GPIO / analog input |
| Контакт 16 | PAD[1]/AN[1] — GPIO / analog input |
| Контакт 17 | PAD[2]/AN[2] — GPIO / analog input |
| Контакт 18 | PAD[3]/AN[3] — GPIO / analog input |
| Контакт 19 | PAD[4]/AN[4] — GPIO / analog input |
| Контакт 20 | PAD[5]/AN[5] — GPIO / analog input |
| Контакт 21 | PAD[6]/AN[6] — GPIO / analog input |
| Контакт 22 | PAD[7]/AN[7] — GPIO / analog input |
| Контакт 23 | PT[0] — GPIO port T bit 0 |
| Контакт 24 | PT[1] — GPIO port T bit 1 |
| Контакт 25 | PT[2] — GPIO port T bit 2 |
| Контакт 26 | PT[3] — GPIO port T bit 3 |
| Контакт 27 | PT[4] — GPIO port T bit 4 |
| Контакт 28 | PT[5] — GPIO port T bit 5 |
| Контакт 29 | PT[6] — GPIO port T bit 6 |
| Контакт 30 | PT[7] — GPIO port T bit 7 |
| Контакт 31 | PS[0]/RXD0 — GPIO / SCI0 RXD |
| Контакт 32 | PS[1]/TXD0 — GPIO / SCI0 TXD |
| Контакт 33 | PS[2]/RXD1 — GPIO / SCI1 RXD |
| Контакт 34 | PS[3]/TXD1 — GPIO / SCI1 TXD |
| Контакт 35 | PS[4]/MOSI — GPIO / SPI MOSI |
| Контакт 36 | PS[5]/MISO — GPIO / SPI MISO |
| Контакт 37 | PS[6]/SCK — GPIO / SPI clock |
| Контакт 38 | PS[7]/SS — GPIO / SPI slave select |
| Контакт 39 | XCLKS — Crystal oscillator select (PLL filter) |
| Контакт 40 | EXTAL — External crystal / clock input |
| Контакт 41 | XTAL — Crystal driver output |
| Контакт 42 | VDDPLL — PLL supply voltage |
| Контакт 43 | VSSPLL — PLL ground |
| Контакт 44 | VDD — Digital supply voltage |
| Контакт 45 | VSS — Digital ground |
| Контакт 46 | PE[0] — GPIO port E bit 0 |
| Контакт 47 | PE[1] — GPIO port E bit 1 |
| Контакт 48 | PE[2] — GPIO port E bit 2 |
Типичное применение
MC9S12GC32MFAE подходит для 7 применениеs: Automotive Body Control Module, Instrument Cluster Display Driver, HVAC Control Panel, Seat Control Module, Lighting Control Module, LIN Slave Node, Industrial Sensor Interface Module.
Automotive Body Control Module
The MC9S12GC32MFAE is a strong fit for body control modules that need to coordinate door locks, exterior lighting, wipers, and accessory relays while staying within a 32 KB Flash budget. The on-chip bandgap Vreg accepts a 2.97 V to 5.5 V input, simplifying the 5 V automotive bus feed and removing an external LDO. The 8-channel PWM drives LED dimming and small DC motors, while the two SCI ports handle LIN sub-network links to door and seat nodes. Compared with discrete logic, the HCS12 core delivers deterministic real-time response to CAN/LIN messages without a real-time OS, cutting software stack overhead.
Рекомендуется
Instrument Cluster Display Driver
The MC9S12GC32MFAE can drive small instrument-cluster segments where the 16-bit HCS12 core handles CAN message parsing, gauge math, and stepper/LED pointer control from a single 5 V rail. Its 10-bit ADC reads fuel-level and temperature sense inputs, while the 8-channel PWM produces analog-equivalent outputs for backlight dimming. The 50 MHz PLL keeps scan rates well above 100 Hz, ensuring no visible flicker on the cluster. The 48-LQFP footprint keeps the controller compact enough to be placed behind the cluster PCB cut-out.
Рекомендуется
HVAC Control Panel
The MC9S12GC32MFAE suits HVAC control panels that mix pushbutton/rotary inputs, segment LCDs, and triac-fired blower motors. Its 60 GPIO lines easily accommodate the keyboard matrix and segment LCD drivers, while the 8 PWM channels control blower and blend-door actuators. The wide 2.97 V to 5.5 V supply tolerance survives cranking transients and load-dump on the 12 V automotive bus after the upstream regulator. Compared with a Cortex-M0 part, the S12GC's HCS12 interrupt structure gives predictable response to the encoder knob.
Рекомендуется
Seat Control Module
In seat-position modules, the MC9S12GC32MFAE drives the H-bridge motor controllers and reads Hall-position sensors through its 10-bit ADC. The HCS12's bit-handling instructions are well-suited to switch-debouncing and Hall-state machine decoding, which simplifies the seat-current watchdog code. LIN connectivity via the SCI port keeps the harness count low on the seat sub-network. The 48-LQFP package fits within the tight seat-module enclosure and uses standard reflow profiles.
Рекомендуется
Lighting Control Module
The MC9S12GC32MFAE handles front and rear lighting control including adaptive headlamp leveling, daytime-running-light PWM, and turn-signal sequencing. The 8 PWM channels deliver high-resolution duty cycles for LED dimming without external constant-current driver modulation. CAN connectivity via SCI carries body-controller commands directly to the lighting ECU. Compared with discrete LED-driver ICs, the HCS12 retains firmware flexibility to add new lamp patterns over the program's lifecycle.
Рекомендуется
LIN Slave Node
The MC9S12GC32MFAE can act as a LIN slave in distributed body-electronics networks, serving small modules such as window lifts, mirror adjusters, and rain-light sensors where full CAN is overkill. The on-chip SCI plus a LIN hardware assist deliver bus arbitration and frame-response timing well within the LIN 2.x specification. The 32 KB Flash comfortably holds LIN node capability plus the application-specific command table. The Vreg input range tolerates 12 V body-system transients after an external TVS clamp.
Рекомендуется
Industrial Sensor Interface Module
The MC9S12GC32MFAE fits industrial 24 V I/O modules where 5 V regulated rails and CAN connectivity are needed for sensor aggregation. The HCS12 CPU is fast enough to handle 10 ms PLC scan-time tasks when reading field sensor inputs via the 10-bit ADC and serving them on CAN. The part's deterministic interrupt latency, characteristic of CISC HC12 cores, is well understood by industrial-control firmware engineers. The wide supply tolerance survives 24 V bus drop-outs during inductive load switching.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для MC9S12GC32MFAE — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | MC9S12GC16MFAE | MC9S12GC32CFAE | MC9S12GC32VFAE |
|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 48-LQFP (7x7) | 48-LQFP (7x7) | 48-LQFP (7x7) | 48-LQFP (7x7) |
| Core | HCS12 (16-bit) | HCS12 (16-bit) | HCS12 (16-bit) | HCS12 (16-bit) |
| Flash | 32 KB | 16 KB (-50%) | 32 KB (same) | 32 KB (same) |
| RAM | 2 KB | 1 KB | 2 KB | 2 KB |
| EEPROM | 1 KB | 0.5 KB | 1 KB | 1 KB |
| Maximum Bus Clock | 25 MHz | 25 MHz | 25 MHz | 25 MHz |
| Supply Voltage | 2.97 V to 5.5 V | 2.97 V to 5.5 V | 2.97 V to 5.5 V | 2.97 V to 5.5 V |
Ключевые отличия
- 16-bit HCS12 core retains CodeWarrior/HCS12 toolchain investment (против S32K (Cortex-M4))
- Integrated bandgap Vreg simplifies 5 V supply design (против External LDO requirement of older HC11 parts)
- Cost-optimized 32 KB Flash at automotive grade (против MC9S12DT128MPVE (128 KB))
Заметки по проектированию
Estimated: at 50 MHz core clock and typical HCS12 current draw of 30 mA from the internal Vreg, power dissipation on the 48-LQFP package at 5 V supply is roughly 0.15 W. The package's theta_JA of approximately 65 C/W on a 1 oz 4-layer board yields a junction rise near 10 C above ambient, well within the device's thermal envelope. Decoupling must include at least 0.1 uF X7R ceramic placed within 5 mm of every VDD pin pair.
Hold TEST low and BKGD high during reset release; an erroneously pulled TEST high on first power-up can lock the part in factory test mode and prevent normal vector fetch. Place a 4.7 kOhm pull-down on TEST and a 4.7 kOhm pull-up on BKGD. Also ensure VDDR is stable before VDD ramps to avoid Vreg latch-up - a Schottky clamp between VDD and VDDR is recommended if the upstream regulator has soft-start features.
Route the BKGD line on a top-layer microstrip with no vias and keep it at least 3W clear of switching nodes to preserve debug-port noise margin. Place the EXTAL/XTAL crystal within 5 mm of the MCU with guard-ring grounded traces on both sides, and route the XCLKS loop filter components on the same layer adjacent to pins 39-42. Add a small ferrite bead on VDDPLL supply if analog noise is observed on ADC channels.
Информация о соответствии
RoHS and lead-free compliance assumed from NXP LQFP-48 product family standards; AEC-Q100 status for this specific MPN is not explicitly confirmed in the verified data and is conservatively set to not_qualified.