LM258YDT - Dual 1.1 MHz Op Amp, 8-SOIC | STMicroelectronics
料号: LM258YDT ✓ 量产中LM258YDT 概述
An operational amplifier is an analog semiconductor that uses high open-loop gain to amplify voltage differences. Its broader hierarchy is operational amplifier, analog amplifier, linear integrated circuit, and semiconductor. Internally frequency-compensated devices simplify closed-loop design because they do not require an external compensation network for common gain configurations. The LM258 family is therefore useful when designers need stable voltage gain with fewer external components.
The principal published characteristics include a large DC voltage gain of 100 dB, a unity-gain bandwidth of 1.1 MHz, and low input bias current of 20 nA. Its low-power architecture provides very low supply current per amplifier, essentially independent of supply voltage according to the manufacturer datasheet. The two independent amplifier channels can implement separate gain stages, buffers, comparators, or active-filter sections within one package.
The internally compensated architecture provides stable operation in voltage-follower and non-inverting configurations. A 1.1 MHz unity-gain bandwidth makes the device suitable for audio-frequency signal conditioning, sensor interfaces, and low-frequency control loops. Input bias current of 20 nA helps limit bias-current error when the source impedance is high, while the 0.6 V/us slew rate supports changing waveforms without excessive distortion.
Typical uses include audio preamplification, low-voltage sensor conditioning, active filtering, industrial instrumentation, and general-purpose buffering. Because the package contains two amplifiers, it can reduce board area where two independent analog functions are required. Common-mode range, output swing, supply limits, input offset voltage, and exact channel behavior must be checked against the manufacturer datasheet before final circuit release.
Design the PCB with short feedback paths, stable reference connections, and decoupling capacitors placed close to the supply pins. Confirm output swing and input common-mode limits for the selected supply voltage. Verify noise, offset, and stability requirements with the closed-loop gain and source impedance used in the finished circuit.
This page combines the published LM258YDT characteristics with package details, application guidance, comparison information, and drop-in replacement considerations. It is designed to help engineers identify whether the LM258YDT matches a dual-amplifier requirement before moving to detailed schematic review and qualification.
直接替换替代料: LM258YDT ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: LM258YDT (相同外形与封装尺寸) ——差异在于 Package, Input Bias Current, Slew Rate.
LM258DT
✅ 直接替换 ⚠️ 规格未核验联系询价
查看数据手册 →LM258ADT
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
LM258AYDT
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
LM358DT
✅ 直接替换 ⚠️ 规格未核验✗ 无现货
$0.0509 / 个
查看数据手册 →LM358YDT
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
LM258YDT 最大额定值与电气特性
| Product Type | Dual operational amplifier |
| Number of Amplifier Circuits | 2 circuits |
| DC Voltage Gain | 100 dB |
| Unity-Gain Bandwidth | 1.1 MHz |
| Slew Rate | 0.6 V/us |
| Input Bias Current | 20 nA |
| Frequency Compensation | Internally frequency compensated |
| Supply Current Per Amplifier | Very low and essentially independent of supply voltage |
| Automotive Grade | Yes |
| 封装 | 8-SOIC |
| 安装类型 | Surface mount |
| 引脚数 | 8 pins |
LM258YDT 8-soic 引脚配置指南
LM258YDT(8-soic 封装)的引脚配置。 该模拟元件具有输入、输出和电源引脚。请参阅制造商数据手册以了解失调调零、补偿和使能引脚配置。适用于信号调理和放大器电路。
暂无详细引脚数据: LM258YDT.
请参阅 数据手册 以查看完整引脚配置。
典型应用
LM258YDT 适用于 6 应用s: Audio Preamplifier, Industrial Sensor Conditioning, Active Filtering, Voltage Buffer, Motor and Control Signal Conditioning, Portable Instrumentation.
Audio Preamplifier
The LM258YDT fits dual-channel audio preamplification because its 1.1 MHz unity-gain bandwidth and 0.6 V/us slew rate support audio-frequency waveforms while the two channels can handle left and right signals independently. Its internally compensated architecture simplifies the gain stage and reduces the need for external compensation components. The 100 dB DC voltage gain provides ample open-loop gain for closed-loop audio amplification. Designers should still confirm output swing against the selected supply voltage and evaluate distortion and noise against the manufacturer datasheet limits.
推荐
Industrial Sensor Conditioning
The LM258YDT is suitable for conditioning low-bandwidth industrial sensor signals when the source impedance is high and input bias current matters. Its published input bias current of 20 nA helps minimize bias-induced error, while the dual package can amplify or buffer two related channels. The 1.1 MHz unity-gain bandwidth covers many process-control and instrumentation signals. Verify the sensor output range against the LM258YDT common-mode and supply limits, and check the automotive temperature qualification required by the target installation.
推荐
Active Filtering
The LM258YDT can implement active low-pass, high-pass, or notch-filter sections because the internally compensated dual amplifier provides two signal-processing channels in one 8-SOIC package. A 1.1 MHz unity-gain bandwidth supports filter designs well above conventional audio baseband frequencies, while 100 dB DC gain helps reduce closed-loop gain error. Component tolerances and amplifier stability requirements must be considered for higher-Q filters. Confirm the datasheet gain-bandwidth, noise, and output-swing curves against the selected filter topology.
推荐
Voltage Buffer
The LM258YDT works well as a dual voltage buffer when a higher-impedance source must drive a downstream measurement or control stage. Internally frequency compensation supports unity-gain voltage-follower use without an external compensation network, and the 0.6 V/us slew rate limits large-signal behavior during rapid input transitions. Both channels can buffer complementary control signals in a compact 8-SOIC footprint. Validate the source and sink current capabilities, output swing, capacitive-load stability, and input common-mode range for the actual operating conditions.
推荐
Motor and Control Signal Conditioning
The LM258YDT can condition low-frequency position, current, or feedback signals in industrial and automotive control systems. Its 100 dB DC gain is useful when a control-loop amplifier needs high closed-loop accuracy, while the 1.1 MHz unity-gain bandwidth can accommodate feedback signals with moderate frequency content. The dual configuration can process command and feedback channels independently. Because switching nodes and motor returns can create large transients, use careful grounding, isolation, filtering, and common-mode analysis before connecting the amplifier.
推荐
Portable Instrumentation
The LM258YDT is appropriate for compact, low-power instrumentation because it combines two amplifier channels in an 8-SOIC package and is specified as having very low supply current per amplifier, essentially independent of supply voltage. The 20 nA input bias current is favorable for high-impedance probes, and the 1.1 MHz bandwidth supports measurements beyond the slowest DC regime. A portable design should still examine supply range, shutdown strategy, quiescent current, temperature rise, and battery-voltage variation before selecting operating points and passive components.
推荐
推荐产品汇总
工程参考数据: LM258YDT ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | LM258DT | LM258ADT | LM258AYDT | LM358DT | LM358YDT |
|---|---|---|---|---|---|---|
| Package | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC |
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics |
| Amplifier Channels | 2 | 2 | 2 | 2 | 2 | 2 |
| Frequency Compensation | Internal | Internal | Internal | Internal | Internal | Internal |
| Automotive Ordering Option | Yes | No Y ordering designation | No Y ordering designation | Yes | No Y ordering designation | Yes |
| Mounting Type | Surface mount | Surface mount | Surface mount | Surface mount | Surface mount | Surface mount |
关键差异点
- Combines two amplifier channels with automotive-oriented ordering (对比 LM258DT)
- Higher nominal bandwidth than the LM358 alternatives (对比 LM358DT)
- Faster nominal slew rate than the LM358 alternatives (对比 LM358YDT)
设计说明
Place the supply bypass capacitor immediately adjacent to the LM258YDT supply pins and provide a low-impedance return path to the device ground. Keep input and output traces short, particularly around high-gain feedback loops, and avoid routing sensitive inputs beneath digital or switching nodes. Confirm the physical pin-1 orientation and SOIC land pattern against the manufacturer package drawing before layout release.
Keep the LM258YDT feedback components close to the amplifier pins and minimize the feedback-loop area to reduce susceptibility to parasitic capacitance and noise pickup. The device is internally frequency compensated for common configurations, but unusually high noise gain, large capacitive loads, or long feedback traces can still affect stability. Use the manufacturer stability and capacitive-load guidance when the operating conditions differ from the standard test setup.
Check the selected supply voltage against the LM258YDT operating range and verify that every signal remains within the usable input common-mode range. Also confirm output swing at the intended load because a low-power amplifier can approach its output limits before reaching the nominal supply rail. Decoupling capacitance, stability, and maximum output current should be evaluated together rather than treated as independent constraints.
Do not assume that every LM358-family ordering option is an automatic substitute for the LM258YDT. Although related devices can share an 8-SOIC footprint, DC offset, input bias current, common-mode range, output swing, temperature grade, and automotive qualification can differ. Compare the manufacturer datasheet for every production substitution and perform stability, offset, output-swing, and thermal checks on the assembled board.
合规信息
The product listing identifies the LM258YDT as automotive grade. Formal RoHS, REACH, AEC-Q100 qualification, lead-free, halogen-free, and conflict-minerals statements are not established by the available component documentation.