LM324WDT - Low-Power Quad Op Amp | STMicroelectronics | Industrial
MPN: LM324WDT ✗ Cuối đờiLM324WDT Tóm tắt
A quad operational amplifier is a semiconductor containing four independent high-gain amplifier sections in one package. An operational amplifier compares voltages applied to its inverting and non-inverting inputs and drives its output according to the difference between them. The quad format belongs to the broader analog-amplifier hierarchy and can replace four separate single-channel amplifier packages when the channels do not require isolated supplies.
The LM324WDT's principal features include four amplifier circuits, a push-pull output stage, low input bias current, low power consumption, and high open-loop voltage gain. The 3 V to 32 V operating-voltage range allows operation from regulated 5 V systems through higher industrial supply rails. Operating all four channels from one package also reduces board area, although common power and ground connections require careful layout planning.
Internally, the device uses the widely established LM324 universal standard amplifier architecture with integrated phase-compensation capacitors. This architecture prioritizes low cost, broad supply-voltage compatibility, and ease of general-purpose analog design rather than the very low offset, low noise, high speed, or rail-to-rail output characteristics found in precision amplifiers. The push-pull output structure supports bidirectional output drive within the available supply limits.
Typical uses include low-frequency sensor amplification, transducer signal conditioning, current-to-voltage conversion, voltage comparison, basic active filtering, control-loop amplification, and general instrumentation. The four channels can process related signals or perform independent functions such as buffering, error amplification, summing, and threshold detection. For battery-operated or power-sensitive systems, the low-power architecture is especially useful when the required signal bandwidth remains modest.
For stable operation, follow the manufacturer datasheet when selecting supply bypassing capacitors, handling input and output signals near the supply rails, and accommodating output-current limits. Decoupling capacitors should be placed close to the supply pins, and unused amplifier inputs should be biased to a defined potential rather than left floating. The wide input and output common-mode limitations of the LM324 family should be checked before using it in high-side sensing or rail-to-rail signal chains.
This page combines exact catalog information, pin-level implementation guidance, same-package replacement choices, and application-oriented design notes. It helps engineers determine whether the LM324WDT's four-channel, 3 V to 32 V general-purpose architecture is appropriate for a new design or an existing 14-SO PCB.
Bộ thay thế dễ dàng lắp đặt cho LM324WDT — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với LM324WDT (cùng hình factor và footprint) — khác nhau ở Package, Amplifier Type, Input Offset Voltage, Supply Voltage Range, Operating Temperature Range.
LM324DT
✅ Drop-In ⚠️ Thông số chưa được xác minh✗ Hết hàng
$0.0827 / Đơn vị
Xem tài liệu →LM324QT
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →LM324DR
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →LM324ADR
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →LM324BAIDR
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →LM324WDT Tỷ lệ tối đa & tính chất điện
| Amplifier Type | General-purpose operational amplifier |
| Number of Amplifier Channels | 4 channels |
| Kiểu đầu ra | Push-pull |
| Supply Voltage Range | 3 V to 32 V |
| Architecture | Quad operational amplifier |
| Input Bias Current | Low input bias current |
| Power Consumption | Low power consumption |
| Open-Loop Voltage Gain | High gain |
| Phase Compensation | Integrated capacitors |
| Hộp | 14-SO SOIC |
| Số chân | 14 pins |
| Kiểu lắp đặt | Surface mount |
| Product Type | Low-power quad operational amplifier |
| Compliance | RoHS and REACH status not stated |
| Automotive Qualification | AEC-Q100 status not stated |
Cấu hình chân LM324WDT
| Chân 1 | OUT1 — Amplifier 1 output |
| Chân 2 | -IN1 — Amplifier 1 inverting input |
| Chân 3 | +IN1 — Amplifier 1 non-inverting input |
| Chân 4 | V- — Negative supply or ground connection |
| Chân 5 | +IN2 — Amplifier 2 non-inverting input |
| Chân 6 | -IN2 — Amplifier 2 inverting input |
| Chân 7 | OUT2 — Amplifier 2 output |
| Chân 8 | OUT3 — Amplifier 3 output |
| Chân 9 | -IN3 — Amplifier 3 inverting input |
| Chân 10 | +IN3 — Amplifier 3 non-inverting input |
| Chân 11 | V+ — Positive supply connection |
| Chân 12 | -IN4 — Amplifier 4 inverting input |
| Chân 13 | +IN4 — Amplifier 4 non-inverting input |
| Chân 14 | OUT4 — Amplifier 4 output |
Ứng dụng tiêu biểu
LM324WDT phù hợp cho 6 Áp dụngs: Industrial Sensor Signal Conditioning, Current-to-Voltage Conversion, Control-System Error Amplifier, Audio and Communication Buffering, Active Filtering and Summing, Battery-Powered Portable Instrumentation.
Industrial Sensor Signal Conditioning
The LM324WDT is well suited to low-frequency industrial sensor conditioning because four low-power amplifier channels can buffer, scale, and offset several related sensor signals on one board. Its 3 V to 32 V supply range supports 5 V instrumentation as well as higher-voltage industrial rails. Use one channel for the input amplifier and others for offset correction or active filtering. The designer must keep signals inside the LM324's specified common-mode and output-swing ranges, because the device is not rail-to-rail at input or output.
Được đề xuất
Current-to-Voltage Conversion
The LM324WDT can implement four current-to-voltage conversion or transimpedance stages when the required signal bandwidth is modest. Low input bias current helps reduce error when working with high-impedance sensors, while the four-channel architecture consolidates multiple measurements into one 14-SO package. Place the amplifier close to the sensing node to minimize leakage and parasitic capacitance, and add compensation appropriate to the feedback network. Verify stability with the intended source capacitance rather than relying only on nominal bandwidth.
Được đề xuất
Control-System Error Amplifier
The LM324WDT provides four low-power channels for error amplification, actuator feedback, threshold comparison, and auxiliary control functions in basic analog control systems. Its high open-loop gain supports closed-loop error correction, while the 3 V to 32 V supply range permits operation from low-voltage controls to higher-voltage industrial buses. Four channels reduce footprint compared with separate packages, but common ground and supply routing can couple noise between channels. Separate sensitive feedback routing from power-intensive actuator paths and use local supply bypassing.
Được đề xuất
Audio and Communication Buffering
The LM324WDT can serve as a general-purpose buffer or gain stage in line-level audio, communications, and other low-frequency analog systems. Its push-pull output stage drives the output in both directions more effectively than an open-collector implementation, while the four-channel format supports repeated buffering or mixing functions. The device is best suited to signals that remain within its input and output swing limits. Confirm noise, bandwidth, and slew-rate requirements for the highest-frequency channel before using it in precision audio paths.
Được đề xuất
Active Filtering and Summing
The LM324WDT can implement active filters, summers, difference amplifiers, and threshold detectors when low-to-moderate frequencies and simple gain settings are sufficient. Four independent channels permit a cascaded second-order filter, a summing stage, and two utility channels within one package. Passive component tolerances directly influence gain and cutoff accuracy, so use suitable resistor and capacitor tolerances for the required response. Keep the summing-node impedances balanced and avoid driving capacitive loads that could compromise stability.
Được đề xuất
Battery-Powered Portable Instrumentation
The LM324WDT is appropriate for portable, battery-powered instrumentation that needs several low-frequency analog channels and can operate from a compact supply. Its low-power operation and low input bias current help reduce consumption and loading from high-impedance sensors, while the four-channel package minimizes board area. The minimum 3 V operating supply supports energy-efficient embedded designs. For portable products, verify supply current across the complete output range and confirm that the input common-mode range includes the sensor's operating voltage.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho LM324WDT — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | LM324DT | LM324QT | LM324DR | LM324ADR | LM324BA |
|---|---|---|---|---|---|---|
| Package | 14-SO SOIC | 14-SO SOIC | 14-SO SOIC | 14-SO SOIC | 14-SO SOIC | 14-SO SOIC |
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics | Texas Instruments | Texas Instruments | Texas Instruments |
| Amplifier Channels | 4 channels | 4 channels | 4 channels | 4 channels | 4 channels | 4 channels |
| Product Category | General-purpose operational amplifier | General-purpose operational amplifier | General-purpose operational amplifier | General-purpose operational amplifier | General-purpose operational amplifier | General-purpose operational amplifier |
| Mounting Type | Surface mount | Surface mount | Surface mount | Surface mount | Surface mount | Surface mount |
Bảo phân biệt quan trọng
- Four independent amplifiers in one 14-SO package (vsLM324DR)
- Single-supply operation across a wide voltage range (vsLM324QT)
- Push-pull output stage for bidirectional drive (vsLM324ADR)
- Low-power and low-input-bias characteristics (vsLM324BA)
Ghi chú thiết kế
Place the required supply-decoupling capacitor immediately between pins 11 and 4, with a short and low-inductance return path. Because all four amplifiers share the same supply pins, supply disturbance can affect every channel simultaneously. Add a second local bypass capacitor when the manufacturer recommends it, and keep high-current return paths away from the sensitive input and feedback traces.
Route each non-inverting input, inverting input, and output directly to its associated circuit nodes. Keep feedback components close to pins 2, 6, 9, and 12 to minimize parasitic capacitance and feedback-loop area. Treat the exposed circuit board under the SOIC body as a thermal and electrical consideration even though this package does not use a dedicated exposed pad.
Do not assume that the 3 V to 32 V supply range also defines the usable input or output range. Check the common-mode input limits and output swing against the actual signal. Similarly, tie unused amplifier inputs to a defined bias voltage. Leaving an input floating can make the associated output unpredictable and may introduce instability into adjacent measurement circuits.
Use short traces for high-impedance sensor inputs and keep them away from supply and output routing. The LM324 family is intended primarily for low-frequency general-purpose operation, so high-gain layouts can amplify thermal noise and layout leakage. Select resistor values that avoid excessive loading and maintain feedback stability at the lowest expected signal frequency and the highest expected capacitive load.
Thông tin tuân thủ
The manufacturer listings identify the LM324WDT as a general-purpose 14-SO amplifier but do not state RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status.