Microchip Technology

PIC10F202-E/MC - 8-Bit 4MHz Flash MCU | Microchip

MPN: PIC10F202-E/MC ✓ Nakahanda
6 pins Package 4 MHz Speed 768 bytes (512 x 12 bits) Memory
MOQ: 1 |

PIC10F202-E/MC Ulas

The Microchip Technology PIC10F202-E/MC is a low-cost, fully static, 8-bit Flash-based CMOS microcontroller with a 4 MHz operating speed, 768 bytes of Flash program memory, 24 bytes of RAM, and four general-purpose I/O pins. The PIC10F202-E/MC uses a compact six-pin surface-mount package suitable for space-constrained control systems.

A microcontroller integrates a processor core, nonvolatile program memory, data memory, input/output ports, and clocking into one integrated circuit. The PIC10F202 belongs to the PIC10F family of small RISC-based embedded controllers, a subset of 8-bit microcontrollers used for compact sensing, control, and logic functions. Its fully static architecture allows operation without a continuous system clock when the processor is idle.

The PIC core uses 33 single-word instructions. Most instructions execute in one cycle, corresponding to 1 microsecond at the 4 MHz operating speed, while program branches require two cycles. The 12-bit instruction architecture provides efficient program encoding, with the PIC10F202 implementing 512 program words of 12 bits each, equivalent to 768 bytes of Flash storage. Additional useful resources include 24 bytes of RAM and four I/O pins.

This combination makes the PIC10F202-E/MC appropriate for simple embedded products that need nonvolatile firmware, modest processing capacity, and a very small board footprint. Applications include relay or lamp controllers, compact keypads, simple sensor interfaces, auxiliary control modules, fan controllers, and low-cost household appliances. The Flash architecture supports in-system programming, allowing firmware to be updated without replacing the device.

The device belongs to the broader hierarchy of RISC microcontroller, embedded controller, 8-bit MCU, and semiconductor. Its compact pin count reduces board area, but careful pin budgeting is important because the I/O pins also support device functions. Before finalizing a design, assign pins by consulting the manufacturer datasheet pin-description table and verify that every required control, serial, analog, and debug function has an available pin.

For a new layout, place the decoupling capacitor immediately beside the supply and ground pins, keep programming and communication traces short, and reserve adequate board area for the six-pin package footprint. Firmware should account for instruction timing, reset behavior, configuration-word settings, and any brownout conditions. Existing software developed for the PIC10F202 family can simplify migration when the same MCU, package, and core architecture are retained.

This page combines the device architecture, programming resources, package constraints, practical application guidance, and same-family drop-in comparisons. These engineering details help shorten design evaluation while keeping the final pin assignment and firmware validation tied to the Microchip datasheet.

Mga alternatibo na pwedeng ilagay na PIC10F202-E/MC — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.

Variante sa Seri na ito

Katulad na modelo sa serye na katugma sa pagpasok PIC10F202-E/MC (parehas na form factor at footprint) — pagkakaiba sa Package, Instruction Set, Architecture, Program Memory (Flash), Timers.

Microchip Technology
Package: 8-pin DFN (2x3 mm)
Instruction Set: 33 single-word/single-cycle instructions
Program Memory (Flash): 384 bytes (256 x 12-bit words)
Microchip Technology
Package: 8-DFN, 2 x 3 mm
Instruction Set: 33 single-word, single-cycle instructions
Architecture: PIC10 8-bit RISC
Microchip Technology
Package: 8-VFDFN Exposed Pad (MC)
Program Memory (Flash): 384 bytes (256 x 12)
Timers: TMR0 (8-bit with 8-bit prescaler)
Microchip Technology
Package: 8-DFN (2 x 3 mm)
Architecture: Fully static
Microchip Technology
Package: 8-pin DFN (2x3 mm) with exposed pad
Instruction Set: 33 single-word instructions, 12-bit wide
Architecture: 8-bit RISC (Harvard)

PIC10F200-E/MC

✅ Drop-In ⚠️ Mga Talaan Hindi Naiwerikmo
Microchip Technology
📦 6-pin -/MC package
8-bit PIC RISC · 384 bytes (256 x 12-bit words) · 16 bytes · 4 MHz · 33 single-word/single-cycle instructions · 12-bit · 4 (bidirectional GPIO) · 1 x 8-bit (TMR0) with 8-bit prescaler

Magkontak para sa presyo

Tingnan ang Datasheet →

PIC10F204-E/MC

✅ Drop-In ⚠️ Mga Talaan Hindi Naiwerikmo
Microchip Technology
📦 6-pin -/MC package
8-bit PIC RISC · 384 bytes (256 x 12) · 16 bytes · 4 (3 I/O + 1 input-only) · 4 MHz · 33 single-word instructions · 1 us at 4 MHz · 2.0 V to 5.5 V

Magkontak para sa presyo

Tingnan ang Datasheet →

PIC10F206-E/MC

✅ Drop-In ⚠️ Mga Talaan Hindi Naiwerikmo
Microchip Technology
📦 6-pin -/MC package
8-bit Flash-based CMOS microcontroller · RISC · 33 single-word instructions · 4 MHz · 768 bytes Flash (512 x 12 words) · 24 bytes RAM · 4 pins · 2 V to 5.5 V

Magkontak para sa presyo

Tingnan ang Datasheet →

PIC10F202-I/MC

✅ Drop-In ⚠️ Mga Talaan Hindi Naiwerikmo
Microchip Technology
📦 6-pin -/MC package
8-Bit RISC Flash Microcontroller · 4 MHz · 768 bytes Flash (512 x 12 bits) · 24 bytes SRAM · 4 pins · PIC10 8-bit RISC · 33 single-word, single-cycle instructions · 1 cycle at 4 MHz (0.25 us)

Magkontak para sa presyo

Tingnan ang Datasheet →

PIC10F202T-E/MC

✅ Drop-In ⚠️ Mga Talaan Hindi Naiwerikmo
📦 6-pin -/MC package
Retains the same PIC10F202 electrical architecture and 6-pin -/MC package, with a different ordering suffix and packaging or temperature designation; verify the orderable-code details before substitution.

📋 Alternatibo na Reference (hindi sa katalogo)

PIC10F202-E/MC Mga Pinakamataas na Rating at Electrical Characteristics

Product Type 8-bit Flash-based CMOS microcontroller
CPU Architecture RISC
Maksimum na Taktiko ng Oras 4 MHz
Instruction Set 33 single-word instructions
Typical Instruction Cycle Time 1 us at 4 MHz
Program Branch Cycle Count 2 cycles
Flash Program Memory 768 bytes (512 x 12 bits)
Program Memory Architecture 10-bit program counter
RAM 24 bytes
General-Purpose I/O Pins 4 pins
Instruction Width 12 bits
Architecture Type Fully static
Program Memory Type Flash
Process Technology CMOS
Package Pin Count 6 pins
Uri ng Pagpapasok Surface mount

Gabay sa Pin Configuration ng PIC10F202-E/MC 6 pins

Pin configuration para sa PIC10F202-E/MC (6 pins package). Kasama sa digital IC na ito ang GPIO, mga communication interface (UART, SPI, I2C), at mga power pin. Sumangguni sa datasheet ng manufacturer para sa mga alternatibong function ng pin at mga opsyon sa configuration. Mahalaga para sa disenyo ng embedded system at PCB layout.

Pinout diagram ng 6 pins package para sa PIC10F202-E/MC

Wala ng detalyadong pinout data na magagamit para sa PIC10F202-E/MC.

Sumangguni sa datasheet para sa buong pin configuration.

Tipikal na mga Gamit

PIC10F202-E/MC ay nararapat para sa 6 aplikasyons: LED Lighting Controller, Compact Relay Control Module, Small Sensor Interface, Household Appliance Controller, Fan and Small Motor Controller, Programmable Logic Controller.

💡

LED Lighting Controller

The PIC10F202-E/MC is suitable for compact LED lighting controls because it provides four I/O pins, a 4 MHz RISC core, and 768 bytes of Flash in a six-pin package. A microcontroller-based design can debounce switches, apply lighting levels, and implement timed operating profiles without requiring a larger processor. The typical implementation uses GPIO outputs to drive transistor or LED-driver stages while limiting current through the MCU pins. Because only 512 program words are physically implemented, the firmware should use compact state-machine logic and reserve memory for fault handling. A 1 microsecond instruction cycle allows responsive input polling, although exact timing must include branch cycles, peripheral latency, and configuration-bit settings from the Microchip PIC10F200/202/204/206 Data Sheet 40001239F.

🏭

Compact Relay Control Module

PIC10F202-E/MC can act as the control element in a small relay-driver module for appliances, HVAC accessories, or industrial auxiliary equipment. Its four I/O pins are sufficient for limited switch inputs and relay-control outputs when each signal has a defined electrical function. The fully static, Flash-based architecture supports low-power standby operation between state changes and allows firmware updates without replacing the MCU. In implementation, the relay coil should be driven by a transistor or driver circuit so the microcontroller pin current remains within its specified limits, while flyback protection is placed across the inductive load. The compact six-pin package reduces board area, but the designer must plan pin multiplexing carefully and use the manufacturer pin-description table when assigning MCU, programming, and control functions.

🧩

Small Sensor Interface

The PIC10F202-E/MC is useful for a compact sensor interface that converts a small number of discrete inputs into a control or alarm output. Four I/O pins can accommodate digital sensors, threshold inputs, or status signals, while the 4 MHz core supports sampling routines and basic filtering. For analog measurement, the selected PIC10F202 variant's available analog-capable pins must be confirmed in the six-pin package pin table before the PCB is released. Firmware can implement hysteresis, debounce counters, and threshold logic while occupying less than the available 512 implemented 12-bit program words. Because the MCU has only 24 bytes of RAM, measurements and state variables should be compact, and application code must avoid relying on stack depth or peripheral features not present in the selected device variant.

🔧

Household Appliance Controller

PIC10F202-E/MC fits low-cost household appliance subassemblies that need local logic, persistent settings, and a minimal footprint. Typical tasks include button decoding, motor-step sequencing, timer management, and safety-state handling. The 33-instruction RISC core executes most instructions in one cycle at 4 MHz, allowing the controller to service multiple inputs without a large clock tree. Flash memory preserves operating parameters between power cycles, while the 24-byte RAM is sufficient for compact state variables. A practical design should keep the power conversion stage physically separate from sensitive MCU routing, provide local decoupling, and confirm the available pins before allocating functions. Firmware size must remain within 512 implemented program words, making efficient tables and branch structure important for feature-rich appliance products.

⚡

Fan and Small Motor Controller

The PIC10F202-E/MC can control a small fan or low-current motor subsystem through external transistor circuitry, making it suitable for compact thermal-management modules. Its GPIO resources can accept speed commands or sensor inputs, while the 4 MHz processing rate supports basic closed-loop timing and fault counting. The MCU should not drive an inductive load directly; a suitably rated driver and protection network are required. The small Flash footprint can store a lookup table for speed levels, timing profiles, and fault codes, while the fully static architecture supports efficient idle periods between commands. Because available RAM is limited to 24 bytes, control loops should use minimal state storage, and the firmware must include startup delays, lockout behavior, and a defined output-off state after reset to prevent unintended motion.

⚙️

Programmable Logic Controller

PIC10F202-E/MC can serve as a compact programmable logic controller for simple discrete automation, providing sequenced outputs and configurable input behavior in a six-pin package. Its Flash-based firmware permits repeatable operation, and the four I/O pins are suited to small relay, indicator, and interlock arrangements. A useful implementation places the MCU beside screw terminals or a compact connector, with external buffers for loads and interface circuits for long wiring. The 512 implemented program words are sufficient for compact ladder-like state logic, timers, and diagnostics but not extensive communication middleware. Firmware should prioritize deterministic execution, include safe output states during reset, and test every configuration-word setting. The -/MC footprint and pin allocation should be validated against the package drawing before committing the PCB layout.

What are the key specifications of PIC10F202-E/MC that engineers should know?
The PIC10F202-E/MC is an 8-bit, RISC-based, fully static Flash microcontroller operating at up to 4 MHz, with 768 bytes of program Flash, 24 bytes of RAM, four I/O pins, and a six-pin surface-mount package. According to the Microchip PIC10F200/202/204/206 Data Sheet 40001239F, its 33 single-word instructions normally execute in one cycle, while program branches require two cycles.
Where can I download the PIC10F202 datasheet PDF?
The official PIC10F202 family datasheet can be downloaded from the Microchip Technology document link for 40001239F.pdf. That document covers the PIC10F200, PIC10F202, PIC10F204, and PIC10F206 devices and includes package identification, program-memory organization, electrical characteristics, and the information needed to select the correct ordering code.
Where can I find the PIC10F202 pinout?
The PIC10F202 pinout is published in the package and pin-description sections of the Microchip PIC10F200/202/204/206 Data Sheet 40001239F.pdf. Use the diagram corresponding to the -/MC package rather than another six-pin package, because SOT-23, QFN, and other six-pin options can use different physical lead arrangements even though their logical device functions are related.
How do I program the PIC10F202?
The PIC10F202 is programmed through its Flash program memory using the programming interface specified by Microchip. The device uses 512 physically implemented 12-bit program words, with the first 512 words of the 1024-word address space physically populated. Confirm connector voltage, programming protocol, configuration-word settings, and erase or write timing against the Microchip programming specifications before production programming.
Is the PIC10F202 suitable for low-power embedded control?
The PIC10F202 is suitable for compact control tasks because it is a fully static Flash-based MCU and provides four I/O pins within a six-pin package. Its 4 MHz maximum speed supports quick peripheral servicing, while static operation permits the CPU to remain idle between events. Exact sleep-mode current, wake-up time, and operating voltage must be checked in the manufacturer electrical characteristics before setting a power budget.
What can replace the PIC10F202-E/MC?
A replacement should preserve the six-pin -/MC footprint, pin functions, Flash organization, RAM capacity, and clock architecture. PIC10F200, PIC10F204, and PIC10F206 devices are same-brand family alternatives with related hardware, but their implemented Flash capacity differs. Confirm the exact memory map and configuration requirements in 40001239F.pdf before treating any variant as a drop-in replacement.
What is the best Microchip equivalent for PIC10F202-E/MC?
The closest same-family choices are PIC10F200-E/MC, PIC10F204-E/MC, and PIC10F206-E/MC because they belong to the same six-pin PIC10F device family. The closest functional match is PIC10F202-E/MC itself; the 200, 204, and 206 variants change implemented program memory, so software, linker, and configuration-word validation are required before substitution.
PIC10F202-E/MC vs PIC10F206-E/MC - which is better for a control application?
PIC10F202-E/MC is preferable when 512 implemented 12-bit program words are sufficient, while PIC10F206-E/MC provides a larger program-memory option for more complex firmware. Both belong to the same low-cost PIC10F family and use the same core principles, but the memory footprint can affect code size, branching, table allocation, and overall firmware reliability margin.
When should I choose PIC10F202-E/MC over PIC10F200-E/MC?
Choose PIC10F202-E/MC when the application benefits from its 512 implemented 12-bit program words, which provide 768 bytes of Flash, rather than the smaller PIC10F200-E/MC memory option. The extra capacity provides more room for features such as state tables, communication routines, calibration constants, and diagnostic handling while retaining the same compact PIC10F architecture.
Is PIC10F202-E/MC suitable for an LED lighting controller?
Yes, PIC10F202-E/MC is suitable for a simple LED lighting controller when the design does not exceed its four available I/O pins and 512 implemented program words. Its 4 MHz RISC core can service switch inputs and LED outputs efficiently, and Flash permits reusable firmware. Keep transistor or LED-driver current outside the MCU pins and account for the package's limited I/O and grounding options.
Where can I buy PIC10F202-E/MC online?
Use the Request a Quote form on this page to request PIC10F202-E/MC availability, current commercial terms, and the exact -/MC ordering code. The manufacturer identifies the device under the PIC10F202 product family, and the -/MC suffix selects the specific package and temperature-grade option, which should be confirmed before quotation or purchase.
What is the price of PIC10F202-E/MC?
The current commercial price for PIC10F202-E/MC is shown through the Request a Quote form on this page. Exact pricing depends on order quantity, package code, lead time, and sourcing condition, so a quantity-specific quotation is more reliable than a generic single-unit figure. Include the complete MPN PIC10F202-E/MC in the request.
What is the lead time for PIC10F202-E/MC?
The current lead time for PIC10F202-E/MC should be confirmed through the Request a Quote form on this page. Lead time can change with order volume, production scheduling, package demand, and component traceability requirements. Provide the planned annual usage, forecast quantities, and required shipping destination so the quotation can reflect the correct supply condition.
Is PIC10F202-E/MC in stock?
Current stock for PIC10F202-E/MC is confirmed through the Request a Quote form on this page. For production planning, request both immediate availability and the replenishment lead time rather than relying on a single inventory snapshot. Include the exact package suffix -/MC and any required temperature grade in the request to prevent allocation of a different device variant.
What design constraints matter when laying out a PIC10F202-E/MC board?
The principal layout constraint is the six-pin package's limited pin budget: four I/O pins must support sensing, control, communications, and programming requirements simultaneously. Place the supply bypass capacitor close to VDD and VSS, use a short programming connector or pad arrangement, and follow the package drawing for the -/MC land pattern. According to Microchip Data Sheet 40001239F, the proper device option must be selected using the product identification system.

Impormasyon ng Talumpati sa Engineering for PIC10F202-E/MC — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.

Paunawang Hanapin

Choose PIC10F202-E/MC for compact, low-cost control products that need four I/O pins, 24 bytes of RAM, and 512 implemented 12-bit program words within a six-pin package. It is a strong fit for simple LED, relay, appliance, fan, and discrete-logic functions where nonvolatile firmware and deterministic execution matter. Select PIC10F200-E/MC only when its 256 implemented program words are sufficient, since halving the Flash capacity can constrain features and diagnostics. Evaluate PIC10F204-E/MC and PIC10F206-E/MC when their device-specific peripheral features are needed, but verify configuration words and firmware compatibility before replacing PIC10F202. Use PIC10F202-I/MC when the industrial temperature grade is appropriate and the extended-temperature option is unnecessary. For designs requiring more I/O, RAM, or application memory, move to a larger MCU rather than forcing additional functions into the limited six-pin pin budget.

Ikabit sa Mga Alternatibo

Parametro Ito ang Producto PIC10F200-E/MC PIC10F204-E/MC PIC10F206-E/MC PIC10F202-I/MC
Brand Microchip Technology Microchip Technology Microchip Technology Microchip Technology Microchip Technology
Package 6-pin -/MC package 6-pin -/MC package 6-pin -/MC package 6-pin -/MC package 6-pin -/MC package
Architecture 8-bit RISC 8-bit RISC 8-bit RISC 8-bit RISC 8-bit RISC
Maximum Clock Frequency 4 MHz 4 MHz 4 MHz 4 MHz 4 MHz
Program Memory 768 bytes (512 x 12 bits) 384 bytes (256 x 12 bits) 768 bytes (512 x 12 bits) 768 bytes (512 x 12 bits) 768 bytes (512 x 12 bits)
General-Purpose I/O 4 pins 4 pins 4 pins 4 pins 4 pins
Instruction Set 33 single-word instructions 33 single-word instructions 33 single-word instructions 33 single-word instructions 33 single-word instructions
Temperature Grade Extended temperature grade indicated by -E Extended temperature grade indicated by -E Extended temperature grade indicated by -E Extended temperature grade indicated by -E Industrial temperature grade indicated by -I

Pangunahing mga Pagkakaiba

  • Twice the implemented program memory of PIC10F200-E/MC (kumpara saPIC10F200-E/MC)
  • Retains the same core speed and instruction set as PIC10F206-E/MC (kumpara saPIC10F206-E/MC)
  • Four I/O pins in a compact six-pin package (kumpara saATTINY13A-SUR)
  • Fully static Flash operation for compact control designs (kumpara saPIC10F200-E/MC)

Talaan ng Disenyo

Treat the six-pin package as an I/O-constrained design. Before schematic capture, create a pin-budget table covering power, ground, programming, communications, inputs, and outputs. Follow the -/MC land pattern in Microchip Data Sheet 40001239F.pdf rather than reusing a SOT-23-6 footprint solely because both packages have six leads. Place the supply bypass capacitor directly across VDD and VSS, and keep the programming pads or connector accessible without mechanical changes.

Apply the exact supply limits and decoupling recommendations from the manufacturer electrical characteristics. The 4 MHz operating speed does not remove the need to sequence power rails when the board also contains sensors or external logic. Check brownout behavior, input levels during startup, and the state of all outputs at reset. Use a dedicated local VDD path and ground-return connection to prevent switching currents in the external load circuitry from creating false transitions on the MCU pins.

Do not assume that every six-pin PIC10F option has the same physical pinout or that all family members implement identical memory and peripherals. The PIC10F202 has 512 physically implemented 12-bit program words, so firmware must fit that map, and a PIC10F200 variant provides only half that program-memory capacity. Validate the linker configuration, configuration words, device selected by the build system, and reset behavior after any family substitution.

Keep high-current or switching-node paths away from the MCU and its decoupling capacitor. If an I/O drives a relay, motor, or LED driver, route that signal through the appropriate transistor and protection network, and provide a quiet return path to the power stage. Although most instructions execute in 1 microsecond at 4 MHz, deterministic firmware should not rely on that figure without accounting for two-cycle branches, interrupt latency, and peripheral timing.

The 24-byte RAM limits temporary variables, stack depth, and buffered data. Estimate the compiler-generated stack requirement for the deepest interrupt and function-call path, then leave margin rather than treating all 24 bytes as available application storage. For state machines, use program Flash for lookup tables and constants, keep frequently used state in RAM, and test interrupt nesting against the selected configuration-word settings.

Impormasyon ng Pagsunod sa Kautusan

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Walang Lead
Unknown
Walang Halogen
Unknown
Mga Conflict Mineral
Unknown

No specific RoHS, REACH, lead-free, halogen-free, conflict-minerals, or automotive qualification statement appears in the product information for this exact ordering code. AEC-Q100 status is not applicable because this ordering code is not identified as an automotive-qualified variant.

Data napatotohanan sa: 2026-11-19 — impormasyon na pinatunayan at pinapatakbo ng pangkat ng engineering ng XAIPART's component engineering team

Kaugnay na Hanapin

pic10f202 datasheet pic10f202 pinout pic10f202 programming PIC10F202-E/MC datasheet pdf PIC10F202-E/MC pinout PIC10F202-E/MC equivalent PIC10F202-E/MC replacement PIC10F202-E/MC footprint PIC10F202-E/MC price PIC10F202-E/MC stock Microchip PIC10F202-E/MC PIC10F202 vs PIC10F206-E/MC PIC10F202 six pin schematic

Mga kaugnay na Mga Komponente at mga Tuntunin

Microchip Technology PIC10F202-E/MC PIC10F202 PIC10F200-E/MC PIC10F204-E/MC PIC10F206-E/MC PIC10F202-I/MC PIC10F202T-E/MC microcontroller MCU 8-bit microcontroller RISC architecture Flash memory CMOS PIC CPU program memory RAM GPIO six-pin package surface-mount package in-system programming industrial control LED lighting controller relay control sensor interface
Mabilis na Tanggap na RFQ
Ihanda ang buong detalye — ang aming pangkalakal na koponan ay tutugon sa loob ng 24 oras
Numero ng Parte Mga Tagagawa Pakete QTY Target na Halaga Pinalawak
✓
Quote na inilabas!

Ating tumugon sa iyong email sa loob ng 24 oras

1
RFQ Naisumite
2
Received na ang Kwaliksik
3
Nai-order
4
Pagbabayad
5
Inihanda
6
Naihanda
Tingnan ang Detalye ng RFQ