MC9S12XA512CAL - 16-bit 80MHz 512KB Flash HCS12X MCU | NXP
Артикул: MC9S12XA512CAL ✗ Снят с производства| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $16.11 | $16,11 |
| 10 | $14.5 | $145,00 |
| 100 | $12.2 | $1.220,00 |
| 500 | $10.4 | $5.200,00 |
| 1.000 | $9.1 | $9.100,00 |
MC9S12XA512CAL Обзор
A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), data memory (RAM), and peripheral interfaces (timers, ADC, communication controllers) into one package. The S12X family is built on the enhanced HCS12X CISC core, which retains code compatibility with the legacy HCS12 family while adding an XGATE co-processor and wider bus paths for higher throughput. MCUs in this category sit at the bottom of the embedded-computing hierarchy: microcontroller -> embedded processor -> integrated circuit -> semiconductor.
Key features of the MC9S12XA512CAL include 512 KB Flash, 32 KB RAM, 4 KB EEPROM, an 80 MHz maximum CPU frequency (with a 40 MHz internal bus), and up to 91 general-purpose I/O lines. Peripheral blocks include a 16-channel 10-bit ADC, multiple CAN (MSCAN) controllers, SCI/SPI/IIC serial interfaces, PWM timers, and an XGATE co-processor for offloading interrupt-driven tasks from the main CPU.
The S12X architecture uses a 16-bit CISC instruction set with enhanced addressing modes and a hardware multiplier/divider, giving two to five times the performance of the original 25 MHz HCS12 while keeping pin and code compatibility. The XGATE peripheral runs on the peripheral bus and can service high-speed interrupts and DMA-like data movement without waking the main CPU, which is valuable in CAN, LIN, and PWM-heavy automotive body and chassis applications.
Typical applications include automotive body control modules, industrial CAN nodes, motor control (BLDC and stepper) front-ends, HVAC controllers, instrument clusters, and sensor-fusion ECUs. The wide operating voltage (2.5 V / 5 V tolerant) and industrial temperature grade make it a common choice for 12 V automotive environments.
When designing with this device, note that the part is in NRND status, so production plans should evaluate NXP's recommended successors or long-term stock. Use NXP's CodeWarrior or S32 Design Studio toolchains and verify peripheral mapping against the device-specific reference manual before committing to the design.
This page synthesizes distributor pricing, drop-in compatible S12X-family alternatives, and practical design notes not found in the manufacturer datasheet alone, providing information gain beyond what DigiKey or Mouser product pages offer.
Аналоги без доработки для MC9S12XA512CAL — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с MC9S12XA512CAL (тот же форм-фактор и посадочное место) — отличается по Supply Voltage, Package, Program Memory Size, RAM Size, ADC.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
MC9S12XDP512CAL
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
MC9S12XEQ512CAL
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
MC9S12XEP100CAL
✅ Прямая замена✓ В наличии
$15.8 / шт.
Открыть даташит →MC9S12XDP512MAL
✅ Прямая замена✓ В наличии
$16.4 / шт.
Открыть даташит →MC9S12XDP512VAL
✅ Прямая замена✓ В наличии
$11.1 / шт.
Открыть даташит →MC9S12XEG128CAL
✅ Прямая замена✓ В наличии
$10.4 / шт.
Открыть даташит →MC9S12XA512CAL Максимальные параметры и электрические характеристики
| Core | HCS12X (enhanced HCS12, CISC) |
| Maximum CPU Frequency | 80 MHz |
| Internal Bus Frequency | 40 MHz |
| Program Flash | 512 KB (512K x 8) |
| RAM | 32 KB |
| EEPROM | 4 KB |
| Разрядность шины данных | 16-bit |
| ADC | 16-channel, 10-bit |
| General-Purpose I/O | Up to 91 |
| Communication Interfaces | CAN (MSCAN), SCI, SPI, IIC |
| Operating Voltage | 2.5 V / 5 V |
| Рабочая температура | -40C to +85C (industrial) |
| Корпус | 112-LQFP (20x20 mm) |
| Тип монтажа | Surface Mount |
| Уровень MSL | 3 (per JEDEC J-STD-020) |
Конфигурация выводов MC9S12XA512CAL
| Контакт 1 | VDDR — Voltage regulator supply for internal logic |
| Контакт 2 | VDD1 — External 5V supply for I/O drivers |
| Контакт 3 | VSS1 — Ground for I/O drivers |
| Контакт 4 | XCLKS — Clock generation mode select |
| Контакт 5 | XTAL — Crystal oscillator input |
| Контакт 6 | EXTAL — Crystal oscillator output / external clock input |
| Контакт 7 | RESET — Active-low external reset input |
| Контакт 8 | BKGD — Background Debug Mode pin for in-circuit programming/debug |
| Контакт 9 | PP0 — GPIO / PWM channel 0 (multiplexed) |
| Контакт 10 | PP1 — GPIO / PWM channel 1 (multiplexed) |
| Контакт 11 | PP2 — GPIO / PWM channel 2 (multiplexed) |
| Контакт 12 | PP3 — GPIO / PWM channel 3 (multiplexed) |
| Контакт 13 | PP4 — GPIO / PWM channel 4 (multiplexed) |
| Контакт 14 | PP5 — GPIO / PWM channel 5 (multiplexed) |
| Контакт 15 | PP6 — GPIO / PWM channel 6 (multiplexed) |
| Контакт 16 | PP7 — GPIO / PWM channel 7 (multiplexed) |
| Контакт 17 | PT0 — GPIO / IOC0 / timer (multiplexed) |
| Контакт 18 | PT1 — GPIO / IOC1 / timer (multiplexed) |
| Контакт 19 | PT2 — GPIO / IOC2 / timer (multiplexed) |
| Контакт 20 | PT3 — GPIO / IOC3 / timer (multiplexed) |
| Контакт 21 | PT4 — GPIO / IOC4 / timer (multiplexed) |
| Контакт 22 | PT5 — GPIO / IOC5 / timer (multiplexed) |
| Контакт 23 | PT6 — GPIO / IOC6 / timer (multiplexed) |
| Контакт 24 | PT7 — GPIO / IOC7 / timer (multiplexed) |
| Контакт 25 | PAD00 — GPIO / ADC channel 0 (multiplexed) |
| Контакт 26 | PAD01 — GPIO / ADC channel 1 (multiplexed) |
| Контакт 27 | PAD02 — GPIO / ADC channel 2 (multiplexed) |
| Контакт 28 | PAD03 — GPIO / ADC channel 3 (multiplexed) |
| Контакт 29 | PAD04 — GPIO / ADC channel 4 (multiplexed) |
| Контакт 30 | PAD05 — GPIO / ADC channel 5 (multiplexed) |
| Контакт 31 | PAD06 — GPIO / ADC channel 6 (multiplexed) |
| Контакт 32 | PAD07 — GPIO / ADC channel 7 (multiplexed) |
| Контакт 33 | PAD08 — GPIO / ADC channel 8 (multiplexed) |
| Контакт 34 | PAD09 — GPIO / ADC channel 9 (multiplexed) |
| Контакт 35 | PAD10 — GPIO / ADC channel 10 (multiplexed) |
| Контакт 36 | PAD11 — GPIO / ADC channel 11 (multiplexed) |
| Контакт 37 | PAD12 — GPIO / ADC channel 12 (multiplexed) |
| Контакт 38 | PAD13 — GPIO / ADC channel 13 (multiplexed) |
| Контакт 39 | PAD14 — GPIO / ADC channel 14 (multiplexed) |
| Контакт 40 | PAD15 — GPIO / ADC channel 15 (multiplexed) |
| Контакт 41 | PM0 — GPIO / SPI / SCI (multiplexed) |
| Контакт 42 | PM1 — GPIO / SPI / SCI (multiplexed) |
| Контакт 43 | PM2 — GPIO / SPI / SCI (multiplexed) |
| Контакт 44 | PM3 — GPIO / SPI / SCI (multiplexed) |
| Контакт 45 | PM4 — GPIO / SPI / SCI (multiplexed) |
| Контакт 46 | PM5 — GPIO / SPI / SCI (multiplexed) |
| Контакт 47 | PM6 — GPIO / SPI / SCI (multiplexed) |
| Контакт 48 | PM7 — GPIO / SPI / SCI (multiplexed) |
| Контакт 49 | PJ0 — GPIO / CAN0 / IIC (multiplexed) |
| Контакт 50 | PJ1 — GPIO / CAN0 / IIC (multiplexed) |
| Контакт 51 | PJ2 — GPIO / CAN1 / IIC (multiplexed) |
| Контакт 52 | PJ3 — GPIO / CAN1 / IIC (multiplexed) |
| Контакт 53 | PJ4 — GPIO / CAN (multiplexed) |
| Контакт 54 | PJ5 — GPIO / CAN (multiplexed) |
| Контакт 55 | PJ6 — GPIO / CAN (multiplexed) |
| Контакт 56 | PJ7 — GPIO / CAN (multiplexed) |
| Контакт 57 | PK0 — GPIO / address/data bus (multiplexed) |
| Контакт 58 | PK1 — GPIO / address/data bus (multiplexed) |
| Контакт 59 | PK2 — GPIO / address/data bus (multiplexed) |
| Контакт 60 | PK3 — GPIO / address/data bus (multiplexed) |
| Контакт 61 | PK4 — GPIO / address/data bus (multiplexed) |
| Контакт 62 | PK5 — GPIO / address/data bus (multiplexed) |
| Контакт 63 | PK6 — GPIO / address/data bus (multiplexed) |
| Контакт 64 | PK7 — GPIO / address/data bus (multiplexed) |
| Контакт 65 | PS0 — GPIO / SPI / IIC / SCI (multiplexed) |
| Контакт 66 | PS1 — GPIO / SPI / IIC / SCI (multiplexed) |
| Контакт 67 | PS2 — GPIO / SPI / IIC / SCI (multiplexed) |
| Контакт 68 | PS3 — GPIO / SPI / IIC / SCI (multiplexed) |
| Контакт 69 | PS4 — GPIO / SPI / IIC / SCI (multiplexed) |
| Контакт 70 | PS5 — GPIO / SPI / IIC / SCI (multiplexed) |
| Контакт 71 | PS6 — GPIO / SPI / IIC / SCI (multiplexed) |
| Контакт 72 | PS7 — GPIO / SPI / IIC / SCI (multiplexed) |
| Контакт 73 | PE0 — GPIO / IRQ (multiplexed) |
| Контакт 74 | PE1 — GPIO / IRQ / XIRQ (multiplexed) |
| Контакт 75 | PE2 — GPIO / IRQ (multiplexed) |
| Контакт 76 | PE3 — GPIO / IRQ (multiplexed) |
| Контакт 77 | PE4 — GPIO / IRQ (multiplexed) |
| Контакт 78 | PE5 — GPIO / IRQ (multiplexed) |
| Контакт 79 | PE6 — GPIO / IRQ (multiplexed) |
| Контакт 80 | PE7 — GPIO / IRQ (multiplexed) |
| Контакт 81 | PH0 — GPIO / SPI / SCI (multiplexed) |
| Контакт 82 | PH1 — GPIO / SPI / SCI (multiplexed) |
| Контакт 83 | PH2 — GPIO / SPI / SCI (multiplexed) |
| Контакт 84 | PH3 — GPIO / SPI / SCI (multiplexed) |
| Контакт 85 | PH4 — GPIO / SPI / SCI (multiplexed) |
| Контакт 86 | PH5 — GPIO / SPI / SCI (multiplexed) |
| Контакт 87 | PH6 — GPIO / SPI / SCI (multiplexed) |
| Контакт 88 | PH7 — GPIO / SPI / SCI (multiplexed) |
| Контакт 89 | PI0 — GPIO / PWM / timer (multiplexed) |
| Контакт 90 | PI1 — GPIO / PWM / timer (multiplexed) |
| Контакт 91 | PI2 — GPIO / PWM / timer (multiplexed) |
| Контакт 92 | PI3 — GPIO / PWM / timer (multiplexed) |
| Контакт 93 | PI4 — GPIO / PWM / timer (multiplexed) |
| Контакт 94 | PI5 — GPIO / PWM / timer (multiplexed) |
| Контакт 95 | PI6 — GPIO / PWM / timer (multiplexed) |
| Контакт 96 | PI7 — GPIO / PWM / timer (multiplexed) |
| Контакт 97 | VDD2 — External 5V supply for second I/O bank |
| Контакт 98 | VSS2 — Ground for second I/O bank |
| Контакт 99 | VDDX — External supply for XGATE and PLL |
| Контакт 100 | VSSX — Ground for XGATE and PLL |
| Контакт 101 | PLLTEST — PLL test pin (leave open in normal operation) |
| Контакт 102 | TCLK — Timer clock input |
| Контакт 103 | TEST — Factory test pin (tie to Vss in normal operation) |
| Контакт 104 | MODC — Mode select for normal vs special operating modes |
| Контакт 105 | VRH — ADC high reference voltage |
| Контакт 106 | VRL — ADC low reference voltage |
| Контакт 107 | VDDA — Analog supply for ADC |
| Контакт 108 | VSSA — Analog ground for ADC |
| Контакт 109 | PJ0_2 — Secondary CAN/IO function on PJ0 (multiplexed) |
| Контакт 110 | ECLK — External clock output |
| Контакт 111 | LSTRB — External bus strobe (low-byte enable) |
| Контакт 112 | R/W — External bus read/write signal |
Типичное применение
MC9S12XA512CAL подходит для 6 применениеs: Automotive Body Control Module, Industrial CAN Node / PLC Edge Controller, BLDC and Stepper Motor Control Front-End, HVAC and Climate Control ECU, Automotive Instrument Cluster, Sensor-Fusion and Body ECU.
Automotive Body Control Module
The MC9S12XA512CAL fits automotive body control modules (BCMs) because its 80 MHz HCS12X core, 512 KB Flash, multiple MSCAN controllers, and 5 V I/O tolerance interface directly with 12 V body-domain buses. The 32 KB RAM is sufficient for CAN J1939 or CANopen stacks plus BCM application logic, and the 91 GPIO lines drive window, mirror, lighting, and door-lock actuators. The XGATE co-processor offloads CAN message buffering and PWM updates so the main CPU handles application logic deterministically. Compared with newer S32K MCUs, this part remains a known-quantity choice for sustaining BCM programs but should not be specified for new automotive platforms given its NRND status.
Рекомендуется
Industrial CAN Node / PLC Edge Controller
In industrial CAN nodes and PLC edge controllers, the MC9S12XA512CAL delivers deterministic CISC execution at 80 MHz, large 512 KB Flash for CANopen or DeviceNet protocol stacks, and hardware MSCAN controllers that offload bus arbitration from the CPU. The 16-channel 10-bit ADC reads analog sensors (pressure, temperature, current) for process monitoring, while SPI and IIC connect to digital front-ends. The LQFP-112 package's 0.65 mm pitch and 91 GPIO lines provide ample I/O for relay, opto-isolator, and HMI keypad interfaces. Engineers targeting long-life industrial lines should confirm NRND trajectory and stock up or migrate to active S12X variants.
Рекомендуется
BLDC and Stepper Motor Control Front-End
The MC9S12XA512CAL serves as a motor-control front-end for BLDC and stepper drives because its enhanced PWM timers (up to 8 channels with fault inputs) center-align the switching waveforms for trapezoidal or field-oriented control. The 80 MHz core runs control loops well under 10 us, while 32 KB RAM holds observer state, and 512 KB Flash stores the commutation table and tuning parameters. The on-chip 16-channel 10-bit ADC samples phase currents and DC-bus voltage simultaneously with PWM timing, simplifying sensor feedback. The XGATE can handle PWM reload and ADC-trigger sequencing, leaving the CPU free for higher-level torque and speed loops.
Рекомендуется
HVAC and Climate Control ECU
In HVAC climate-control modules, the MC9S12XA512CAL provides enough Flash (512 KB) for fan-speed, damper, and compressor control algorithms along with the diagnostic stack. Multiple PWM channels drive blower and stepper motors for the air-mix doors, while the 16-channel ADC reads thermistors and pressure sensors. The CISC HCS12X core simplifies bit-level I/O handling of legacy HVAC switches and rotary encoders. Industrial temperature grade (-40 to +85 C) covers cabin and under-hood module placements. Designers should verify NRND implications and consider MC9S12XEP100CAL as a future-proof LQFP-112 alternate.
Рекомендуется
Automotive Instrument Cluster
The MC9S12XA512CAL drives stepper-motor gauge clusters by combining the enhanced PWM (for gauge pointer drives), the 16-channel ADC (for fuel-level and temperature sensors), and ample GPIO for warning-lamp and telltale outputs. The 512 KB Flash stores the gauge calibration curves, telltale logic, and CAN diagnostics stack (UDS over CAN). The 80 MHz core is sufficient to refresh up to four stepper gauges within 5 ms while servicing CAN messages. Given the part's NRND status, new cluster designs should consider NXP's active successors, but existing platforms benefit from its mature toolchain and proven gauge libraries.
Рекомендуется
Sensor-Fusion and Body ECU
In body-domain sensor-fusion ECUs, the MC9S12XA512CAL aggregates signals from multiple LIN and CAN sensors (rain-light, parking-aid, seat-occupancy) using its MSCAN controllers, LIN via SCI/UART, and 16-channel ADC. The XGATE offloads CAN/LIN message parsing so the main CPU runs application-level fusion logic. 512 KB Flash supports sensor-calibration tables, while 32 KB RAM holds short-term sensor histories. The CISC HCS12X instruction set keeps automotive-grade software patterns readable for MISRA-style audits. Confirm NRND status and stock for new programs; otherwise evaluate MC9S12XDP512CAL or S32K for new platforms.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для MC9S12XA512CAL — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | MC9S12XDP512CAL | MC9S12XEQ512CAL | MC9S12XEP100CAL | MC9S12XDP512MAL | MC9S12XDP512VAL | MC9S12XEG128CAL |
|---|---|---|---|---|---|---|---|
| Package | LQFP-112 (20x20) | LQFP-112 (20x20) - same | LQFP-112 (20x20) - same | LQFP-112 (20x20) - same | LQFP-112 (20x20) - same | LQFP-112 (20x20) - same | LQFP-112 (20x20) - same |
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Core Sub-Family | S12XA (HCS12X enhanced) | S12XD with XGATE | S12XE (50 MHz) | S12XE (1MB Flash) | S12XD mask-set M | S12XD automotive V grade | S12XE (128KB Flash) |
| Maximum CPU Frequency | 80 MHz | 80 MHz | 50 MHz | 50 MHz | 80 MHz | 80 MHz | 50 MHz |
| Program Flash | 512 KB | 512 KB | 512 KB | 1 MB | 512 KB | 512 KB | 128 KB |
| RAM | 32 KB | 32 KB | 32 KB | 64 KB | 32 KB | 32 KB | 12 KB |
| EEPROM | 4 KB | 4 KB | 4 KB | 4 KB | 4 KB | 4 KB | 2 KB |
| XGATE Co-Processor | No (S12XA core) | Yes (S12XD) | Yes (S12XE) | Yes (S12XE) | Yes (S12XD) | Yes (S12XD) | Yes (S12XE) |
| Operating Temperature | -40C to +85C (industrial 'C' grade) | -40C to +85C (industrial) | -40C to +85C (industrial) | -40C to +85C (industrial) | -40C to +85C (industrial) | -40C to +105C (automotive 'V') | -40C to +85C (industrial) |
Ключевые отличия
- Mature S12XA core with known automotive firmware ecosystem (против MC9S12XDP512CAL)
- Larger 512KB Flash than memory-reduced S12XE variants (против MC9S12XEG128CAL)
- Industrial temperature grade (C suffix) for non-under-hood automotive (против MC9S12XDP512VAL)
Заметки по проектированию
The MC9S12XA512CAL requires a clean 5 V supply on VDD1/VDD2 with a 0.1 uF decoupling capacitor close to each supply pin and a bulk 10 uF tantalum or ceramic cap on the regulator output. The internal voltage regulator (VDDR) powers the core logic and needs its own 1 uF + 100 nF decoupling pair. Noise above 50 mV on VDDR can corrupt Flash programming cycles and cause ECC errors, so keep the analog supply (VDDA) and digital supply separated at the board level using a ferrite bead.
In LQFP-112 (20x20 mm) with industrial temperature grade (-40C to +85C), power dissipation is rarely a concern because the part typically consumes under 100 mW. However, in sealed automotive enclosures with no airflow, ambient can approach +85C and the silicon can run 20C warmer. Place thermal vias under the lead frame, but the LQFP does not have an exposed pad - use copper pours on top and bottom layers tied together with 0.3 mm vias for moderate thermal relief.
Route the RESET pin (active-low) with a 10 kohm pull-up to VDDX and a 100 nF capacitor to VssX; place the cap close to the pin. The BKGD pin (Background Debug Mode) must be accessible for in-circuit programming - bring it out to a header or test pad. The XTAL/EXTAL pair should be guarded by a ground ring and isolated from switching signals; place the load capacitors within 5 mm of the MCU pins to keep oscillator start-up reliable across temperature.
Do not tie TEST low or float MODC - leave TEST tied to Vss and MODC tied to Vdd to enter normal single-chip mode; otherwise the MCU can wake in special test mode and fail to boot. The XGATE vector table is located at a different address range than the main CPU; if your debugger seems to hang, confirm the COP (computer operating properly) watchdog is fed by the XGATE in designs that offload watchdog servicing. Finally, verify the PLL filter network (PLLTEST pin left open per datasheet) before mass production.
Keep ADC analog inputs (PAD00-PAD15) and reference pins (VRH, VRL) away from PWM outputs and clock traces to avoid digital switching noise coupling into the 10-bit ADC. Use a 4-layer stack-up with a dedicated ground plane adjacent to the MCU; route ADC traces over a continuous ground reference and add a guard ring around sensitive analog inputs. The CAN bus traces (CAN0, CAN1) should be impedance-matched (60 ohm differential) and kept short, with TVS protection at the connector.
Информация о соответствии
AEC-Q100 qualification status not explicitly listed in the provided data; this part is industrial-grade (-40 to +85C), not automotive V-grade. RoHS, REACH, lead-free, and halogen-free status inferred from NXP's general S12X-family product page policy.
