DG412EUE+ - Quad SPST Analog Switch | Analog Devices
MPN: DG412EUE+ ✓ NakahandaDG412EUE+ Ulas
An analog switch is a semiconductor device that connects or disconnects signal paths under digital control. As an analog switch, the DG412EUE+ belongs to the broader switch IC and interface IC hierarchy. Its four SPST channels provide independent normally open paths, allowing one controller to select among several analog sources or destinations while preserving the selected signal without converting it to a digital representation.
The DG412 family is engineered for improved channel matching, with on-resistance matching specified at no more than 3 ohms. Guaranteed on-resistance flatness across the signal range is specified at no more than 4 ohms. These characteristics reduce channel-to-channel gain variation and distortion when multiple switched paths must operate consistently. The DG412EUE+ also provides bidirectional operation, allowing each SPST path to conduct signal flow in either direction.
The compact 16-pin TSSOP package supports surface-mount PCB assembly and provides access to four control inputs, four analog terminals, ground connections, and positive supply connections. Device control and signal-path details must be assigned using the pin-description table in the manufacturer datasheet. The EUE ordering code identifies the 16-pin TSSOP configuration, while the trailing plus sign denotes the manufacturer's improved product designation.
Typical uses include automated test equipment, instrumentation, communications routing, sample-and-hold systems, and peripheral-selection networks. The four independent SPST switches are especially useful where one board must route several precision analog channels without adding mechanical relays. Because the switch resistance and flatness characteristics are controlled, engineers can evaluate insertion loss and channel matching across the intended signal range rather than relying only on the nominal 45-ohm value.
PCB design should keep analog routes short and symmetric, place decoupling capacitance close to the supply pins, and provide adequate return paths for control and switched signals. The TSSOP footprint offers finer routing density than a larger SOIC package, but it requires careful land-pattern construction and clean assembly practices. Verify logic levels, supply voltage, signal-range limits, and switching conditions in the manufacturer datasheet before finalizing the interface circuit.
This page combines the production status, package information, switch characteristics, thermal limits, and available drop-in comparison information into an application-oriented resource. It also identifies design considerations that help engineers evaluate the DG412EUE+ alongside pin-compatible alternatives without overlooking package, control-interface, or signal-integrity differences.
Mga alternatibo na pwedeng ilagay na DG412EUE+ — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.
DG412CUE+
✅ Drop-In📋 Alternatibo na Reference (hindi sa katalogo)
DG412EUE+ Mga Pinakamataas na Rating at Electrical Characteristics
| Number of Switches | 4 circuits |
| Switch Configuration | Quad SPST, normally open |
| Multiplexer Configuration | 1:1 |
| Nominal On Resistance | 45 ohm |
| On-Resistance Matching | 3 ohm maximum |
| On-Resistance Flatness | 4 ohm maximum |
| Signal Conduction | Bidirectional |
| Hanay ng Temperature na Operasyon | -40°C to +85°C |
| Packhaging | 16-pin TSSOP |
| Uri ng Pagpapasok | Surface mount |
| Production Status | Production |
| Packaging | Tube |
Gabay sa Pin Configuration ng DG412EUE+ 16-pin tssop
Pin configuration para sa DG412EUE+ (16-pin tssop package). Ang pagnunumero ng pin, mga function, at connection diagram ay tinukoy sa datasheet ng manufacturer. Sumangguni dito para sa eksaktong footprint at mga alituntunin sa soldering.
Wala ng detalyadong pinout data na magagamit para sa DG412EUE+.
Sumangguni sa datasheet para sa buong pin configuration.
Tipikal na mga Gamit
DG412EUE+ ay nararapat para sa 6 aplikasyons: Automated Test Equipment Signal Routing, Precision Measurement and Instrumentation, Communications Path Selection, Sample-and-Hold Signal Selection, Sensor Signal Multiplexing, Data Acquisition Channel Isolation.
Automated Test Equipment Signal Routing
The DG412EUE+ fits automated test equipment that must connect multiple analog sources, instruments, or fixtures through independent paths. Its four SPST 1:1 channels provide straightforward routing control, while the 45-ohm nominal on resistance establishes the basic insertion-loss budget. Channel matching of no more than 3 ohms and on-resistance flatness of no more than 4 ohms help limit measurement variation between paths. Use the switch near the routed nodes and place supply decoupling close to the TSSOP power pins. Exact logic levels, signal-range limits, and control timing should be confirmed in the manufacturer datasheet before connecting precision front ends.
Inirekomenda
Precision Measurement and Instrumentation
The DG412EUE+ is useful in measurement instruments that require controllable analog paths without mechanical relay switching. Four independently controlled, normally open SPST channels can select test inputs, attenuator networks, sensors, or reference paths. The controlled 3-ohm maximum on-resistance matching is important when comparing readings across multiple channels, and the 4-ohm maximum flatness specification reduces variation over the usable signal range. Account for the nominal 45-ohm resistance in the gain and noise budget, use short PCB routes, and verify leakage, bandwidth, and analog-signal limits for the specific operating conditions.
Inirekomenda
Communications Path Selection
The DG412EUE+ can serve as a low-frequency communications path-selection element when four bidirectional SPST channels are sufficient. Bidirectional conduction allows each path to support signal flow in either direction, while independent control supports channel isolation and routing between multiple nodes. The 45-ohm nominal on resistance and 4-ohm maximum flatness must be included in the channel loss calculation, especially near the upper end of the supported signal range. Confirm supply voltage, control thresholds, leakage, and switching transients against the DG412 datasheet, and keep the compact TSSOP routing symmetrical to minimize parasitic differences.
Inirekomenda
Sample-and-Hold Signal Selection
The DG412EUE+ can select among several sampled or buffered analog signals in a sample-and-hold subsystem. Its four 1:1 SPST paths make each switched terminal available for connection to a shared acquisition or hold circuit, and the controlled on-resistance matching helps preserve consistency between selections. Because the nominal on resistance is 45 ohms, the downstream buffer must have sufficient input impedance to avoid excessive loading. The 4-ohm maximum on-resistance flatness specification is also relevant when signal amplitude changes across the selected range. Validate settling behavior, control timing, leakage, and allowable signal voltages in the manufacturer datasheet.
Inirekomenda
Sensor Signal Multiplexing
The DG412EUE+ can route low-frequency sensor outputs into a common analog processing path when four independently controlled channels are adequate. Controlled on-resistance matching of no more than 3 ohms reduces channel-dependent amplitude errors, while bidirectional paths provide flexibility when sensors or conditioners are connected in either direction. The 45-ohm nominal resistance should be included in the sensor-source impedance calculation to prevent loading errors. Use a quiet ground plane, minimize analog trace length, and place any required bypass capacitor at the power pins. Confirm input bias current, leakage, and signal-range requirements before selecting the device.
Inirekomenda
Data Acquisition Channel Isolation
The DG412EUE+ supports data-acquisition systems that need to connect or isolate several analog channels under software control. Four normally open SPST switches provide independent paths without crosstalk through an active multiplexer topology. The specified 3-ohm maximum on-resistance matching and 4-ohm maximum flatness help maintain consistency between channels, although the nominal 45-ohm contribution must be included in the input-impedance design. Keep analog routing compact, provide a continuous ground reference, and isolate switching-control traces from sensitive sensor lines. Review leakage, settling time, supply levels, and application-specific qualifications in the manufacturer datasheet.
Inirekomenda
Impormasyon ng Talumpati sa Engineering for DG412EUE+ — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.
Paunawang Hanapin
Ikabit sa Mga Alternatibo
| Parametro | Ito ang Producto | DG412CUE+ |
|---|---|---|
| Brand | Analog Devices | Analog Devices |
| Package | 16-TSSOP | 16-TSSOP - same package |
| Number of Circuits | 4 | 4 |
| Switch Configuration | Quad SPST, normally open | Quad SPST, normally open |
| Multiplexer Configuration | 1:1 | 1:1 |
| Nominal On Resistance | 45 ohm | 45 ohm |
| Signal Conduction | Bidirectional | Bidirectional |
Pangunahing mga Pagkakaiba
- Four controlled analog paths in one compact package (kumpara saDG412CUE+)
- Controlled resistance matching for multichannel measurements (kumpara saDG412CUE+)
- Guaranteed flatness across the signal range (kumpara saDG412CUE+)
Talaan ng Disenyo
Place the required supply-decoupling capacitor directly beside the DG412EUE+ supply and ground pins, with a short return path into the ground plane. Route the four switched analog paths away from control-clock and digital-output traces to reduce coupling. Because the device uses a compact 16-pin TSSOP footprint, verify the manufacturer land pattern and pin assignments against the PCB library before releasing fabrication data.
Include the 45-ohm nominal switch resistance in the complete insertion-loss and source-impedance budget. On-resistance matching is specified at no more than 3 ohms, while flatness across the signal range is no more than 4 ohms; both contribute to channel-dependent error. Use short, symmetric routes, provide a continuous reference plane, and confirm leakage and allowable signal limits for the operating voltage and temperature.
Do not select the DG412EUE+ as though it were a zero-resistance or RF-optimized multiplexer. It is a four-channel SPST analog switch with 45-ohm nominal on resistance, and its control, supply, leakage, and signal-range constraints must be respected. Also avoid treating the DG412CUE+ as an automatic substitute until the ordering-code-specific temperature, qualification, and marking details have been compared.
Maintain comparable geometry for the four analog channels so that parasitic capacitance and inductance do not introduce more variation than the switch itself. Keep the exposed switched nodes away from unrelated high-impedance inputs, and place any downstream buffer close enough to minimize additional transmission-line effects. The same layout discipline is especially important because the datasheet limits on-resistance matching and flatness, but it does not eliminate PCB-induced differences.
Impormasyon ng Pagsunod sa Kautusan
The product listing references RoHS, but it does not state a definitive compliance result. Use the manufacturer product page or datasheet for current environmental, material, and qualification declarations.