LM258YDT - Dual 1.1 MHz Op Amp, 8-SOIC | STMicroelectronics
MPN: LM258YDT ✓ NakahandaLM258YDT Ulas
An operational amplifier is an analog semiconductor that uses high open-loop gain to amplify voltage differences. Its broader hierarchy is operational amplifier, analog amplifier, linear integrated circuit, and semiconductor. Internally frequency-compensated devices simplify closed-loop design because they do not require an external compensation network for common gain configurations. The LM258 family is therefore useful when designers need stable voltage gain with fewer external components.
The principal published characteristics include a large DC voltage gain of 100 dB, a unity-gain bandwidth of 1.1 MHz, and low input bias current of 20 nA. Its low-power architecture provides very low supply current per amplifier, essentially independent of supply voltage according to the manufacturer datasheet. The two independent amplifier channels can implement separate gain stages, buffers, comparators, or active-filter sections within one package.
The internally compensated architecture provides stable operation in voltage-follower and non-inverting configurations. A 1.1 MHz unity-gain bandwidth makes the device suitable for audio-frequency signal conditioning, sensor interfaces, and low-frequency control loops. Input bias current of 20 nA helps limit bias-current error when the source impedance is high, while the 0.6 V/us slew rate supports changing waveforms without excessive distortion.
Typical uses include audio preamplification, low-voltage sensor conditioning, active filtering, industrial instrumentation, and general-purpose buffering. Because the package contains two amplifiers, it can reduce board area where two independent analog functions are required. Common-mode range, output swing, supply limits, input offset voltage, and exact channel behavior must be checked against the manufacturer datasheet before final circuit release.
Design the PCB with short feedback paths, stable reference connections, and decoupling capacitors placed close to the supply pins. Confirm output swing and input common-mode limits for the selected supply voltage. Verify noise, offset, and stability requirements with the closed-loop gain and source impedance used in the finished circuit.
This page combines the published LM258YDT characteristics with package details, application guidance, comparison information, and drop-in replacement considerations. It is designed to help engineers identify whether the LM258YDT matches a dual-amplifier requirement before moving to detailed schematic review and qualification.
Mga alternatibo na pwedeng ilagay na LM258YDT — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.
Variante sa Seri na ito
Katulad na modelo sa serye na katugma sa pagpasok LM258YDT (parehas na form factor at footprint) — pagkakaiba sa Package, Input Bias Current, Slew Rate.
LM258DT
✅ Drop-In ⚠️ Mga Talaan Hindi NaiwerikmoMagkontak para sa presyo
Tingnan ang Datasheet →LM258ADT
✅ Drop-In ⚠️ Mga Talaan Hindi Naiwerikmo📋 Alternatibo na Reference (hindi sa katalogo)
LM258AYDT
✅ Drop-In ⚠️ Mga Talaan Hindi Naiwerikmo📋 Alternatibo na Reference (hindi sa katalogo)
LM358DT
✅ Drop-In ⚠️ Mga Talaan Hindi Naiwerikmo✗ Wala sa Stock
$0.0509 / Yunit
Tingnan ang Datasheet →LM358YDT
✅ Drop-In ⚠️ Mga Talaan Hindi Naiwerikmo📋 Alternatibo na Reference (hindi sa katalogo)
LM258YDT Mga Pinakamataas na Rating at Electrical Characteristics
| Product Type | Dual operational amplifier |
| Number of Amplifier Circuits | 2 circuits |
| DC Voltage Gain | 100 dB |
| Unity-Gain Bandwidth | 1.1 MHz |
| Slew Rate | 0.6 V/us |
| Input Bias Current | 20 nA |
| Frequency Compensation | Internally frequency compensated |
| Supply Current Per Amplifier | Very low and essentially independent of supply voltage |
| Automotive Grade | Yes |
| Packhaging | 8-SOIC |
| Uri ng Pagpapasok | Surface mount |
| Bilang ng Pins | 8 pins |
Gabay sa Pin Configuration ng LM258YDT 8-soic
Pin configuration para sa LM258YDT (8-soic package). Ang analog component na ito ay may input, output, at power supply pins. Sumangguni sa datasheet ng manufacturer para sa offset null, compensation, at enable pin configurations. Perpekto para sa signal conditioning at amplifier circuits.
Wala ng detalyadong pinout data na magagamit para sa LM258YDT.
Sumangguni sa datasheet para sa buong pin configuration.
Tipikal na mga Gamit
LM258YDT ay nararapat para sa 6 aplikasyons: Audio Preamplifier, Industrial Sensor Conditioning, Active Filtering, Voltage Buffer, Motor and Control Signal Conditioning, Portable Instrumentation.
Audio Preamplifier
The LM258YDT fits dual-channel audio preamplification because its 1.1 MHz unity-gain bandwidth and 0.6 V/us slew rate support audio-frequency waveforms while the two channels can handle left and right signals independently. Its internally compensated architecture simplifies the gain stage and reduces the need for external compensation components. The 100 dB DC voltage gain provides ample open-loop gain for closed-loop audio amplification. Designers should still confirm output swing against the selected supply voltage and evaluate distortion and noise against the manufacturer datasheet limits.
Inirekomenda
Industrial Sensor Conditioning
The LM258YDT is suitable for conditioning low-bandwidth industrial sensor signals when the source impedance is high and input bias current matters. Its published input bias current of 20 nA helps minimize bias-induced error, while the dual package can amplify or buffer two related channels. The 1.1 MHz unity-gain bandwidth covers many process-control and instrumentation signals. Verify the sensor output range against the LM258YDT common-mode and supply limits, and check the automotive temperature qualification required by the target installation.
Inirekomenda
Active Filtering
The LM258YDT can implement active low-pass, high-pass, or notch-filter sections because the internally compensated dual amplifier provides two signal-processing channels in one 8-SOIC package. A 1.1 MHz unity-gain bandwidth supports filter designs well above conventional audio baseband frequencies, while 100 dB DC gain helps reduce closed-loop gain error. Component tolerances and amplifier stability requirements must be considered for higher-Q filters. Confirm the datasheet gain-bandwidth, noise, and output-swing curves against the selected filter topology.
Inirekomenda
Voltage Buffer
The LM258YDT works well as a dual voltage buffer when a higher-impedance source must drive a downstream measurement or control stage. Internally frequency compensation supports unity-gain voltage-follower use without an external compensation network, and the 0.6 V/us slew rate limits large-signal behavior during rapid input transitions. Both channels can buffer complementary control signals in a compact 8-SOIC footprint. Validate the source and sink current capabilities, output swing, capacitive-load stability, and input common-mode range for the actual operating conditions.
Inirekomenda
Motor and Control Signal Conditioning
The LM258YDT can condition low-frequency position, current, or feedback signals in industrial and automotive control systems. Its 100 dB DC gain is useful when a control-loop amplifier needs high closed-loop accuracy, while the 1.1 MHz unity-gain bandwidth can accommodate feedback signals with moderate frequency content. The dual configuration can process command and feedback channels independently. Because switching nodes and motor returns can create large transients, use careful grounding, isolation, filtering, and common-mode analysis before connecting the amplifier.
Inirekomenda
Portable Instrumentation
The LM258YDT is appropriate for compact, low-power instrumentation because it combines two amplifier channels in an 8-SOIC package and is specified as having very low supply current per amplifier, essentially independent of supply voltage. The 20 nA input bias current is favorable for high-impedance probes, and the 1.1 MHz bandwidth supports measurements beyond the slowest DC regime. A portable design should still examine supply range, shutdown strategy, quiescent current, temperature rise, and battery-voltage variation before selecting operating points and passive components.
Inirekomenda
Buod ng mga Inirekomendang Produkto
Impormasyon ng Talumpati sa Engineering for LM258YDT — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.
Paunawang Hanapin
Ikabit sa Mga Alternatibo
| Parametro | Ito ang Producto | LM258DT | LM258ADT | LM258AYDT | LM358DT | LM358YDT |
|---|---|---|---|---|---|---|
| Package | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC |
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics |
| Amplifier Channels | 2 | 2 | 2 | 2 | 2 | 2 |
| Frequency Compensation | Internal | Internal | Internal | Internal | Internal | Internal |
| Automotive Ordering Option | Yes | No Y ordering designation | No Y ordering designation | Yes | No Y ordering designation | Yes |
| Mounting Type | Surface mount | Surface mount | Surface mount | Surface mount | Surface mount | Surface mount |
Pangunahing mga Pagkakaiba
- Combines two amplifier channels with automotive-oriented ordering (kumpara saLM258DT)
- Higher nominal bandwidth than the LM358 alternatives (kumpara saLM358DT)
- Faster nominal slew rate than the LM358 alternatives (kumpara saLM358YDT)
Talaan ng Disenyo
Place the supply bypass capacitor immediately adjacent to the LM258YDT supply pins and provide a low-impedance return path to the device ground. Keep input and output traces short, particularly around high-gain feedback loops, and avoid routing sensitive inputs beneath digital or switching nodes. Confirm the physical pin-1 orientation and SOIC land pattern against the manufacturer package drawing before layout release.
Keep the LM258YDT feedback components close to the amplifier pins and minimize the feedback-loop area to reduce susceptibility to parasitic capacitance and noise pickup. The device is internally frequency compensated for common configurations, but unusually high noise gain, large capacitive loads, or long feedback traces can still affect stability. Use the manufacturer stability and capacitive-load guidance when the operating conditions differ from the standard test setup.
Check the selected supply voltage against the LM258YDT operating range and verify that every signal remains within the usable input common-mode range. Also confirm output swing at the intended load because a low-power amplifier can approach its output limits before reaching the nominal supply rail. Decoupling capacitance, stability, and maximum output current should be evaluated together rather than treated as independent constraints.
Do not assume that every LM358-family ordering option is an automatic substitute for the LM258YDT. Although related devices can share an 8-SOIC footprint, DC offset, input bias current, common-mode range, output swing, temperature grade, and automotive qualification can differ. Compare the manufacturer datasheet for every production substitution and perform stability, offset, output-swing, and thermal checks on the assembled board.
Impormasyon ng Pagsunod sa Kautusan
The product listing identifies the LM258YDT as automotive grade. Formal RoHS, REACH, AEC-Q100 qualification, lead-free, halogen-free, and conflict-minerals statements are not established by the available component documentation.