PIC10F202-E/MC - 8-Bit 4MHz Flash MCU | Microchip
料号: PIC10F202-E/MC ✓ 量产中PIC10F202-E/MC 概述
A microcontroller integrates a processor core, nonvolatile program memory, data memory, input/output ports, and clocking into one integrated circuit. The PIC10F202 belongs to the PIC10F family of small RISC-based embedded controllers, a subset of 8-bit microcontrollers used for compact sensing, control, and logic functions. Its fully static architecture allows operation without a continuous system clock when the processor is idle.
The PIC core uses 33 single-word instructions. Most instructions execute in one cycle, corresponding to 1 microsecond at the 4 MHz operating speed, while program branches require two cycles. The 12-bit instruction architecture provides efficient program encoding, with the PIC10F202 implementing 512 program words of 12 bits each, equivalent to 768 bytes of Flash storage. Additional useful resources include 24 bytes of RAM and four I/O pins.
This combination makes the PIC10F202-E/MC appropriate for simple embedded products that need nonvolatile firmware, modest processing capacity, and a very small board footprint. Applications include relay or lamp controllers, compact keypads, simple sensor interfaces, auxiliary control modules, fan controllers, and low-cost household appliances. The Flash architecture supports in-system programming, allowing firmware to be updated without replacing the device.
The device belongs to the broader hierarchy of RISC microcontroller, embedded controller, 8-bit MCU, and semiconductor. Its compact pin count reduces board area, but careful pin budgeting is important because the I/O pins also support device functions. Before finalizing a design, assign pins by consulting the manufacturer datasheet pin-description table and verify that every required control, serial, analog, and debug function has an available pin.
For a new layout, place the decoupling capacitor immediately beside the supply and ground pins, keep programming and communication traces short, and reserve adequate board area for the six-pin package footprint. Firmware should account for instruction timing, reset behavior, configuration-word settings, and any brownout conditions. Existing software developed for the PIC10F202 family can simplify migration when the same MCU, package, and core architecture are retained.
This page combines the device architecture, programming resources, package constraints, practical application guidance, and same-family drop-in comparisons. These engineering details help shorten design evaluation while keeping the final pin assignment and firmware validation tied to the Microchip datasheet.
直接替换替代料: PIC10F202-E/MC ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: PIC10F202-E/MC (相同外形与封装尺寸) ——差异在于 Package, Instruction Set, Architecture, Program Memory (Flash), Timers.
PIC10F200-E/MC
✅ 直接替换 ⚠️ 规格未核验联系询价
查看数据手册 →PIC10F204-E/MC
✅ 直接替换 ⚠️ 规格未核验联系询价
查看数据手册 →PIC10F206-E/MC
✅ 直接替换 ⚠️ 规格未核验联系询价
查看数据手册 →PIC10F202-I/MC
✅ 直接替换 ⚠️ 规格未核验联系询价
查看数据手册 →PIC10F202T-E/MC
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
PIC10F202-E/MC 最大额定值与电气特性
| Product Type | 8-bit Flash-based CMOS microcontroller |
| CPU Architecture | RISC |
| 最大时钟频率 | 4 MHz |
| Instruction Set | 33 single-word instructions |
| Typical Instruction Cycle Time | 1 us at 4 MHz |
| Program Branch Cycle Count | 2 cycles |
| Flash Program Memory | 768 bytes (512 x 12 bits) |
| Program Memory Architecture | 10-bit program counter |
| RAM | 24 bytes |
| General-Purpose I/O Pins | 4 pins |
| Instruction Width | 12 bits |
| Architecture Type | Fully static |
| Program Memory Type | Flash |
| Process Technology | CMOS |
| Package Pin Count | 6 pins |
| 安装类型 | Surface mount |
PIC10F202-E/MC 6 pins 引脚配置指南
PIC10F202-E/MC(6 pins 封装)的引脚配置。 该数字 IC 包含 GPIO、通信接口(UART、SPI、I2C)和电源引脚。请参阅制造商数据手册以了解复用引脚功能和配置选项。对嵌入式系统设计和 PCB 布局至关重要。
暂无详细引脚数据: PIC10F202-E/MC.
请参阅 数据手册 以查看完整引脚配置。
典型应用
PIC10F202-E/MC 适用于 6 应用s: LED Lighting Controller, Compact Relay Control Module, Small Sensor Interface, Household Appliance Controller, Fan and Small Motor Controller, Programmable Logic Controller.
LED Lighting Controller
The PIC10F202-E/MC is suitable for compact LED lighting controls because it provides four I/O pins, a 4 MHz RISC core, and 768 bytes of Flash in a six-pin package. A microcontroller-based design can debounce switches, apply lighting levels, and implement timed operating profiles without requiring a larger processor. The typical implementation uses GPIO outputs to drive transistor or LED-driver stages while limiting current through the MCU pins. Because only 512 program words are physically implemented, the firmware should use compact state-machine logic and reserve memory for fault handling. A 1 microsecond instruction cycle allows responsive input polling, although exact timing must include branch cycles, peripheral latency, and configuration-bit settings from the Microchip PIC10F200/202/204/206 Data Sheet 40001239F.
推荐
Compact Relay Control Module
PIC10F202-E/MC can act as the control element in a small relay-driver module for appliances, HVAC accessories, or industrial auxiliary equipment. Its four I/O pins are sufficient for limited switch inputs and relay-control outputs when each signal has a defined electrical function. The fully static, Flash-based architecture supports low-power standby operation between state changes and allows firmware updates without replacing the MCU. In implementation, the relay coil should be driven by a transistor or driver circuit so the microcontroller pin current remains within its specified limits, while flyback protection is placed across the inductive load. The compact six-pin package reduces board area, but the designer must plan pin multiplexing carefully and use the manufacturer pin-description table when assigning MCU, programming, and control functions.
推荐
Small Sensor Interface
The PIC10F202-E/MC is useful for a compact sensor interface that converts a small number of discrete inputs into a control or alarm output. Four I/O pins can accommodate digital sensors, threshold inputs, or status signals, while the 4 MHz core supports sampling routines and basic filtering. For analog measurement, the selected PIC10F202 variant's available analog-capable pins must be confirmed in the six-pin package pin table before the PCB is released. Firmware can implement hysteresis, debounce counters, and threshold logic while occupying less than the available 512 implemented 12-bit program words. Because the MCU has only 24 bytes of RAM, measurements and state variables should be compact, and application code must avoid relying on stack depth or peripheral features not present in the selected device variant.
推荐
Household Appliance Controller
PIC10F202-E/MC fits low-cost household appliance subassemblies that need local logic, persistent settings, and a minimal footprint. Typical tasks include button decoding, motor-step sequencing, timer management, and safety-state handling. The 33-instruction RISC core executes most instructions in one cycle at 4 MHz, allowing the controller to service multiple inputs without a large clock tree. Flash memory preserves operating parameters between power cycles, while the 24-byte RAM is sufficient for compact state variables. A practical design should keep the power conversion stage physically separate from sensitive MCU routing, provide local decoupling, and confirm the available pins before allocating functions. Firmware size must remain within 512 implemented program words, making efficient tables and branch structure important for feature-rich appliance products.
推荐
Fan and Small Motor Controller
The PIC10F202-E/MC can control a small fan or low-current motor subsystem through external transistor circuitry, making it suitable for compact thermal-management modules. Its GPIO resources can accept speed commands or sensor inputs, while the 4 MHz processing rate supports basic closed-loop timing and fault counting. The MCU should not drive an inductive load directly; a suitably rated driver and protection network are required. The small Flash footprint can store a lookup table for speed levels, timing profiles, and fault codes, while the fully static architecture supports efficient idle periods between commands. Because available RAM is limited to 24 bytes, control loops should use minimal state storage, and the firmware must include startup delays, lockout behavior, and a defined output-off state after reset to prevent unintended motion.
推荐
Programmable Logic Controller
PIC10F202-E/MC can serve as a compact programmable logic controller for simple discrete automation, providing sequenced outputs and configurable input behavior in a six-pin package. Its Flash-based firmware permits repeatable operation, and the four I/O pins are suited to small relay, indicator, and interlock arrangements. A useful implementation places the MCU beside screw terminals or a compact connector, with external buffers for loads and interface circuits for long wiring. The 512 implemented program words are sufficient for compact ladder-like state logic, timers, and diagnostics but not extensive communication middleware. Firmware should prioritize deterministic execution, include safe output states during reset, and test every configuration-word setting. The -/MC footprint and pin allocation should be validated against the package drawing before committing the PCB layout.
推荐
推荐产品汇总
工程参考数据: PIC10F202-E/MC ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | PIC10F200-E/MC | PIC10F204-E/MC | PIC10F206-E/MC | PIC10F202-I/MC |
|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 6-pin -/MC package | 6-pin -/MC package | 6-pin -/MC package | 6-pin -/MC package | 6-pin -/MC package |
| Architecture | 8-bit RISC | 8-bit RISC | 8-bit RISC | 8-bit RISC | 8-bit RISC |
| Maximum Clock Frequency | 4 MHz | 4 MHz | 4 MHz | 4 MHz | 4 MHz |
| Program Memory | 768 bytes (512 x 12 bits) | 384 bytes (256 x 12 bits) | 768 bytes (512 x 12 bits) | 768 bytes (512 x 12 bits) | 768 bytes (512 x 12 bits) |
| General-Purpose I/O | 4 pins | 4 pins | 4 pins | 4 pins | 4 pins |
| Instruction Set | 33 single-word instructions | 33 single-word instructions | 33 single-word instructions | 33 single-word instructions | 33 single-word instructions |
| Temperature Grade | Extended temperature grade indicated by -E | Extended temperature grade indicated by -E | Extended temperature grade indicated by -E | Extended temperature grade indicated by -E | Industrial temperature grade indicated by -I |
关键差异点
- Twice the implemented program memory of PIC10F200-E/MC (对比 PIC10F200-E/MC)
- Retains the same core speed and instruction set as PIC10F206-E/MC (对比 PIC10F206-E/MC)
- Four I/O pins in a compact six-pin package (对比 ATTINY13A-SUR)
- Fully static Flash operation for compact control designs (对比 PIC10F200-E/MC)
设计说明
Treat the six-pin package as an I/O-constrained design. Before schematic capture, create a pin-budget table covering power, ground, programming, communications, inputs, and outputs. Follow the -/MC land pattern in Microchip Data Sheet 40001239F.pdf rather than reusing a SOT-23-6 footprint solely because both packages have six leads. Place the supply bypass capacitor directly across VDD and VSS, and keep the programming pads or connector accessible without mechanical changes.
Apply the exact supply limits and decoupling recommendations from the manufacturer electrical characteristics. The 4 MHz operating speed does not remove the need to sequence power rails when the board also contains sensors or external logic. Check brownout behavior, input levels during startup, and the state of all outputs at reset. Use a dedicated local VDD path and ground-return connection to prevent switching currents in the external load circuitry from creating false transitions on the MCU pins.
Do not assume that every six-pin PIC10F option has the same physical pinout or that all family members implement identical memory and peripherals. The PIC10F202 has 512 physically implemented 12-bit program words, so firmware must fit that map, and a PIC10F200 variant provides only half that program-memory capacity. Validate the linker configuration, configuration words, device selected by the build system, and reset behavior after any family substitution.
Keep high-current or switching-node paths away from the MCU and its decoupling capacitor. If an I/O drives a relay, motor, or LED driver, route that signal through the appropriate transistor and protection network, and provide a quiet return path to the power stage. Although most instructions execute in 1 microsecond at 4 MHz, deterministic firmware should not rely on that figure without accounting for two-cycle branches, interrupt latency, and peripheral timing.
The 24-byte RAM limits temporary variables, stack depth, and buffered data. Estimate the compiler-generated stack requirement for the deepest interrupt and function-call path, then leave margin rather than treating all 24 bytes as available application storage. For state machines, use program Flash for lookup tables and constants, keep frequently used state in RAM, and test interrupt nesting against the selected configuration-word settings.
合规信息
No specific RoHS, REACH, lead-free, halogen-free, conflict-minerals, or automotive qualification statement appears in the product information for this exact ordering code. AEC-Q100 status is not applicable because this ordering code is not identified as an automotive-qualified variant.