Mga Produkto (46,000+)

LM2904DR2G - Dual 3-32V Op Amp, 8-SOIC | onsemi
LM2904DR2G

LM2904DR2G - Dual 3-32V Op Amp, 8-SOIC | onsemi

onsemi LM2904DR2G is a dual general-purpose operational amplifier with two independent amplifier channels, a 3 V to 32 V supply-voltage range, and an 8-SOIC surface-mount package. The device supports single-supply or split-supply operation, and its common-mode input range extends to ground or VEE, making it suitable for systems using low positive supply voltages. An operational amplifier is an analog signal-processing IC that amplifies the voltage difference between its inverting and non-inverting inputs. The LM2904 belongs to the dual operational amplifier family within the broader operational amplifier, analog IC, and semiconductor hierarchies. Its two channels can amplify two signals independently, or one channel can be used as a buffer while the other performs amplification, filtering, or comparison. The principal advantages include low power drain, common-mode input operation extending to ground or VEE, and flexible single- or dual-supply configurations. The 3 V minimum supply supports modern low-voltage systems, while the 32 V maximum accommodates higher industrial rails. The -40°C to +105°C operating-temperature range supports applications across consumer, instrumentation, industrial-control, and power-management equipment. The LM2904 uses a bipolar operational-amplifier architecture. Each channel includes differential inputs and an output stage designed for general-purpose signal conditioning. Unlike rail-to-rail-input devices, its useful input range depends on the selected supply arrangement and common-mode limits. Designers should therefore verify signal levels against the operating conditions in the manufacturer datasheet rather than assuming full rail-to-rail input capability. Typical applications include low-side current monitoring, sensor-signal conditioning, active filtering, buffer stages, audio preamplification, threshold detection, and general industrial control. It is especially useful when a design requires operation from a single positive supply while processing signals that approach the negative supply rail, which is represented by ground in a single-supply circuit. For reliable implementation, place the input, feedback, and decoupling components close to their associated pins, use a stable low-noise power source, and check output-current and common-mode limits over the complete temperature range. Bypass capacitors should connect directly to the supply pins to minimize parasitic inductance and preserve stability. This product page combines the operating characteristics, pin assignments, application guidance, drop-in comparison, and practical layout considerations needed to evaluate the LM2904DR2G for a new analog signal chain.

RFQ Kontak
LM2904DR2GH - Dual 1MHz Op Amp, 3-32V Supply, SOIC-8 | onsemi
LM2904DR2GH

LM2904DR2GH - Dual 1MHz Op Amp, 3-32V Supply, SOIC-8 | onsemi

The onsemi LM2904DR2GH is a dual general-purpose operational amplifier with two independent amplifier channels in an 8-pin SOIC (D) package. It offers a gain-bandwidth product of 1 MHz, single-supply operation from 3.0 V to 32 V, and a common-mode input range that extends to the negative supply rail, making it a drop-in choice for legacy and new analog signal-chain designs. An operational amplifier is a high-gain differential amplifier whose inverting and non-inverting inputs are compared, producing an output that drives the difference between them. The dual-amplifier form factor halves board area for common tasks such as buffer and gain stages, level shifting, active filters, transducers, and sensor conditioning. In the power-management hierarchy, op amps sit alongside regulators and references as fundamental analog building blocks, and the LM2904 family is one of the most widely cloned dual general-purpose amplifier families in the industry. Key features of the LM2904DR2GH include short-circuit-protected outputs, a true differential input stage, internally compensated operation (no external compensation network required), low input bias currents, and ESD clamps on the inputs that improve ruggedness without degrading signal integrity. Because the amplifier is internally compensated, it is stable with unity-gain noise gain, which simplifies feedback design in buffer and general-purpose configurations. The common-mode input range extending to the negative supply is the defining architectural advantage in single-supply systems. The input stage can operate with signals referenced near 0 V while the device runs from a single positive rail, removing the need for a negative bias supply or an artificial ground in sensor, audio, and industrial instrumentation circuits. Internally, the part combines a differential input pair with a class-A/AB output stage that delivers rail-to-rail output swing close to the supply limits at light to moderate loads. Typical applications include low-side current sensing with shunt amplifiers, audio preamplifier and mixer stages, active filters for sensor signals, comparators and threshold detectors, bridge and strain-gauge instrumentation, relay and solenoid drive feedback, and general industrial control signal conditioning. The wide 32 V supply ceiling also suits 24 V industrial bus rails that need headroom for transients. One key design consideration is that the 1 MHz gain-bandwidth product limits closed-loop bandwidth to roughly the gain-bandwidth divided by the noise gain. Use a current-feedback or faster rail-to-rail device when the signal bandwidth exceeds roughly 100 kHz at higher closed-loop gains, and keep layout short to avoid parasitic capacitance on the inverting input that can destabilize the amplifier. This page consolidates manufacturer feature data, pin-level detail, drop-in replacement options, and practical layout guidance so that engineers can qualify the LM2904DR2GH for both new designs and repair or obsolescence-driven redesigns.

RFQ Kontak
LM2904DRE4 - Dual 700kHz Op Amp | Texas Instruments
LM2904DRE4

LM2904DRE4 - Dual 700kHz Op Amp | Texas Instruments

Texas Instruments LM2904DRE4 is a dual, general-purpose operational amplifier in an 8-pin SOIC package. It operates from a single power supply or from split supplies, supports supply voltages up to 26 V, and provides a gain-bandwidth product of 700 kHz. The device contains two independent operational-amplifier channels and is intended for cost-sensitive applications that require an industry-standard, widely available amplifier. An operational amplifier is an analog signal-conditioning integrated circuit whose differential input and high open-loop gain allow it to amplify, buffer, filter, compare, or drive external circuits. The LM2904 belongs to the operational-amplifier hierarchy within amplifier ICs and power-semiconductor devices. Its two channels can amplify different signals in one package while sharing common supply pins, making it useful where board area and external component count are important. The 700 kHz gain-bandwidth product is the principal dynamic parameter identified for the LM2904 family. It determines the useful bandwidth for closed-loop amplifier configurations and affects how quickly the output can respond to input-voltage changes. The manufacturer lists a slew rate of 0.3 V/us for the LM2904DRE4, another indication that the device is optimized for general-purpose analog signal processing rather than high-speed data acquisition. The LM2904DRE4 is specified for operation with a maximum total supply voltage of 26 V. This allows use in conventional 5 V, 12 V, and 24 V industrial systems when the absolute maximum voltage and common-mode operating limits are respected. Its supply-current drain is characterized as low and independent of supply voltage, while the common-mode input range includes ground, which is important in single-supply sensor and control circuits. Typical applications include low-cost sensor conditioning, audio preamplification, general-purpose filtering, comparators with suitable output pull-up arrangements, and two-channel industrial control. The dual-channel format is especially useful for portable instruments, sensor interfaces, audio boards, and educational electronics where one package provides two independent amplifier sections. Design with the LM2904DRE4 using the pin-description table and recommended operating conditions in the manufacturer datasheet. Pay particular attention to input common-mode voltage, output swing, supply polarity, input bias current, and stability requirements. Decoupling capacitors should be placed close to the supply pins, and sensitive analog inputs should be routed away from switching nodes and high-current return paths. This product page combines the manufacturer’s core electrical ratings with practical application guidance, package information, and a same-package replacement comparison. It also distinguishes the standard dual LM2904 ordering options from automotive, revised, and cross-brand equivalents, helping engineers assess footprint compatibility before committing to a PCB substitution.

RFQ Kontak
LM2904DRG3 - Dual 26 V, 700 kHz Op Amp | Texas Instruments
LM2904DRG3

LM2904DRG3 - Dual 26 V, 700 kHz Op Amp | Texas Instruments

Texas Instruments LM2904DRG3 is a dual, general-purpose operational amplifier with two independent amplifiers, a 26 V supply rating, a 700 kHz gain-bandwidth product, and an 8-pin SOIC package. The device supports single-supply or split-supply operation and is intended for general-purpose signal conditioning where a wide operating-voltage range and conventional micropower consumption are useful. An operational amplifier is a voltage-feedback amplifier that uses high open-loop gain to amplify the difference between its inverting and non-inverting inputs. Operational-amplifier ICs sit within the broader amplifier hierarchy and are widely used in analog signal chains for sensing, buffering, filtering, comparison, and closed-loop control. The LM2904 contains two frequency-compensated amplifiers, allowing one package to serve two independent analog functions. The LM2904 provides a 700 kHz gain-bandwidth product, 0.3 V/us typical slew rate, and approximately 0.7 mA typical supply-current drain. Its common-mode input range includes ground, which makes it useful in single-supply applications that process signals near the lower supply rail. The 26 V maximum supply rating provides additional operating headroom for industrial and automotive-style circuits when the board is otherwise designed for lower voltages. Each amplifier is frequency compensated and intended for general-purpose closed-loop operation. Its approximately 700 kHz gain-bandwidth product supports signal paths that do not require the bandwidth of modern precision or high-speed amplifier families. The dual configuration can implement two amplifiers per package, reducing board area in designs such as sensor conditioning, active filtering, error amplifiers, and low-frequency control loops. The 8-SOIC package is also a practical option for through-hole assembly processes. Typical applications include low-frequency sensor signal conditioning, active filters, audio preamplifier stages, battery-powered instrumentation, and industrial control interfaces. In a typical application, the amplifier is configured with external feedback resistors or capacitors, while the non-inverting input receives the sensor or reference signal. Single-supply operation is especially useful when the input signal remains close to ground and a negative supply is undesirable. Designers should verify the input and output common-mode limits across the intended supply voltage and load current, and should use suitable bypassing capacitors near the power pins. Stable operation also depends on following the recommended feedback-network values and ensuring the source and load impedances do not compromise gain, noise, or phase margin. The 8-SOIC footprint leaves adequate routing space for conventional external compensation or gain-setting components where needed. This page combines the manufacturer product information with practical package, sourcing, replacement, and design guidance. It highlights the LM2904DRG3's useful balance of dual-channel integration, wide supply range, conventional bandwidth, and assembly compatibility for cost-conscious general-purpose analog designs.

RFQ Kontak
LM2904DRG4 - Dual 26V 700kHz Op Amp | Texas Instruments
LM2904DRG4

LM2904DRG4 - Dual 26V 700kHz Op Amp | Texas Instruments

Texas Instruments LM2904DRG4 is a dual, general-purpose operational amplifier with a 26 V supply rating, 700 kHz gain-bandwidth product, and 8-pin SOIC package. The device contains two independent, internally frequency-compensated amplifiers intended for cost-sensitive systems that require reliable operation from single or dual supplies. Its 8-SOIC package is supplied tape-and-reel under the DRG4 ordering suffix. An operational amplifier is an analog signal-processing IC that compares voltages applied to its high-impedance differential inputs and drives its output to amplify the difference between them. Within the broader semiconductor hierarchy, an operational amplifier belongs to the amplifier IC and linear IC categories. The LM2904 combines two amplifiers in one package, allowing a circuit to implement two signal-processing channels without using two separate single-amplifier packages. The LM2904 provides 700 kHz gain bandwidth and a typical slew rate of 0.3 V/µs. Its single-supply current drain is approximately 0.7 mA per amplifier and is described as independent of supply voltage. The common-mode input range includes ground, while the device supports high-voltage operation for industrial, automotive, and control-system applications. These characteristics make it appropriate for general signal conditioning, feedback control, buffering, and low-to-moderate-frequency analog systems. Each amplifier is independent and internally frequency compensated, simplifying circuit design because an external compensation network is not required for ordinary closed-loop operation. The wide supply capability also allows operation from a single supply or from positive and negative rails. Designers should still verify common-mode range, output swing, input bias behavior, and stability against the specific supply voltage used in the final application. Typical uses include industrial process-control loops, transducer-signal conditioning, audio and communications-channel amplification, sensor interfaces, and low-frequency feedback systems. In a control application, the amplifier can close a feedback loop around an actuator or sensor stage. In signal conditioning, it can amplify a sensor voltage while preserving the common-mode range permitted by the selected power rails. A key design consideration is that the 8-SOIC footprint requires conventional surface-mount assembly and careful handling of input bias current and common-mode limits. Decoupling capacitors should be placed close to the supply pins, and sensitive input traces should be kept away from switching nodes. Input and output voltages must remain within the limits stated in the manufacturer datasheet. This page organizes the verified device information, sourcing routes, and engineering considerations into a practical component-selection reference. It also identifies any missing electrical details explicitly so engineers can consult the pin-description and electrical-characteristics tables before releasing a design.

RFQ Kontak
LM2904DT - Dual 1.1MHz General Purpose Op Amp | STMicroelectronics | SOIC-8
LM2904DT

LM2904DT - Dual 1.1MHz General Purpose Op Amp | STMicroelectronics | SOIC-8

The STMicroelectronics LM2904DT is a low-power dual general-purpose operational amplifier providing two independent, internally frequency-compensated amplifiers in an 8-pin SOIC (SOP-8) surface-mount package, with a 1.1 MHz unity-gain bandwidth and single-supply operation for automotive and industrial control systems. An operational amplifier (op amp) is a high-gain differential amplifier that compares an inverting and a non-inverting input and drives its output to amplify the difference between them. When the frequency compensation network is integrated on-chip, the part is called internally compensated and is stable at unity gain without external components. The dual configuration places two independent amplifiers in a single 8-SOIC body, roughly halving the footprint compared with two discrete single amplifiers. In the product hierarchy the device sits as an operational amplifier within analog amplifier ICs and, in turn, within integrated circuits. Key features include two independent channels in one 8-SOIC package, a 1.1 MHz gain-bandwidth product, internal frequency compensation that removes external compensation parts, a low power supply drain that is independent of the magnitude of the output voltage swing, and single-supply operation over a wide voltage range. The LM2904 family was designed specifically for automotive and industrial control systems, so robustness and supply-voltage tolerance matter more than precision offset or ultra-low noise. Internally the device uses a classic internally compensated bipolar input stage with single-ended outputs. Both amplifiers share one supply rail and one ground reference, so bypass and grounding rules apply to the whole package: place a small ceramic capacitor adjacent to the supply pin and add local bulk decoupling near the pins. Output swing is not rail-to-rail, so the load must be chosen so the output stays inside the supply range, and the input common-mode range must be respected when signals approach the rails. Typical uses include motor and solenoid feedback loops in automotive electronic control units, industrial sensor signal conditioning, bridge and transducer amplification, low-side current sensing, and general DC buffering inside PLC and instrumentation racks. Two independent channels in one package also serve a control loop and a monitoring channel together. One design tip: keep feedback routing short, guard high-impedance input nodes against pickup, and decouple the supply at the package. Do not select this amplifier where rail-to-rail input or output, very low noise, or micro-power operation is required; choose a precision or CMOS-input amplifier family instead. This page combines the manufacturer specification summary, a complete pin map for the SOIC-8 footprint, drop-in alternatives with quantified parameter differences, and practical power, layout, and signal-integrity notes that are not combined in a single manufacturer document.

RFQ Kontak
LM2904EDR2G - Dual Low-Power Operational Amplifier | onsemi
LM2904EDR2G

LM2904EDR2G - Dual Low-Power Operational Amplifier | onsemi

onsemi LM2904EDR2G is a dual, general-purpose operational amplifier with 2 amplifier channels in an 8-pin SOIC package. It is designed for low power drain, common-mode input operation extending toward ground or VEE, and use with either a single supply or split supplies. These characteristics make it suitable for battery-operated instrumentation, sensor signal conditioning, audio and communication circuits, and general analog control systems where two independent amplifier sections are required. An operational amplifier is an analog integrated circuit that uses high-gain differential amplification with negative feedback to create stable, controlled gain. The dual-amplifier configuration combines two amplifier sections in one package, reducing board area compared with two separate single amplifiers. Its common-mode input range extending toward ground or VEE is particularly useful in single-supply systems, where signals may be referenced close to the lower supply rail. The LM2904EDR2G is positioned as a low-power, general-purpose amplifier rather than a high-speed or precision device. Its dual-channel architecture supports independent signal paths within one package, while single-supply or split-supply operation allows integration into both grounded and bipolar-style signal chains. The 8-SOIC package provides a familiar surface-mount footprint suitable for conventional PCB assembly. The LM2904 family derives its circuit design from the same basic architecture used in quad operational amplifiers, with the LM2904 providing two amplifier sections. This family positioning supports familiar design conventions and makes the device relevant to applications previously addressed by discrete or multi-package amplifier arrangements. Exact input offset, bandwidth, current, noise, and voltage-limit figures should be confirmed against the manufacturer datasheet for the selected operating condition. Typical applications include DC sensor amplification, low-side current sensing, audio preamplification, industrial signal conditioning, temperature-measurement circuits, and portable equipment powered from a single battery. In each case, the dual section can process two related or independent channels while operating close to the lower supply rail. Decoupling and grounding remain important because they directly affect stability and measured signal quality. For PCB implementation, place the device power pins and input and output traces according to the manufacturer pin-description table. Use a stable reference ground, route sensitive input lines away from switching nodes, and provide local supply bypassing to limit disturbance reaching the amplifier. Verify the final circuit against minimum gain, output swing, slew rate, and common-mode limits before production. This product page combines the exact ordering information with practical guidance for dual-amplifier selection, pinout use, power-rail planning, and replacement assessment. It also identifies compatible circuit roles and highlights where engineers must verify operating limits rather than assume that every low-power dual amplifier is interchangeable.

RFQ Kontak
LM2904F-E2 - Dual Ground-Sense Op Amp, 3-32V | ROHM Semiconductor
LM2904F-E2

LM2904F-E2 - Dual Ground-Sense Op Amp, 3-32V | ROHM Semiconductor

The ROHM Semiconductor LM2904F-E2 is a dual ground-sense operational amplifier designed for single-supply operation from 3V to 32V. The device is specified in an 8-pin SOP package and is intended for general-purpose amplifier applications requiring low current consumption, wide operating supply voltage, and input/output common-mode range extending toward ground. The LM2904F-E2 is identified by ROHM as a ground-sense operational amplifier and is not recommended for new designs. A ground-sense operational amplifier is an op-amp configuration designed to measure or amplify small voltage signals referenced to ground, especially signals whose lower operating range is close to 0V. The LM2904 family combines two amplifiers in one package, allowing each channel to be used independently for signal conditioning, buffering, or low-level voltage amplification. Its wide supply-voltage range allows operation from 3V single-supply systems through higher-voltage industrial control and instrumentation circuits. The verified product information identifies the LM2904F-E2 as a standard general-purpose amplifier with two circuits, an 8-SOP package, and a 3V to 32V operating supply range. ROHM's product page also identifies the device as a ground-sense operational amplifier and states that it cannot be used for new designs. The -E2 suffix denotes the manufacturer's ordering or packaging designation, while the F variant identifies the ground-sense amplifier family. Typical uses include current-sense signal conditioning, sensor-interface circuits, low-voltage control systems, and instrumentation in which the input signal can approach the negative supply rail. The dual configuration can reduce board area when two related analog channels are required. The 8-pin SOP package is also compatible with conventional through-hole and leaded assembly processes, although current designs should confirm the availability and lifecycle status of the exact suffix before committing a new production release. Designers should review the manufacturer datasheet for the complete electrical limits, input common-mode behavior, output swing, bias-current specifications, noise values, compensation stability, and recommended decoupling. A stable bypass capacitor should be placed close to the supply pins, and unused input channels should be handled according to the datasheet's recommended configuration. Because the manufacturer does not recommend this part for new designs, engineers should normally evaluate a current recommended dual operational amplifier with the same 8-pin footprint and equivalent electrical performance. This page combines the manufacturer product information, distributor identification, lifecycle notice, package data, and practical engineering guidance for engineers evaluating the LM2904F-E2 or searching for a compatible replacement.

RFQ Kontak
LM2904FJ-E2 - Dual Ground-Sense Op Amp | ROHM | Sensors
LM2904FJ-E2

LM2904FJ-E2 - Dual Ground-Sense Op Amp | ROHM | Sensors

The ROHM Semiconductor LM2904FJ-E2 is a dual ground-sense operational amplifier with two amplifier circuits, a single-supply operating range of 3 V to 32 V, and low current consumption in an 8-SOP-J package. Its input and output ground-sense architecture allows the device to operate near the lower supply rail when the system requires common-mode input and output behavior close to ground. A ground-sense operational amplifier is a voltage-feedback amplifier designed for applications where the signal and output can operate near the negative supply rail. Within the broader hierarchy, the LM2904FJ-E2 is an operational amplifier, an analog amplifier IC, and a member of the power-management and signal-conditioning component category. The dual configuration provides two independent amplifier channels in one package, reducing board area in instrumentation and sensor-interface circuits that require more than one amplification stage. The principal device characteristics are its dual-circuit configuration, 3 V to 32 V single-supply range, low current consumption, and input/output ground-sense operation. The 8-SOP-J construction supports conventional surface-mount assembly. Unlike precision, low-noise amplifier families optimized for very small signals, this device is positioned as a general-purpose ground-sense amplifier for cost-conscious industrial and instrumentation designs. The LM2904FJ-E2 can be placed in non-inverting or inverting signal-conditioning configurations, subject to the stability, input-range, and output-swing limitations described by the manufacturer datasheet. Its broad supply range permits operation from low-voltage systems or from a 24 V industrial rail when the relevant device and package ratings permit. The dual architecture is useful when a design needs paired gain stages, buffering, or independent channels. Typical applications include current-sense amplifier interfaces, low-side sensor conditioning, industrial control modules, battery-powered instrumentation, and measurement systems referenced near ground. In each case, the ground-sense characteristic can reduce output-swing constraints that would otherwise limit a conventional amplifier at low signal levels. The exact input and output ranges should be checked against the operating voltage before finalizing the signal chain. PCB design should preserve the manufacturer's recommended bypass capacitance and account for the common-mode and output-swing limits of the selected operating point. Input and output routing should be short, with the ground reference returned cleanly to the device ground pin. Breadboard or long-trace layouts can introduce coupling and stability problems that do not appear in compact, well-decoupled production layouts. This page combines the confirmed device identity, electrical characteristics, package information, application guidance, sourcing workflow, and engineering checks for LM2904FJ-E2. It is intended to help engineers determine whether the dual ground-sense topology fits a specific PCB before ordering, while clearly separating confirmed specifications from values that must be confirmed in the manufacturer datasheet.

RFQ Kontak
LM2904FV-E2 - Dual Ground-Sense Op Amp, 3-32V | ROHM
LM2904FV-E2

LM2904FV-E2 - Dual Ground-Sense Op Amp, 3-32V | ROHM

ROHM LM2904FV-E2 is a dual ground-sense operational amplifier designed for low-current consumption and single-supply operation over a 3 V to 32 V range. The device contains two amplifier channels in an 8-pin SSOP-B package and supports input/output common-mode operation close to ground. These characteristics make it suitable for low-side current sensing, battery monitoring, portable instrumentation, and control systems where the measured signal is referenced to ground. A ground-sense operational amplifier is an analog amplifier optimized for signals near the supply-ground rail. In the broader semiconductor hierarchy, an operational amplifier is a linear amplifier IC used to amplify voltage differences, and a ground-sense amplifier adds input and output common-mode characteristics suited to low-side sensing. It can therefore process small signals without requiring a negative supply rail when the input and output remain within the specified common-mode range. The LM2904FV-E2 provides two independent amplifier channels, low current consumption, and a wide operating supply range. Its ground-sense architecture supports signal acquisition in circuits where one input is close to 0 V and the other input represents a small voltage change. The 8-pin SSOP-B format also provides a compact surface-mount option for industrial and consumer control equipment. ROHM identifies the LM2904FV family as not recommended for new designs, so the device is primarily appropriate for maintenance, repair, and continuation of an established design. Internally, the dual amplifier combines two standard operational-amplifier channels with ground-sense capability and a common supply architecture. The two channels can amplify related measurements, such as two halves of a differential signal, or operate independently when each channel has its own feedback network. The wide 3 V to 32 V supply span permits use from low-voltage battery-powered systems through industrial control rails without requiring a separate low-voltage regulator for the amplifier itself. Typical uses include low-side shunt-current measurement, battery-voltage monitoring, sensor-interface circuits, industrial process controls, and portable test equipment. In a low-side current-sense design, the shunt produces a small voltage proportional to current; the amplifier boosts that differential signal while its ground-sense behavior supports operation near the lower rail. The dual configuration can also provide signal conditioning for paired sensors or implement two independent gain stages. Designers should verify the exact input and output common-mode limits, output-current capability, input-bias current, offset voltage, and noise specifications against the manufacturer datasheet before fixing gain or bias networks. Input bias-current error can be significant when sensing very low-resistance shunts, so resistor values should be selected to balance bias error against bandwidth and stability. Decoupling capacitors should be placed close to the supply pins, and the unused channel should be configured according to the datasheet rather than left floating. This product page combines the manufacturer lifecycle status with package, voltage, and application information, while also providing procurement guidance, comparison structure, and practical engineering notes. Those additions help engineers evaluate whether the established LM2904FV-E2 fits a legacy or maintenance design and what electrical and PCB checks are required before substitution.

RFQ Kontak
LM2904FVJ-E2 - Dual 3-32V Ground-Sense Op Amp | ROHM
LM2904FVJ-E2

LM2904FVJ-E2 - Dual 3-32V Ground-Sense Op Amp | ROHM

The ROHM Semiconductor LM2904FVJ-E2 is a dual ground-sense operational amplifier designed for two independent amplifier channels, a 3 V to 32 V single-supply operating range, and an 8-pin TSSOP-BJ package. Its input and output common-mode range extends to ground, making it suitable for low-side sensing and signal-conditioning systems whose signals remain close to the negative supply rail. A ground-sense operational amplifier is a voltage-feedback amplifier intended to amplify or buffer signals near 0 V without requiring a dual supply. The LM2904FVJ belongs to the broader operational-amplifier hierarchy: voltage-feedback amplifier, analog signal-conditioning IC, and semiconductor. Its rail-to-rail input-and-output ground-sense capability is especially useful in battery-powered monitoring, industrial sensing, and portable equipment where the signal may approach the lower supply limit. The device provides two amplifier channels in one package, reducing board area compared with two separate single amplifiers. Its wide 3 V to 32 V operating range accommodates low-voltage systems as well as higher-voltage industrial supplies. The manufacturer describes low current consumption and ground-sense operation as principal characteristics. Because both channels share one package, designers must also evaluate common supply impedance, thermal behavior, output-current sharing between independent loads, and the maximum load conditions of each amplifier. The LM2904FVJ-E2 is categorized as a standard general-purpose amplifier, but its ground-sense architecture is important in applications where the measured voltage can approach 0 V. Unlike a conventional rail-to-rail amplifier selected only by input common-mode limits, this device specifically addresses ground-referenced input and output operation. The TSSOP-BJ package offers a compact surface-mount format, although careful pin placement and decoupling remain necessary to minimize noise and ground-offset errors. Typical uses include low-side current detection, battery monitoring, portable instrumentation, industrial transducers, sensor interfaces, and low-voltage control systems. In a current-sense application, the amplifier can sit on the low side of a shunt, preserving a ground-centered measurement signal while reducing the voltage burden imposed on the measured circuit. In sensor systems, the close-to-ground input capability reduces the need for an additional offsetting supply. Design around the manufacturer pinout and place input, output, and decoupling connections to minimize parasitic resistance in the feedback network. Maintain short ground-return paths and decouple the supply close to the device. Because the manufacturer classifies this product as not recommended for new designs, new production projects should normally use a currently recommended amplifier unless the legacy footprint, supply range, ground-sense behavior, and electrical performance are mandatory. This page combines the exact manufacturer lifecycle position, package and supply information, drop-in alternatives, application guidance, and design cautions for engineers maintaining or replicating an existing LM2904FVJ-E2-based design. It emphasizes practical selection limits rather than treating the legacy part as a universal modern replacement.

RFQ Kontak
LM2904FVM-GTR - Dual Ground-Sense Op Amp | ROHM
LM2904FVM-GTR

LM2904FVM-GTR - Dual Ground-Sense Op Amp | ROHM

The ROHM Semiconductor LM2904FVM-GTR is a dual ground-sense operational amplifier designed for general-purpose signal conditioning. It provides two amplifier channels in an 8-MSOP surface-mount package, operates from a single supply of 3 V to 32 V, and combines a wide input-voltage range with low current consumption. The -GTR ordering code identifies tape-and-reel production handling. An operational amplifier is an analog amplifier IC that uses feedback to amplify the difference between two input voltages. The dual configuration integrates two amplifier channels into one package, reducing board area in designs that need more than one amplification stage. Within the broader semiconductor hierarchy, an operational amplifier belongs to the amplifier IC and linear IC families, where it supports precision control, measurement, buffering, and signal-conditioning functions. The ground-sense architecture is suited to circuits that monitor or condition signals referenced toward ground. The two independent channels can be used separately or together in applications such as current-sense amplifiers, low-side sensing, sensor interfaces, and general feedback-control blocks. The 3 V to 32 V single-supply range permits operation from compact 3 V systems through substantially higher industrial supply rails, provided the complete circuit remains within the device operating limits. Low current consumption makes the LM2904FVM useful in designs where the amplifier must coexist with battery-powered, portable, or broadly distributed sensing circuitry. Its MSOP-8 package supports compact surface-mount assembly, while the dual channel count reduces the number of packages needed compared with two single operational amplifiers. Engineers should still verify output-current demand, input common-mode range, output swing, noise, offset, and stability requirements against the manufacturer datasheet for the intended application. Typical uses include amplifying the voltage across a low-side shunt, conditioning resistive sensor outputs, and providing gain around analog-control loops. The amplifier can also serve as a buffer when its input bias and noise characteristics meet the system requirements. In each circuit, resistor values should establish suitable gain while keeping the operating point within the device input and output ranges. For PCB implementation, place the device close to the signal source and receiver to minimize susceptibility to noise and parasitic loading. Keep high-current switching paths away from input and feedback nodes, provide a stable decoupling capacitor at the supply pins, and route the feedback loop compactly. Confirm stability with the selected gain and output-load configuration rather than assuming that a generic compensation arrangement fits every application. This page organizes the LM2904FVM-GTR for engineers evaluating dual ground-sense amplifier requirements, including its 3 V to 32 V supply range, 8-MSOP format, use cases, sourcing considerations, and the engineering checks needed before committing a PCB footprint. Use the manufacturer product page and datasheet for final electrical, environmental, and ordering validation.

RFQ Kontak
LM2904ITP/NOPB - Dual 26V 700kHz Op Amp | Texas Instruments
LM2904ITP/NOPB

LM2904ITP/NOPB - Dual 26V 700kHz Op Amp | Texas Instruments

The Texas Instruments LM2904ITP/NOPB is a dual, general-purpose operational amplifier with a 26 V maximum supply voltage and a 700 kHz rated operating bandwidth, supplied in an 8-DSBGA package. The ordering suffix identifies the tape-and-reel configuration. Its two amplifier circuits, 1 MHz gain-bandwidth product and 0.1 V/us slew rate place it in the classic low-power, general-purpose operational-amplifier category. An operational amplifier, or op amp, is a voltage-controlled differential amplifier intended to amplify the difference between two input voltages. It belongs to the amplifier IC hierarchy, within the broader semiconductor and analog signal-processing categories. A dual op amp combines two amplifier channels in one package, allowing a circuit to implement two signal-processing functions while reducing board area and the number of external components. The LM2904ITP/NOPB is identified as a standard general-purpose amplifier. The listed electrical characteristics include a 26 V maximum supply voltage, 700 kHz operating bandwidth, 1 MHz gain-bandwidth product and 0.1 V/us slew rate. These values position the device for moderate-frequency signal handling rather than high-speed precision work. The 8-DSBGA package also gives PCB designers a compact option for dual-channel analog circuits. The device belongs to the long-established LM2904 family and is associated with the LM158-series operating-amplifier architecture, consisting of two independent, high-gain, internally frequency-compensated amplifiers designed for single-supply operation over a wide voltage range. Internal frequency compensation removes the need for an external dominant-pole capacitor in typical closed-loop configurations, simplifying implementation and stabilizing operation across supported gain settings. Typical uses include low-frequency sensor conditioning, audio preamplification, instrumentation, active filtering, and general dual-amplifier analog signal chains. The dual-channel configuration is particularly useful when a design needs symmetric gain stages, a voltage follower alongside a signal amplifier, or two related sensor interfaces sharing one compact package. Designers should verify the exact input common-mode range, output swing, input offset, input-bias current, supply-current behavior and temperature limits against the manufacturer datasheet before finalizing a circuit. Place the 8-DSBGA on a PCB layout that separates input, output and supply paths appropriately, and use suitable bypassing capacitance at the power pins. Because the package is a fine-pitch BGA rather than a leaded package, assembly capability and land-pattern compatibility also require verification. This product page organizes the confirmed ordering, package, electrical, and commercial information while distinguishing documented LM2904-family options from unconfirmed substitutions. It also provides application guidance, comparison fields, and a pinout limitation notice so engineers can make a package-aware sourcing decision without assuming that every electrically similar dual op amp is a true drop-in replacement.

RFQ Kontak
LM2904ITPX/NOPB - Dual 26V, 700kHz Op Amp | Texas Instruments
LM2904ITPX/NOPB

LM2904ITPX/NOPB - Dual 26V, 700kHz Op Amp | Texas Instruments

Texas Instruments LM2904ITPX/NOPB is a dual, general-purpose operational amplifier with two independent, internally frequency-compensated amplifiers, a maximum supply rating of 26 V, and a gain-bandwidth product of 700 kHz. The device is supplied in an 8-DSBGA package and is intended for single-supply operation across a broad voltage range. An operational amplifier, commonly called an op amp, is an analog integrated circuit that amplifies the voltage difference between its differential inputs. Its high open-loop gain, negative feedback operation, and internal frequency compensation make it useful for signal conditioning, comparison, filtering, and instrumentation. The LM2904 contains two amplifier channels in one package, allowing one IC to serve two related analog functions. The LM2904ITPX/NOPB provides two amplifier circuits in a compact 8-DSBGA package. Texas Instruments describes the device as a low-power dual operational amplifier with a 700 kHz gain-bandwidth product. A listing for the exact MPN also identifies a 0.1 V/µs slew rate, surface-mount construction, and a -40°C to 85°C temperature range. Tape-and-reel packaging supports automated assembly and high-volume production. Internally frequency compensation means each amplifier can operate with a minimum closed-loop gain determined by its internal design rather than requiring an external compensation network in ordinary applications. This characteristic simplifies analog circuit implementation, although the closed-loop gain, output swing, stability, and supply headroom still require verification against the operating conditions of the final circuit. Typical uses for the LM2904ITPX/NOPB include industrial sensor conditioning, instrumentation, low-frequency active filtering, analog signal buffering, and general-purpose dual-amplifier circuits. The 26 V maximum supply rating is useful for industrial and automotive-adjacent designs that operate above conventional 5 V analog rails, provided the applied voltage remains within the device rating and suitable input and output common-mode conditions are maintained. For PCB design, place decoupling capacitors close to the supply and ground connections, preserve the package footprint and pin assignments, and verify thermal performance when both channels operate continuously. Decoupling and stability depend on the source impedance, load, feedback network, and supply arrangement, so prototype the final filter or amplifier configuration before high-volume production. This product page combines the exact-orderable MPN, electrical attributes, package information, application guidance, and practical design considerations. It also distinguishes documented drop-in alternatives from functional equivalents that require different footprints, helping engineers avoid substitutions that cannot be mounted safely on the original PCB land pattern.

RFQ Kontak
LM2904LVIDDFR - 5.5V Dual 1MHz Op Amp | Texas Instruments
LM2904LVIDDFR

LM2904LVIDDFR - 5.5V Dual 1MHz Op Amp | Texas Instruments

The Texas Instruments LM2904LVIDDFR is a dual, low-voltage operational amplifier with a 5.5 V maximum supply voltage, 1 MHz gain-bandwidth product, and 3 mV output offset voltage, housed in an 8-pin TSOT-23 package. Each amplifier channel provides independent input, output, power, and feedback connections, allowing one package to implement two signal-processing functions. An operational amplifier is an analog amplifier whose high open-loop gain is controlled by external feedback components. Within the power-management semiconductor hierarchy, the LM2904LV belongs to the broader operational-amplifier family, combining low-voltage compatibility, low power consumption, and general-purpose signal conditioning in one dual-channel device. The LM2904LV family is intended for portable equipment, industrial controls, sensors, communications, and other low-voltage systems. Key characteristics include a 2.7 V to 5.5 V supply range, approximately 90 uA supply current, a typical slew rate of 0.5 V/us, and rail-to-rail output swing. The 1 MHz gain-bandwidth product supports moderate-frequency amplification, while the 3 mV offset-voltage figure defines the typical input imbalance that must be considered when operating near the output range limits. These characteristics make the device suitable for battery-powered instrumentation and general-purpose analog front ends. The dual architecture reduces component count and board area compared with two separate single-channel amplifiers. Each channel can be configured as an inverting amplifier, a non-inverting amplifier, a comparator-like comparator configuration, or an analog buffer when operated with suitable feedback and loading. Independent channel use provides flexibility, although common-mode and output-swing limitations still apply to both channels. Typical uses include current-sense amplifier front ends, sensor signal conditioning, low-frequency active filters, audio preamplification, industrial interface circuits, and portable measurement equipment. In current sensing, the device can amplify the small voltage developed across a low-value shunt resistor. In sensor interfaces, it can provide gain or impedance conversion before an ADC input. Its low 90 uA supply-current characteristic is particularly useful in battery-operated equipment. When designing around the LM2904LVIDDFR, verify the input common-mode range and output swing against the actual signal amplitude. Keep feedback-loop routing compact, provide local supply bypassing, and avoid placing the input node beside high-current switching paths. Check the 5.5 V maximum supply rating and ensure the 2.7 V lower operating limit is sufficient for the complete system supply range. This product page consolidates the manufacturer specifications, package information, practical application guidance, and verified substitution assessment for the LM2904LVIDDFR. It also distinguishes confirmed drop-in candidates from devices that require a package or functional change, helping engineers evaluate replacements without changing PCB requirements.

RFQ Kontak
LM2904LVIDGKR - Dual 5.5V 1MHz Op Amp | Texas Instruments
LM2904LVIDGKR

LM2904LVIDGKR - Dual 5.5V 1MHz Op Amp | Texas Instruments

The Texas Instruments LM2904LVIDGKR is a dual, low-voltage operational amplifier designed for single-supply or dual-supply industrial and instrumentation circuits. It provides two amplifier channels, a 1 MHz gain-bandwidth product, a 3 mV maximum input offset voltage, and operation from a single 2.7 V to 5.5 V supply in an 8-pin VSSOP (DGK) package. The part is intended for general-purpose signal conditioning where low supply voltage, modest bandwidth, and short-circuit tolerance are more important than high-speed performance. An operational amplifier is an analog integrated circuit that amplifies the difference between its inverting and non-inverting inputs. Within the broader hierarchy, the LM2904LV is a voltage-feedback operational amplifier, which places it in the amplifier IC and analog signal-conditioning categories. Two independent channels allow one package to implement two amplifiers, reducing component count and simplifying board layout in designs such as sensor conditioning, active filtering, and low-frequency instrumentation. Key features include the dual-channel configuration, 1 MHz gain-bandwidth product, 3 mV input offset voltage rating, and a maximum 5.5 V supply voltage. The low-voltage LM2904LV family is intended for portable and low-voltage systems where the conventional 26 V LM2904 would be excessive. Its general-purpose positioning also makes it useful as a cost-conscious alternative to higher-performance precision amplifiers when the signal bandwidth and offset requirements are moderate. The device uses a conventional complementary-input architecture suitable for closed-loop voltage feedback. Because its unity-gain bandwidth is 1 MHz, applications are generally limited to low-frequency amplification and filtering rather than high-speed signal chains. Input and output stability depends on the surrounding feedback network, source impedance, load, and bypass capacitance, so the manufacturer datasheet should be used when selecting compensation and decoupling values. Typical uses include sensor-amplifier front ends, transducer signal conditioning, active low-pass filters, audio preamplifier stages, buffer stages, and general dual-amplifier analog boards. The low-voltage supply range makes the device appropriate for 3.3 V and 5 V systems, although rail-to-rail input and output capability is not implied by the 5.5 V maximum supply specification. The primary design consideration is supply headroom. Common-mode input voltage, output swing, and output-current capability all depend on the selected supply voltage and load. Verify those limits against the application before committing to the VSSOP footprint. Decoupling capacitors should be placed close to the supply pins, and unused amplifier channels should be configured according to the manufacturer datasheet rather than left floating. This page consolidates the device specifications, ordering information, package details, application guidance, and engineering trade-offs into one reference for component selection and PCB design.

RFQ Kontak
LM2904LVIDR - 1MHz Dual Low-Voltage Op Amp | Texas Instruments
LM2904LVIDR

LM2904LVIDR - 1MHz Dual Low-Voltage Op Amp | Texas Instruments

The Texas Instruments LM2904LVIDR is a dual, low-voltage, general-purpose operational amplifier with a 5.5 V maximum supply rating, 1 MHz gain-bandwidth product, and 3 mV input offset voltage. It is supplied in an 8-pin SOIC package and is designed for cost-sensitive signal-conditioning and analog-instrumentation applications. An operational amplifier, or op amp, is an analog integrated circuit that amplifies the difference between two input voltages. The LM2904LVIDR contains two amplifiers in one package, making it useful for dual-channel signal chains, buffer stages, transducers, and low-voltage control systems. Its family position is operational amplifier -> voltage-feedback amplifier -> analog amplifier -> integrated circuit. The device is specified for dual operation at a 5.5 V maximum supply. Texas Instruments describes the LM2904LV as a dual, 5.5 V, 1 MHz operational amplifier with a 3 mV offset-voltage rating. The 8-SOIC package supports conventional surface-mount assembly, while the dual configuration reduces board area for applications that need two amplifier channels. The LM2904LVIDR is intended for instrumentation and general-purpose analog designs where a low-voltage supply is important. Typical uses include sensor-interface amplification, audio signal conditioning, process-control loops, and buffering of low-level analog signals. The 1 MHz bandwidth is suitable for moderate-frequency rather than high-speed precision applications, and the 3 mV input offset specification should be considered in sensor and instrumentation designs requiring low input-level accuracy. For stable operation, follow the manufacturer's recommended supply, common-mode input, output-voltage, and decoupling guidelines from the LM2904LV datasheet. Place the supply bypass capacitor close to the device and keep sensitive input routing short to reduce noise pickup. The two amplifier channels in the package are independent, but each requires correct biasing and appropriate output-load conditions. This product summary combines the LM2904LV family specifications with practical guidance for PCB layout, application selection, and replacement planning. It is designed to help engineers identify whether the 8-SOIC dual op amp meets the voltage, bandwidth, offset, and package requirements of a new analog design.

RFQ Kontak
LM2904LVIPWR - Dual 5.5V 1MHz Op Amp | Texas Instruments
LM2904LVIPWR

LM2904LVIPWR - Dual 5.5V 1MHz Op Amp | Texas Instruments

Texas Instruments LM2904LVIPWR is a dual, general-purpose operational amplifier with a 5.5 V maximum supply rating, 1 MHz gain-bandwidth product, and 3 mV input offset voltage in an 8-pin TSSOP (PW) package. The two amplifiers are intended for low-voltage signal-conditioning and analog-processing systems operating from -40°C to +125°C. An operational amplifier is an active analog component that amplifies the voltage difference between its non-inverting and inverting inputs. The LM2904LV belongs to the LM290xLV low-voltage operational-amplifier family, combining two amplifier channels in one package. This makes the device suitable for applications such as signal buffering, active filtering, differential amplification, instrumentation, and low-level analog conditioning. The headline specifications are a 1 MHz gain-bandwidth product, a 3 mV offset voltage, and a 5.5 V maximum supply rating. These characteristics are useful for moderate-bandwidth, general-purpose analog designs where compactness and dual-channel functionality matter more than high-speed precision performance. The operating-temperature range of -40°C to +125°C supports use across industrial and extended-temperature equipment. The LM2904LV uses conventional internal compensation and is configured as a dual operational amplifier. Its 1 MHz bandwidth supports general-purpose closed-loop signal work, while the two channels can implement independent amplifier functions or work together in differential, summing, and feedback configurations. Design calculations should use the manufacturer datasheet for gain-bandwidth behavior, output swing, input common-mode limits, and output-drive capability. Typical uses include sensor-signal conditioning, audio preamplification, industrial control interfaces, low-frequency active filters, and general analog buffers. In dual-rail or single-supply systems, the circuit designer must verify the allowable input and output common-mode ranges against the actual supply voltage. Output loading and feedback-loop stability also require evaluation when driving capacitive or long external cables. Use the manufacturer pin-description table when assigning PCB tracks and verify the exposed-pad requirements and recommended land pattern for the TSSOP package. Place input and feedback components close to the relevant amplifier pins, maintain short ground-return paths, and provide local supply bypassing to reduce noise and prevent feedback from unrelated circuitry. This product page combines the key manufacturer specifications, ordering and package information, application guidance, and replacement-selection considerations in one engineering-focused reference. The comparison and design notes are intended to accelerate schematic selection, footprint verification, and first-board bring-up for dual low-voltage operational-amplifier designs.

RFQ Kontak
LM2904LVQDGKRQ1 - 5.5V 1MHz Automotive Dual Op Amp | Texas Instruments
LM2904LVQDGKRQ1

LM2904LVQDGKRQ1 - 5.5V 1MHz Automotive Dual Op Amp | Texas Instruments

Texas Instruments LM2904LVQDGKRQ1 is an automotive-grade, dual operational amplifier designed for low-voltage signal-chain systems. It operates from a 2.7 V to 5.5 V supply, provides a 1 MHz gain-bandwidth product, and is specified with a 3 mV input offset voltage. The device is supplied in an 8-VSSOP package and provides two amplifier circuits in one package. An operational amplifier is an analog integrated circuit that uses high-gain differential amplification to compare an inverting input with a non-inverting input. Within the broader hierarchy, it is a voltage-feedback amplifier, an amplifier IC, and a signal-conditioning semiconductor. The dual configuration allows one device to process two related channels, reducing board area when both channels share the same supply and ground reference. The LM2904LV-Q1 family targets automotive and industrial low-voltage applications where supply efficiency, cost, and dependable operation are important. The 2.7 V to 5.5 V operating range supports systems powered from regulated 3.3 V and 5 V rails. Its 1 MHz bandwidth makes it suitable for general-purpose amplification, buffering, voltage comparison, filtering, and sensor-interface functions rather than high-speed signal processing. The dual amplifier architecture is useful in sensor conditioning, current sensing, control loops, line-driver buffers, and automotive body electronics. Each amplifier can be used independently, allowing the two channels to monitor complementary signals or perform separate functions in a compact circuit. Input and output stability, common-mode range, and output-drive capability should be checked against the actual signal levels and load conditions. The principal design trade-off is that this is a general-purpose, low-voltage amplifier rather than a precision or high-speed device. Its 3 mV offset specification is appropriate for many sensing and control paths, but systems requiring tighter offset accuracy need to evaluate the bias current, input voltage range, noise, and application error budget. This page combines the manufacturer specifications, package information, application guidance, comparison parameters, and practical drop-in selection notes for engineers evaluating the LM2904LVQDGKRQ1.

RFQ Kontak
LM2904LVQDRQ1 - 5.5V Dual 1MHz Op Amp | Texas Instruments
LM2904LVQDRQ1

LM2904LVQDRQ1 - 5.5V Dual 1MHz Op Amp | Texas Instruments

Texas Instruments LM2904LVQDRQ1 is an automotive-grade, dual operational amplifier with a 5.5 V maximum supply, 1 MHz gain-bandwidth product, and 3 mV output offset voltage in an 8-pin SOIC package. The two independent channels make it suitable for signal conditioning, transducer amplification, feedback control, and automotive electronics operating from 2.7 V to 5.5 V. An operational amplifier, or op amp, is a voltage-feedback amplifier used to increase signal amplitude, buffer inputs, implement active filters, and regulate feedback loops. Within the semiconductor hierarchy, the LM2904LV-Q1 belongs to the operational-amplifier, analog-amplifier, and signal-conditioning IC categories. Its low-voltage supply operation distinguishes it from conventional high-voltage LM2904 devices while retaining the familiar dual-channel pin arrangement. The LM2904LV-Q1 family is specified for low-voltage operation from 2.7 V to 5.5 V. Its 1 MHz gain-bandwidth product supports general-purpose closed-loop amplification at relatively low frequencies. The 3 mV offset specification improves DC accuracy in applications where input bias and offset errors influence the output. Two amplifiers are integrated in one 8-pin SOIC, reducing board area while providing independent channels for complementary signal paths. This device is intended for cost-sensitive, low-voltage systems that still require automotive-grade temperature qualification and robust general-purpose performance. The dual configuration can implement two noninverting amplifiers, two voltage followers, differential signal conditioning, or independent error-amplifier functions. Because it is not rail-to-rail, input and output common-mode ranges must remain within the device's specified operating limits when supplies are restricted. Typical uses include automotive sensor interfaces, body and comfort-system signal conditioning, low-voltage control loops, current sensing with external resistors, active filters, and general industrial modules operating from 2.7 V or 3.3 V rails. A 5 V system can use the full 5.5 V maximum supply while retaining appropriate design margin for supply variation and transient behavior. When laying out the circuit, keep input and feedback traces short, provide local supply bypassing, and avoid placing long routes beside high-current switching nodes. Check the common-mode input range at the actual signal amplitude and ensure that output swing remains below the output-current and supply-voltage limits. Decoupling capacitors should connect directly to the supply and ground pins rather than through shared narrow traces. This product page combines the manufacturer specifications with practical design guidance, package-level comparisons, application examples, and available drop-in alternatives. It supports faster component selection for engineers who need a dual, low-voltage, automotive operational amplifier in the standard 8-pin SOIC footprint.

RFQ Kontak
LM2904M - Dual 26V 700kHz Op Amp | Texas Instruments
LM2904M

LM2904M - Dual 26V 700kHz Op Amp | Texas Instruments

The Texas Instruments LM2904M is a dual, general-purpose operational amplifier with a 26 V supply rating, 700 kHz gain-bandwidth product, and an 8-SOIC package. According to the Texas Instruments LM2904 product page, the device is intended for low-power analog signal-processing systems where two amplifiers are useful in a single package. The verified distributor listing identifies LM2904M as a standard two-circuit amplifier in an 8-SOIC package, and the Mouser result specifies the operating-temperature range as -40 °C to 85 °C. An operational amplifier is an analog integrated circuit that uses feedback to amplify the difference between its non-inverting and inverting inputs. The LM2904M belongs to the broader operational-amplifier, analog-amplifier, and semiconductor hierarchies. In practical circuits, each internal amplifier can serve as an inverting amplifier, non-inverting amplifier, comparator, buffer, or integrator when operated with suitable external components and supply voltages. The 26 V supply rating provides compatibility with conventional industrial and analog signal ranges, while the 700 kHz gain-bandwidth product supports low-to-moderate-frequency signal amplification. The dual configuration reduces package count when a circuit needs two amplifier channels. Its general-purpose designation indicates broad applicability rather than a specialized low-noise, high-speed, precision, or automotive-only function. The LM2904M uses an 8-SOIC surface-mount package, corresponding to the soic-8 package library key. The verified results do not provide a complete electrical specification table in the supplied excerpts, so detailed parameters such as input offset voltage, input bias current, slew rate, output-current capability, common-mode range, quiescent current, and noise values are marked as data needed rather than estimated. Typical applications include low-frequency analog signal conditioning, instrumentation interfaces, sensor buffers, audio preamplifier stages, and general dual-amplifier circuits. The dual channel can also be used for active filtering or control loops where two matched functional amplifier sections are useful. Because the available information is general-purpose and distributor-oriented, the designer should verify operating-point limits, loading, stability, and temperature margin against the manufacturer datasheet before release. For PCB implementation, place bypass capacitors close to the supply pins and route sensitive input and feedback traces away from switching nodes and high-current paths. Confirm the exact pin orientation and electrical limits before assembly. This page combines verified manufacturer and distributor references with explicitly marked data gaps rather than inventing missing specifications.

RFQ Kontak
LM2904M-FS - Dual 26V Op Amp 500V/ms | onsemi
LM2904M-FS

LM2904M-FS - Dual 26V Op Amp 500V/ms | onsemi

The onsemi LM2904M-FS is a dual general-purpose operational amplifier in an 8-pin SOIC package, with two independent internally frequency-compensated amplifier channels designed for operation from a single power supply. Key characteristics include a 250 nA input-bias current, 500 V/ms slew rate, and approximately 2 mV input offset voltage for the listed configuration. An operational amplifier is an analog signal-conditioning IC that compares an inverting input with a non-inverting input and amplifies the voltage difference between them. The dual-amplifier configuration places two independent amplifiers in one package, making the LM2904M-FS suitable for signal conditioning, feedback-control loops, sensor amplification, and general analog signal paths. Within the product hierarchy, it is a dual operational amplifier within the amplifier-IC and analog-semiconductor categories. The LM2904M-FS combines a 26 V maximum supply capability from the LM2904 family with low input-bias current and a 500 V/ms slew rate. Its internally compensated architecture removes the need for an external frequency-compensation network in common closed-loop applications. The two independent channels can operate in non-inverting, inverting, voltage-follower, comparator-style, and feedback configurations, provided the design respects the device's common-mode and output-voltage limits. The 8-SOIC footprint provides a conventional surface-mount assembly format with exposed leads on both package sides. Each half of the amplifier uses four pins: two inputs, one output, and the power connection. The standard SOIC-8 pin arrangement simplifies PCB layout, but normal single-supply operation requires bypassing the positive supply pin to ground and accounting for the input and output common-mode limitations near the supply rails. Typical applications include low-frequency industrial instrumentation, buffered sensor interfaces, audio preamplifier stages, analog monitoring, and general-purpose dual-amplifier signal conditioning. The LM2904M-FS is particularly useful where two related analog channels are required on one board, such as an input stage and feedback amplifier in a control circuit. For high-speed or very low-offset instrumentation, a precision amplifier family may be preferable. Decouple the power supply with a short, low-inductance path from the positive supply pin to ground, and route the amplifier output away from high-current switching nodes. Avoid using the device outside its input common-mode range, especially in single-supply circuits where the input approaches ground. Stable feedback-network layout and adequate output-load capability should be verified for every analog channel. This product page combines the exact LM2904M-FS ordering information with family-level electrical characteristics, a complete SOIC-8 pin map, practical application guidance, and a qualified drop-in comparison. It is designed to help engineers identify the correct footprint, understand the device's analog signal-conditioning role, and select among documented alternatives without changing the PCB land pattern.

RFQ Kontak
LM2904M/NOPB - Dual 26V 700kHz Op Amp | Texas Instruments
LM2904M/NOPB

LM2904M/NOPB - Dual 26V 700kHz Op Amp | Texas Instruments

Texas Instruments LM2904M/NOPB is a dual, low-power, high-gain operational amplifier rated for a 26 V supply and a 700 kHz gain-bandwidth product. The device is supplied in an 8-pin SOIC package and provides two independent, internally frequency-compensated amplifiers. It is designed for operation from a single power supply over a wide voltage range, while split-supply operation is also supported. The LM2904 family targets general-purpose analog signal conditioning where low power consumption, wide supply-voltage tolerance, and conventional dual-amplifier pin arrangements are important. An operational amplifier is an analog signal-processing IC that uses high open-loop gain to amplify differences between voltages applied to its inverting and non-inverting inputs. A dual operational amplifier contains two amplifier sections in one package, reducing board area and simplifying designs that require two independent gain stages. Within the broader semiconductor hierarchy, the LM2904 is an amplifier IC, then an operational amplifier, and finally a general-purpose analog building block for instrumentation, control, and signal-conditioning systems. Key characteristics include a 26 V maximum supply rating, a 700 kHz gain-bandwidth product, low-power operation, internally compensated frequency response, and operation across single- and split-supply arrangements. These features make the LM2904M/NOPB appropriate for transducers, low-frequency analog filters, sensor amplifiers, and general feedback-control circuits. The manufacturer describes the device as a dual low-power, high-gain operational amplifier specifically designed for single-supply operation over a wide range of voltages. Internally, each amplifier section uses frequency compensation to provide stable closed-loop operation without requiring an external compensation network. The two sections are independent, allowing them to serve separate signal paths or to work together as stages within a larger analog circuit. The 700 kHz gain-bandwidth product favors low-frequency rather than high-speed signal applications, while the 26 V supply rating provides useful headroom for industrial and automotive-style supply environments when the complete circuit satisfies the device ratings. Typical uses include amplifying outputs from sensors, buffering potentiometer and resistive-divider signals, implementing active low-pass or high-pass filters, and closing loops around slow analog control systems. Two amplifiers in one 8-pin SOIC can also form instrumentation-style signal-conditioning chains when the required common-mode range, output swing, and noise performance match the application. For PCB design, verify the exact pin orientation and exposed or non-exposed package details against the manufacturer pin configuration before routing copper. Place input and feedback components close to the relevant amplifier pins, maintain short ground-return paths, and use a stable local supply-decoupling arrangement. Avoid designs requiring the high slew rate and wide bandwidth of precision or high-speed amplifiers; the LM2904 is better suited to economical, general-purpose low-frequency analog functions. This product page consolidates the manufacturer family specifications, verified distributor identification, same-footprint alternatives, application guidance, and practical design considerations. It supports faster part identification while keeping datasheet verification, footprint review, and application-specific validation at the center of every engineering decision.

RFQ Kontak
LM2904M8-13 - Dual 700 kHz Op Amp | Diodes Incorporated
LM2904M8-13

LM2904M8-13 - Dual 700 kHz Op Amp | Diodes Incorporated

The Diodes Incorporated LM2904M8-13 is a dual general-purpose operational amplifier with two independent amplifier channels, a 700 kHz gain-bandwidth product, 2 mV input offset voltage, and an 8-MSOP package. It operates from a single supply between 3 V and 36 V, while split-supply operation is also supported. The device is characterized for industrial temperatures from -40°C to +125°C and uses green mold compound as standard. An operational amplifier is an analog signal-conditioning IC that amplifies the voltage difference between its inverting and non-inverting inputs. Operational amplifiers belong to the amplifier IC hierarchy and are widely used in sensor interfaces, filters, comparators, feedback-control loops, and low-frequency signal-processing circuits. The LM2904 combines two operational amplifiers in one compact surface-mount package, reducing board area compared with separate single-channel devices. Each LM2904 channel provides high open-loop gain and a 700 kHz gain-bandwidth product. The 2 mV input offset rating helps limit output error in DC amplifier and comparator circuits. Single-supply operation from 3 V to 36 V makes the device suitable for industrial control, instrumentation, sensor-conditioning, and power-supply feedback applications. Its -40°C to +125°C characterization also supports designs operating across extended temperature ranges. The LM2904 architecture supports both single-supply and split-supply operation. In a single-supply circuit, the input common-mode range, output swing, and bias arrangement remain important design constraints, particularly when signals remain close to ground. With dual supplies, the two amplifier channels can process signals around ground more naturally, although common-mode and output-range checks remain necessary at the supply limits. Typical uses include transimpedance amplifiers for low-frequency sensor signals, active filters for analog signal conditioning, threshold detectors, and closed-loop control amplifiers. The two channels may also be configured as a comparator, voltage follower, or differential amplifier, depending on the feedback network and system voltage requirements. Its 8-MSOP package is suited to compact industrial and embedded control boards where a dual amplifier offers practical space savings. For reliable layout, place input and feedback components close to their corresponding pins and keep sensitive input traces away from high-current switching paths. The power-supply pins require effective bypassing with a short ground return. Confirm that input and output signal levels remain inside the amplifier's usable common-mode and output ranges, particularly in single-supply configurations where the available signal headroom is reduced. This page combines the manufacturer datasheet, distributor listings, package and pinout information, application guidance, and replacement-selection criteria to support faster engineering evaluation. Review the electrical limits and application circuit in the Diodes Incorporated LM2904/LM2902 datasheet before finalizing a production design.

RFQ Kontak