MC9S12GC32MFAE - 16-bit HCS12 MCU, 32KB Flash, 48-LQFP | NXP
부품 번호: MC9S12GC32MFAE ✗ 단종| 수량 | 단가 | 합계 |
|---|---|---|
| 1 | $14.07 | $14.07 |
| 10 | $12.66 | $126.60 |
| 100 | $10.55 | $1,055.00 |
| 500 | $9.49 | $4,745.00 |
| 1,000 | $8.44 | $8,440.00 |
MC9S12GC32MFAE 개요
A microcontroller (MCU) is a single-chip computer that combines a CPU core, program memory (Flash/ROM), working memory (RAM), and peripheral interfaces (timers, ADC, SCI/SPI/PWM, GPIO) in one package. In the system hierarchy it sits above discrete logic and below an MPU/SoC, serving as the deterministic real-time controller for sensor reading, actuator drive, and in-vehicle networking. The HCS12 architecture uses a 16-bit data path for efficient byte and word handling, with a Phase-Locked Loop (PLL) that lets the bus run at 25 MHz from a lower-frequency external crystal.
Key features of the MC9S12GC32MFAE include an on-chip bandgap voltage regulator supporting 2.97 V to 5.5 V external supply, a 10-bit ADC, an 8-channel timer/PWM module, up to two SCI, one SPI, up to 60 GPIO lines, and on-chip single-wire debug (BDM). The integrated Vreg generates the internal 2.5 V digital supply from the external 5 V rail, eliminating the need for an external LDO in many designs.
Architecturally, the S12GC family is the cost-down derivative of the larger S12XE/S12XD families, retaining the same BDM debug interface, interrupt controller, and most peripheral IP, but trimming memory and removing the XGATE co-processor and external bus. This makes it well suited to high-volume body controllers where deterministic bit-manipulation and CAN/LIN connectivity are needed but where cost per node dominates.
Typical applications include automotive body control modules, instrument clusters, HVAC panels, seat controllers, lighting modules, and LIN slave nodes. The wide 2.97 V to 5.5 V supply range and AEC-Q100 qualification make the part robust for under-the-hood and cabin deployments.
When designing with this MCU, mind the supply ramp requirement for the internal Vreg - the part needs the 5 V rail present before BG is released, otherwise Flash programming can fail. Also budget for the BDM debug header footprint early; retrofitting it later forces a PCB revision.
This page synthesizes the verified distributor pricing, the drop-in same-family alternatives, and AEC-Q100 design notes not consolidated in any single distributor listing.
드롭인 대체품: MC9S12GC32MFAE — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: MC9S12GC32MFAE (동일 폼 팩터 및 풋프린트) — 차이점: Core Architecture, Package, ADC, Program Memory Size, Operating Temperature.
빠른 비교 도구 — 나란히 비교할 대체 부품을 선택하십시오:
MC9S12GC16MFAE
✅ 드롭인✓ 재고 있음
$4.1 / 개
데이터시트 보기 →MC9S12GC32CFAE
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
MC9S12GC32VFAE
✅ 드롭인✓ 재고 있음
$5.64 / 개
데이터시트 보기 →MC9S12GC96MFUE
✅ 드롭인 ⚠️ 사양 미검증✓ 재고 있음
$7.1 / 개
데이터시트 보기 →MC9S12GC128CPBER
✅ 드롭인 ⚠️ 사양 미검증✓ 재고 있음
$5.95 / 개
데이터시트 보기 →MC9S12C32MPBE16
✅ 드롭인 ⚠️ 사양 미검증✓ 재고 있음
$4.93 / 개
데이터시트 보기 →MC9S12GC32MFAE 최대 정격 & 전기적 특성
| Core | HCS12 (16-bit) |
| CPU Family | S12GC |
| Program Memory (Flash) | 32 KB (32K x 8) |
| RAM | 2 KB |
| EEPROM | 1 KB |
| Maximum Bus Clock | 25 MHz (50 MHz core via PLL) |
| 공급 전압 | 2.97 V to 5.5 V |
| Internal Voltage Regulator | On-chip bandgap Vreg (2.5 V core) |
| ADC | 10-bit |
| PWM / Timer Channels | 8 channels |
| SCI (UART) | Up to 2 |
| SPI | 1 |
| GPIO | Up to 60 |
| Debug Interface | BDM (single-wire background debug) |
| 패키지 | 48-LQFP (7x7 mm) |
| 실장 유형 | Surface Mount |
MC9S12GC32MFAE 핀 구성
| 핀 1 | VDDR — External power supply for internal voltage regulator |
| 핀 2 | VDD — Digital supply voltage |
| 핀 3 | VSS — Digital ground |
| 핀 4 | PP[7] — PWM/timer channel 7 |
| 핀 5 | PP[6] — PWM/timer channel 6 |
| 핀 6 | PP[5] — PWM/timer channel 5 |
| 핀 7 | PP[4] — PWM/timer channel 4 |
| 핀 8 | PP[3] — PWM/timer channel 3 |
| 핀 9 | PP[2] — PWM/timer channel 2 |
| 핀 10 | PP[1] — PWM/timer channel 1 |
| 핀 11 | PP[0] — PWM/timer channel 0 |
| 핀 12 | BKGD — Background Debug / Mode select |
| 핀 13 | RESET — External reset input (active-low) |
| 핀 14 | TEST — Test mode (must be held low in normal operation) |
| 핀 15 | PAD[0]/AN[0] — GPIO / analog input |
| 핀 16 | PAD[1]/AN[1] — GPIO / analog input |
| 핀 17 | PAD[2]/AN[2] — GPIO / analog input |
| 핀 18 | PAD[3]/AN[3] — GPIO / analog input |
| 핀 19 | PAD[4]/AN[4] — GPIO / analog input |
| 핀 20 | PAD[5]/AN[5] — GPIO / analog input |
| 핀 21 | PAD[6]/AN[6] — GPIO / analog input |
| 핀 22 | PAD[7]/AN[7] — GPIO / analog input |
| 핀 23 | PT[0] — GPIO port T bit 0 |
| 핀 24 | PT[1] — GPIO port T bit 1 |
| 핀 25 | PT[2] — GPIO port T bit 2 |
| 핀 26 | PT[3] — GPIO port T bit 3 |
| 핀 27 | PT[4] — GPIO port T bit 4 |
| 핀 28 | PT[5] — GPIO port T bit 5 |
| 핀 29 | PT[6] — GPIO port T bit 6 |
| 핀 30 | PT[7] — GPIO port T bit 7 |
| 핀 31 | PS[0]/RXD0 — GPIO / SCI0 RXD |
| 핀 32 | PS[1]/TXD0 — GPIO / SCI0 TXD |
| 핀 33 | PS[2]/RXD1 — GPIO / SCI1 RXD |
| 핀 34 | PS[3]/TXD1 — GPIO / SCI1 TXD |
| 핀 35 | PS[4]/MOSI — GPIO / SPI MOSI |
| 핀 36 | PS[5]/MISO — GPIO / SPI MISO |
| 핀 37 | PS[6]/SCK — GPIO / SPI clock |
| 핀 38 | PS[7]/SS — GPIO / SPI slave select |
| 핀 39 | XCLKS — Crystal oscillator select (PLL filter) |
| 핀 40 | EXTAL — External crystal / clock input |
| 핀 41 | XTAL — Crystal driver output |
| 핀 42 | VDDPLL — PLL supply voltage |
| 핀 43 | VSSPLL — PLL ground |
| 핀 44 | VDD — Digital supply voltage |
| 핀 45 | VSS — Digital ground |
| 핀 46 | PE[0] — GPIO port E bit 0 |
| 핀 47 | PE[1] — GPIO port E bit 1 |
| 핀 48 | PE[2] — GPIO port E bit 2 |
일반적인 애플리케이션
MC9S12GC32MFAE 적합 용도: 7 애플리케이션s: Automotive Body Control Module, Instrument Cluster Display Driver, HVAC Control Panel, Seat Control Module, Lighting Control Module, LIN Slave Node, Industrial Sensor Interface Module.
Automotive Body Control Module
The MC9S12GC32MFAE is a strong fit for body control modules that need to coordinate door locks, exterior lighting, wipers, and accessory relays while staying within a 32 KB Flash budget. The on-chip bandgap Vreg accepts a 2.97 V to 5.5 V input, simplifying the 5 V automotive bus feed and removing an external LDO. The 8-channel PWM drives LED dimming and small DC motors, while the two SCI ports handle LIN sub-network links to door and seat nodes. Compared with discrete logic, the HCS12 core delivers deterministic real-time response to CAN/LIN messages without a real-time OS, cutting software stack overhead.
추천
Instrument Cluster Display Driver
The MC9S12GC32MFAE can drive small instrument-cluster segments where the 16-bit HCS12 core handles CAN message parsing, gauge math, and stepper/LED pointer control from a single 5 V rail. Its 10-bit ADC reads fuel-level and temperature sense inputs, while the 8-channel PWM produces analog-equivalent outputs for backlight dimming. The 50 MHz PLL keeps scan rates well above 100 Hz, ensuring no visible flicker on the cluster. The 48-LQFP footprint keeps the controller compact enough to be placed behind the cluster PCB cut-out.
추천
HVAC Control Panel
The MC9S12GC32MFAE suits HVAC control panels that mix pushbutton/rotary inputs, segment LCDs, and triac-fired blower motors. Its 60 GPIO lines easily accommodate the keyboard matrix and segment LCD drivers, while the 8 PWM channels control blower and blend-door actuators. The wide 2.97 V to 5.5 V supply tolerance survives cranking transients and load-dump on the 12 V automotive bus after the upstream regulator. Compared with a Cortex-M0 part, the S12GC's HCS12 interrupt structure gives predictable response to the encoder knob.
추천
Seat Control Module
In seat-position modules, the MC9S12GC32MFAE drives the H-bridge motor controllers and reads Hall-position sensors through its 10-bit ADC. The HCS12's bit-handling instructions are well-suited to switch-debouncing and Hall-state machine decoding, which simplifies the seat-current watchdog code. LIN connectivity via the SCI port keeps the harness count low on the seat sub-network. The 48-LQFP package fits within the tight seat-module enclosure and uses standard reflow profiles.
추천
Lighting Control Module
The MC9S12GC32MFAE handles front and rear lighting control including adaptive headlamp leveling, daytime-running-light PWM, and turn-signal sequencing. The 8 PWM channels deliver high-resolution duty cycles for LED dimming without external constant-current driver modulation. CAN connectivity via SCI carries body-controller commands directly to the lighting ECU. Compared with discrete LED-driver ICs, the HCS12 retains firmware flexibility to add new lamp patterns over the program's lifecycle.
추천
LIN Slave Node
The MC9S12GC32MFAE can act as a LIN slave in distributed body-electronics networks, serving small modules such as window lifts, mirror adjusters, and rain-light sensors where full CAN is overkill. The on-chip SCI plus a LIN hardware assist deliver bus arbitration and frame-response timing well within the LIN 2.x specification. The 32 KB Flash comfortably holds LIN node capability plus the application-specific command table. The Vreg input range tolerates 12 V body-system transients after an external TVS clamp.
추천
Industrial Sensor Interface Module
The MC9S12GC32MFAE fits industrial 24 V I/O modules where 5 V regulated rails and CAN connectivity are needed for sensor aggregation. The HCS12 CPU is fast enough to handle 10 ms PLC scan-time tasks when reading field sensor inputs via the 10-bit ADC and serving them on CAN. The part's deterministic interrupt latency, characteristic of CISC HC12 cores, is well understood by industrial-control firmware engineers. The wide supply tolerance survives 24 V bus drop-outs during inductive load switching.
추천
추천 제품 요약
엔지니어링 참조 데이터: MC9S12GC32MFAE — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | MC9S12GC16MFAE | MC9S12GC32CFAE | MC9S12GC32VFAE |
|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 48-LQFP (7x7) | 48-LQFP (7x7) | 48-LQFP (7x7) | 48-LQFP (7x7) |
| Core | HCS12 (16-bit) | HCS12 (16-bit) | HCS12 (16-bit) | HCS12 (16-bit) |
| Flash | 32 KB | 16 KB (-50%) | 32 KB (same) | 32 KB (same) |
| RAM | 2 KB | 1 KB | 2 KB | 2 KB |
| EEPROM | 1 KB | 0.5 KB | 1 KB | 1 KB |
| Maximum Bus Clock | 25 MHz | 25 MHz | 25 MHz | 25 MHz |
| Supply Voltage | 2.97 V to 5.5 V | 2.97 V to 5.5 V | 2.97 V to 5.5 V | 2.97 V to 5.5 V |
주요 차별점
- 16-bit HCS12 core retains CodeWarrior/HCS12 toolchain investment (vs S32K (Cortex-M4))
- Integrated bandgap Vreg simplifies 5 V supply design (vs External LDO requirement of older HC11 parts)
- Cost-optimized 32 KB Flash at automotive grade (vs MC9S12DT128MPVE (128 KB))
설계 노트
Estimated: at 50 MHz core clock and typical HCS12 current draw of 30 mA from the internal Vreg, power dissipation on the 48-LQFP package at 5 V supply is roughly 0.15 W. The package's theta_JA of approximately 65 C/W on a 1 oz 4-layer board yields a junction rise near 10 C above ambient, well within the device's thermal envelope. Decoupling must include at least 0.1 uF X7R ceramic placed within 5 mm of every VDD pin pair.
Hold TEST low and BKGD high during reset release; an erroneously pulled TEST high on first power-up can lock the part in factory test mode and prevent normal vector fetch. Place a 4.7 kOhm pull-down on TEST and a 4.7 kOhm pull-up on BKGD. Also ensure VDDR is stable before VDD ramps to avoid Vreg latch-up - a Schottky clamp between VDD and VDDR is recommended if the upstream regulator has soft-start features.
Route the BKGD line on a top-layer microstrip with no vias and keep it at least 3W clear of switching nodes to preserve debug-port noise margin. Place the EXTAL/XTAL crystal within 5 mm of the MCU with guard-ring grounded traces on both sides, and route the XCLKS loop filter components on the same layer adjacent to pins 39-42. Add a small ferrite bead on VDDPLL supply if analog noise is observed on ADC channels.
규정 준수 정보
RoHS and lead-free compliance assumed from NXP LQFP-48 product family standards; AEC-Q100 status for this specific MPN is not explicitly confirmed in the verified data and is conservatively set to not_qualified.