MCP3422A5-E/MC - 18-Bit Dual-Input Sigma-Delta ADC | Microchip
MPN: MCP3422A5-E/MC ✓ NakahandaMCP3422A5-E/MC Ulas
An analog-to-digital converter is an integrated circuit that converts an analog input voltage into a numeric value for processing, storage, display, or control. The MCP3422 belongs to the ADC hierarchy and uses a sigma-delta architecture, which is especially useful for low-frequency precision measurements where narrow bandwidth is more important than high-rate waveform capture. Its two analog input channels allow one converter to serve multiple sensors or measurement nodes.
The MCP3422A5-E/MC provides 18-bit resolution, dual analog inputs, and a 3.75 Hz conversion rate. These characteristics suit temperature, pressure, load-cell, chemical-sensor, and slow industrial process measurements where a stable input signal is sampled over time. Its operating supply range of 2.7 V to 5.5 V supports both 3.3 V and 5 V system architectures, while the I2C interface reduces the number of signal connections required on a compact circuit board.
Sigma-delta conversion uses continuous-time modulation and digital filtering to reduce quantization noise near the signal bandwidth. This makes the architecture appropriate for extracting relatively small changes from sensor outputs without requiring a high-speed successive-approximation ADC. The onboard reference supports a self-contained measurement chain, while external analog conditioning remains important for protecting the inputs and scaling signals into the converter’s measurement range.
Typical applications include battery-powered environmental sensors, industrial pressure transmitters, precision temperature instrumentation, laboratory data-acquisition modules, and low-rate weighing systems. The 2 mm by 3 mm DFN package supports compact sensor assemblies, and the dual-input arrangement can reduce component count when two related analog signals must be measured.
PCB design should prioritize a quiet reference return, short analog traces, and placement of input filtering close to the MCP3422A5-E/MC. Because this is a low-rate precision ADC, switching circuitry and high-current digital paths should be kept away from the analog pins to avoid degrading the measured signal.
This product page combines the exact MCP3422A5-E/MC electrical identity, package information, drop-in family alternatives, comparison data, and practical design guidance to support component selection, PCB planning, and sourcing decisions.
Mga alternatibo na pwedeng ilagay na MCP3422A5-E/MC — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.
Variante sa Seri na ito
Katulad na modelo sa serye na katugma sa pagpasok MCP3422A5-E/MC (parehas na form factor at footprint) — pagkakaiba sa Package, Digital Interface, Conversion Rate, Differential Input Range, Resolution.
MCP3422A0-E/MC
✅ Drop-InMagkontak para sa presyo
Tingnan ang Datasheet →MCP3422A0T-E/MC
✅ Drop-In📋 Alternatibo na Reference (hindi sa katalogo)
MCP3422A2-E/MC
✅ Drop-InMagkontak para sa presyo
Tingnan ang Datasheet →MCP3422A3-E/MC
✅ Drop-InMagkontak para sa presyo
Tingnan ang Datasheet →MCP3422A5T-E/MC
✅ Drop-In📋 Alternatibo na Reference (hindi sa katalogo)
MCP3422A5-E/MC Mga Pinakamataas na Rating at Electrical Characteristics
| ADC Type | Sigma-delta analog-to-digital converter |
| Pangangasiwaan | 18 bit |
| Analog Input Channels | 2 inputs |
| Conversion Rate | 3.75 samples/s |
| Supply Voltage Range | 2.7 V to 5.5 V |
| Digital Interface | I2C |
| Internal Reference | Onboard voltage reference |
| Packhaging | 8-DFN, 2 mm x 3 mm |
| Bilang ng Pin | 8 pins |
| Uri ng Pagpapasok | Surface mount |
| Tindminan RoHS | RoHS |
Gabay sa Pin Configuration ng MCP3422A5-E/MC 8-dfn, 2 mm x 3 mm
Pin configuration para sa MCP3422A5-E/MC (8-dfn, 2 mm x 3 mm package). Ang analog component na ito ay may input, output, at power supply pins. Sumangguni sa datasheet ng manufacturer para sa offset null, compensation, at enable pin configurations. Perpekto para sa signal conditioning at amplifier circuits.
Wala ng detalyadong pinout data na magagamit para sa MCP3422A5-E/MC.
Sumangguni sa datasheet para sa buong pin configuration.
Tipikal na mga Gamit
MCP3422A5-E/MC ay nararapat para sa 6 aplikasyons: Precision Temperature Sensing, Industrial Pressure Monitoring, Load Cell and Weighing Systems, Chemical and Environmental Sensors, Battery-Powered Instrumentation, Laboratory Data Acquisition.
Precision Temperature Sensing
The MCP3422A5-E/MC fits low-rate temperature measurement because its 18-bit sigma-delta converter provides high numerical resolution while operating at 3.75 samples/s. Two analog inputs can monitor two temperature channels or one sensor plus a reference channel. The device is commonly placed behind an RTD, thermocouple, or resistive sensor front end, with filtering close to the analog pins. Its onboard reference and I2C interface simplify acquisition, although sensor excitation and input-scaling circuitry remain separate from the ADC.
Inirekomenda
Industrial Pressure Monitoring
The MCP3422A5-E/MC is appropriate for slow industrial pressure signals that require more numerical resolution than an 8-bit or 12-bit converter provides. At 3.75 samples/s, the ADC can continuously update a filtered pressure measurement while communicating over I2C to a controller. The dual inputs can serve a pressure sensor and a diagnostic channel. A ratiometric bridge, protection network, and analog filter should be designed to preserve the converter’s effective noise performance.
Inirekomenda
Load Cell and Weighing Systems
The 18-bit resolution of the MCP3422A5-E/MC is useful for weighing platforms and load-cell front ends where a small differential voltage represents a relatively small mechanical force. The low 3.75 samples/s conversion rate suits static or slowly changing loads rather than dynamic vibration analysis. An instrumentation-amplifier stage, excitation source, and differential filtering network should precede the ADC, while the I2C interface connects the converter to a display or system controller.
Inirekomenda
Chemical and Environmental Sensors
The MCP3422A5-E/MC can digitize slow outputs from electrochemical, gas, conductivity, and environmental sensors without the complexity of a high-rate acquisition system. Its dual inputs permit monitoring a sensing electrode and a reference or auxiliary channel, while 18-bit resolution supports fine-grained numerical measurement. Because these sensors can present high source impedance or millivolt-level signals, the design should use a low-noise amplifier and guarded, filtered routing before conversion.
Inirekomenda
Battery-Powered Instrumentation
The MCP3422A5-E/MC supports compact, battery-powered instrumentation because its primary function is low-rate precision acquisition rather than continuous high-speed conversion. The 2.7 V to 5.5 V supply range accommodates common low-voltage rails, and the I2C interface allows measured data to be transferred efficiently to a microcontroller or wireless controller. Duty-cycling the converter and peripheral circuitry can help control average system power when the measured quantity changes slowly.
Inirekomenda
Laboratory Data Acquisition
The MCP3422A5-E/MC is useful in laboratory measurement systems that monitor slowly varying voltages and value high-resolution readings over a narrow bandwidth. Two inputs allow simultaneous use for a DUT measurement and a calibration or monitor channel. The 18-bit resolution and onboard reference simplify the measurement chain, while I2C supports connection to embedded controllers. For faster transient capture, designers should select an ADC with a higher conversion rate rather than accelerating this sigma-delta device beyond its intended operating mode.
Inirekomenda
Buod ng mga Inirekomendang Produkto
Impormasyon ng Talumpati sa Engineering for MCP3422A5-E/MC — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.
Paunawang Hanapin
Ikabit sa Mga Alternatibo
| Parametro | Ito ang Producto | MCP3422A0-E/MC | MCP3422A0T-E/MC | MCP3422A2-E/MC | MCP3422A3-E/MC | MCP3422A5T-E/MC |
|---|---|---|---|---|---|---|
| Package | 8-DFN (2x3) | 8-DFN (2x3) | 8-DFN (2x3) | 8-DFN (2x3) | 8-DFN (2x3) | 8-DFN (2x3) |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Resolution | 18 bit | 18 bit | 18 bit | 18 bit | 18 bit | 18 bit |
| Converter Architecture | Sigma-delta | Sigma-delta | Sigma-delta | Sigma-delta | Sigma-delta | Sigma-delta |
| Supply Voltage Range | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 2.7 V to 5.5 V |
| Digital Interface | I2C | I2C | I2C | I2C | I2C | I2C |
Pangunahing mga Pagkakaiba
- High numerical resolution in a compact dual-input converter (kumpara saMCP3422A3-E/MC)
- Dual analog inputs reduce measurement-channel component count (kumpara saMCP3422A0-E/MC)
- Compact 8-DFN footprint supports space-constrained sensor assemblies (kumpara saMCP3422A2-E/MC)
- Onboard reference supports a compact measurement architecture (kumpara saMCP3422A5T-E/MC)
Talaan ng Disenyo
Place the MCP3422A5-E/MC close to the sensor front end and route both analog inputs as short, matched paths. Keep the exposed pad connection consistent with the manufacturer land-pattern guidance. Separate the analog input region from I2C clock and data routing where practical, and provide a quiet ground return for the converter and reference circuitry to minimize coupling from digital switching activity.
Use the input-network topology and capacitor values specified in the manufacturer datasheet for the selected source impedance. Sensor signals are often small and slow, making leakage, offset, and resistor mismatch more important than wideband timing. Verify the source impedance against the converter’s sampling network before adding large filter capacitors, because excessive capacitance can affect settling and conversion accuracy.
Do not treat the 18-bit resolution as a guarantee of 18 bits of useful accuracy. Overall error also depends on the reference, analog front end, noise, calibration, layout, and operating mode. Confirm the differential or single-ended input configuration, conversion mode, digital filter settling time, and output data format in the manufacturer datasheet before writing firmware or calculating scaling.
Decouple the 2.7 V to 5.5 V supply close to the device and connect the exposed pad as directed by the package drawing. Keep sensor excitation currents and regulator switching loops away from the analog return path. For battery-powered equipment, account for both the converter operating current and the external front end because analog amplifiers, references, and filters may dominate the total system demand.
Impormasyon ng Pagsunod sa Kautusan
The verified product listing identifies the MCP3422A5-E/MC as RoHS compliant. No explicit REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declaration was identified for this exact ordering code.