TLV2761CD - 500 kHz RRIO Op Amp | Texas Instruments
MPN: TLV2761CD ✓ NakahandaTLV2761CD Ulas
An operational amplifier, or op amp, is a voltage-controlled differential amplifier used to amplify, buffer, compare, filter, or reshape analog signals. The TLV2761 belongs to the rail-to-rail input and output amplifier family, where the input common-mode range and output swing approach the supply rails. This makes the device useful where signals can occupy much of the available supply range and where conventional input stages would clip.
Key features include 500 kHz gain-bandwidth product, operation down to 1.8 V, and approximately 20 µA quiescent current. The rail-to-rail input stage supports direct sensing of low-amplitude signals, while the rail-to-rail output stage provides useful dynamic output range. These characteristics make the amplifier appropriate for battery-powered sensing, low-voltage instrumentation, buffered analog measurement, and embedded control systems.
The TLV2761CD uses a CMOS-based operational-amplifier architecture optimized for low-voltage operation. A single circuit is sufficient when an application requires one independent gain stage, comparator-style buffering, or a basic active filter. The 500 kHz bandwidth supports moderate-frequency signal paths without requiring the higher current and power consumption associated with faster general-purpose amplifiers.
Typical uses include sensor signal conditioning, low-voltage ADC drivers, portable measurement instruments, industrial process monitoring, battery-operated diagnostic equipment, and embedded control interfaces. The low quiescent current is particularly valuable in designs that spend substantial time between measurement events because the amplifier's own supply demand remains small during those intervals.
When designing around the TLV2761CD, verify the required output swing against the actual load and supply voltage. Decoupling capacitors should be placed close to the supply pins, and sensitive analog inputs should be routed away from switching nodes. Because rail-to-rail operation can involve input or output transition regions, input and output signals should be evaluated across the full operating range rather than only at the nominal supply voltage.
This page combines the manufacturer product information with package, ordering, drop-in comparison, application guidance, and design considerations. The resulting reference helps engineers evaluate the TLV2761CD for low-voltage analog systems while keeping footprint compatibility and circuit-level constraints in view.
Mga alternatibo na pwedeng ilagay na TLV2761CD — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.
Variante sa Seri na ito
Katulad na modelo sa serye na katugma sa pagpasok TLV2761CD (parehas na form factor at footprint) — pagkakaiba sa Amplifier Type, Operating Temperature Range, Package, Input Common-Mode Range, Supply Voltage Range.
TLV2761ID
✅ Drop-InMagkontak para sa presyo
Tingnan ang Datasheet →TLV2761CDR
✅ Drop-In📋 Alternatibo na Reference (hindi sa katalogo)
TLV2761IDR
✅ Drop-In📋 Alternatibo na Reference (hindi sa katalogo)
TLV2761IDRG4
✅ Drop-In📋 Alternatibo na Reference (hindi sa katalogo)
TLV2761CDG4
✅ Drop-In ⚠️ Mga Talaan Hindi Naiwerikmo📋 Alternatibo na Reference (hindi sa katalogo)
TLV2761CD Mga Pinakamataas na Rating at Electrical Characteristics
| Number of Amplifiers | 1 circuit |
| Amplifier Type | Single operational amplifier |
| Gain-Bandwidth Product | 500 kHz |
| Maximum Recommended Supply Voltage | 3.6 V |
| Minimum Operating Supply Voltage | 1.8 V |
| Kuru-kuryente ng Kapayapaan | 20 µA |
| Input Common-Mode Range | Rail-to-rail |
| Output Swing | Rail-to-rail |
| Hanay ng Temperature na Operasyon | 0 °C to 70 °C |
| Packhaging | 8-pin SOIC (D) |
| Package Width | 3.90 mm |
| Lead Pitch | 1.27 mm |
| Uri ng Pagpapasok | Surface mount |
Gabay sa Pin Configuration ng TLV2761CD 3.90 mm
Pin configuration para sa TLV2761CD (3.90 mm package). Ang analog component na ito ay may input, output, at power supply pins. Sumangguni sa datasheet ng manufacturer para sa offset null, compensation, at enable pin configurations. Perpekto para sa signal conditioning at amplifier circuits.
Wala ng detalyadong pinout data na magagamit para sa TLV2761CD.
Sumangguni sa datasheet para sa buong pin configuration.
Tipikal na mga Gamit
TLV2761CD ay nararapat para sa 6 aplikasyons: Battery-Powered Sensor Signal Conditioning, Low-Voltage ADC Input Driver, Portable Measurement Instrumentation, Industrial Process Monitoring, Embedded Control Signal Buffering, Battery-Operated Diagnostic Equipment.
Battery-Powered Sensor Signal Conditioning
The TLV2761CD suits low-voltage sensor conditioning because it operates from 1.8 V, consumes approximately 20 µA in the quiescent state, and accepts rail-to-rail input voltages. Place the amplifier directly between a sensor and an ADC input to amplify weak bipolar or unipolar signals without requiring a higher supply voltage. Its 500 kHz gain-bandwidth product supports moderate-bandwidth sensing, while the low quiescent current helps preserve battery life between measurements. Confirm the sensor output range, ADC input range, and required closed-loop gain before selecting resistor values.
Inirekomenda
Low-Voltage ADC Input Driver
The TLV2761CD can provide a rail-to-rail input and output interface between a low-voltage sensor network and an ADC. Its 1.8 V minimum operating voltage supports compact systems, and the 500 kHz gain-bandwidth product allows useful signal bandwidth at modest closed-loop gains. The approximately 20 µA quiescent current is favorable for portable acquisition systems. Confirm ADC settling requirements, input capacitance, allowable noise, and output-voltage headroom because a rail-to-rail output does not guarantee full rail-to-rail swing at every load.
Inirekomenda
Portable Measurement Instrumentation
The TLV2761CD is appropriate for portable measurement instruments where supply capacity is limited and signal integrity must be maintained near the supply rails. The rail-to-rail input stage reduces clipping when the measured signal approaches either supply limit, while the rail-to-rail output stage increases usable dynamic range. Low quiescent current of approximately 20 µA and operation down to 1.8 V help reduce system power. Validate the complete measurement chain under minimum supply voltage, maximum source impedance, temperature extremes, and the required input bandwidth.
Inirekomenda
Industrial Process Monitoring
The TLV2761CD can amplify low-level process signals in compact industrial monitoring equipment when the design operates within its 0 °C to 70 °C commercial range. Rail-to-rail input operation accommodates sensor outputs near the supply rails, and the 500 kHz gain-bandwidth product handles signals beyond static DC measurement. Low quiescent current helps when many sensing channels are active. For installations with wider temperature requirements, select the TLV2761ID and verify its complete electrical characteristics before release.
Inirekomenda
Embedded Control Signal Buffering
The TLV2761CD can buffer a control or feedback signal between a sensor, comparator, and embedded controller. Its approximately 20 µA quiescent current fits compact control systems, and rail-to-rail input and output behavior provides flexibility when logic-like signals occupy much of the available voltage range. The 500 kHz gain-bandwidth product supports moderate-frequency feedback paths. Confirm stability with the selected capacitor values, source impedance, and load, and keep sensitive input routing away from switching circuitry.
Inirekomenda
Battery-Operated Diagnostic Equipment
The TLV2761CD supports compact diagnostic devices that amplify low-level physiological or equipment-monitoring signals from a 1.8 V or higher supply. Its low approximately 20 µA quiescent current reduces standby demand, while rail-to-rail operation improves usable signal range in compact analog sections. The 500 kHz gain-bandwidth product is adequate for many low-frequency diagnostic waveforms and modest anti-aliasing requirements. Validate noise, offset, electrode or sensor loading, patient or operator isolation requirements, and applicable regulatory requirements before using it in medical equipment.
Inirekomenda
Buod ng mga Inirekomendang Produkto
Impormasyon ng Talumpati sa Engineering for TLV2761CD — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.
Paunawang Hanapin
Ikabit sa Mga Alternatibo
| Parametro | Ito ang Producto | TLV2761ID | TLV2761CDR | TLV2761IDR | TLV2761IDRG4 | TLV2761CDG4 |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC |
| Gain-Bandwidth Product | 500 kHz | 500 kHz | 500 kHz | 500 kHz | 500 kHz | 500 kHz |
| Minimum Operating Supply Voltage | 1.8 V | 1.8 V | 1.8 V | 1.8 V | 1.8 V | 1.8 V |
| Maximum Recommended Supply Voltage | 3.6 V | 3.6 V | 3.6 V | 3.6 V | 3.6 V | 3.6 V |
| Quiescent Current | Approximately 20 µA | Approximately 20 µA | Approximately 20 µA | Approximately 20 µA | Approximately 20 µA | Approximately 20 µA |
| Input Common-Mode Range | Rail-to-rail | Rail-to-rail | Rail-to-rail | Rail-to-rail | Rail-to-rail | Rail-to-rail |
| Output Swing | Rail-to-rail | Rail-to-rail | Rail-to-rail | Rail-to-rail | Rail-to-rail | Rail-to-rail |
| Operating Temperature Range | 0 °C to 70 °C | Industrial temperature range; exact limits require datasheet confirmation | 0 °C to 70 °C | Industrial temperature range; exact limits require datasheet confirmation | Industrial temperature range; exact limits require datasheet confirmation | 0 °C to 70 °C |
Pangunahing mga Pagkakaiba
- Combines low-voltage operation with moderate signal bandwidth (kumpara saTLV2761ID)
- Defined commercial-temperature ordering option (kumpara saTLV2761ID)
- Rail-to-rail signal range in an 8-pin SOIC footprint (kumpara saTLV2761CDR)
Talaan ng Disenyo
Place the TLV2761CD close to the circuit elements that determine its behavior. Connect the supply-decoupling capacitor directly to the power and ground pins with short, low-impedance traces, and route the op-amp input and output nets away from clocks, switching regulators, and high-current return paths. Keep the feedback components close to the amplifier when the circuit uses resistive feedback, because excessive feedback-node capacitance can alter stability and bandwidth.
Design for a maximum recommended supply of 3.6 V while allowing operation down to 1.8 V. Verify the supply range across temperature and load, and check the input common-mode and output voltage limits at the minimum rail. Rail-to-rail input and output descriptions do not imply that the output reaches either rail exactly; leave the voltage margin required by the downstream load and by the application circuit.
Do not interpret the 500 kHz gain-bandwidth product as 500 kHz of closed-loop bandwidth at every gain setting. Actual bandwidth depends on noise gain, feedback resistance, source impedance, and load capacitance. Check the manufacturer stability and electrical-characteristics tables for the intended configuration. Also avoid driving long capacitive loads directly from the output unless the load and compensation arrangement have been evaluated.
For low-level sensor signals, use short input traces, guard techniques where appropriate, and a stable reference near the amplifier. The approximately 20 µA quiescent current makes the device attractive for portable systems, but input bias-current effects can become significant with high source impedance. Calculate the resulting offset using the actual sensor resistance and compare it with the application accuracy requirement.
Impormasyon ng Pagsunod sa Kautusan
The manufacturer ordering information identifies a commercial-temperature 8-pin SOIC ordering option, but explicit RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations were not present in the referenced product information. AEC-Q100 qualification is not applicable to the identified standard TLV2761CD ordering option.