Texas Instruments

TLV2761CD - 500 kHz RRIO Op Amp | Texas Instruments

MPN: TLV2761CD ✓ فعال
3.6 V Vdss 20 µA Id 8-pin SOIC (D) Package
MOQ: 1 |

TLV2761CD جائزہ

The Texas Instruments TLV2761CD is a single-amplifier, rail-to-rail input and output operational amplifier with 500 kHz gain-bandwidth product, 3.6 V maximum recommended supply voltage, and low 20 µA quiescent-current operation. It is housed in an 8-pin SOIC package and is intended for compact, low-power analog signal-conditioning systems operating from a 3.6 V maximum supply.

An operational amplifier, or op amp, is a voltage-controlled differential amplifier used to amplify, buffer, compare, filter, or reshape analog signals. The TLV2761 belongs to the rail-to-rail input and output amplifier family, where the input common-mode range and output swing approach the supply rails. This makes the device useful where signals can occupy much of the available supply range and where conventional input stages would clip.

Key features include 500 kHz gain-bandwidth product, operation down to 1.8 V, and approximately 20 µA quiescent current. The rail-to-rail input stage supports direct sensing of low-amplitude signals, while the rail-to-rail output stage provides useful dynamic output range. These characteristics make the amplifier appropriate for battery-powered sensing, low-voltage instrumentation, buffered analog measurement, and embedded control systems.

The TLV2761CD uses a CMOS-based operational-amplifier architecture optimized for low-voltage operation. A single circuit is sufficient when an application requires one independent gain stage, comparator-style buffering, or a basic active filter. The 500 kHz bandwidth supports moderate-frequency signal paths without requiring the higher current and power consumption associated with faster general-purpose amplifiers.

Typical uses include sensor signal conditioning, low-voltage ADC drivers, portable measurement instruments, industrial process monitoring, battery-operated diagnostic equipment, and embedded control interfaces. The low quiescent current is particularly valuable in designs that spend substantial time between measurement events because the amplifier's own supply demand remains small during those intervals.

When designing around the TLV2761CD, verify the required output swing against the actual load and supply voltage. Decoupling capacitors should be placed close to the supply pins, and sensitive analog inputs should be routed away from switching nodes. Because rail-to-rail operation can involve input or output transition regions, input and output signals should be evaluated across the full operating range rather than only at the nominal supply voltage.

This page combines the manufacturer product information with package, ordering, drop-in comparison, application guidance, and design considerations. The resulting reference helps engineers evaluate the TLV2761CD for low-voltage analog systems while keeping footprint compatibility and circuit-level constraints in view.

کے لیے ڈراپ اِن متبادل TLV2761CD — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔

اس سیریز میں مختلف ورژن

اسی سیریز کے ماڈلز جو ڈراپ اِن مطابقت رکھتے ہیں TLV2761CD (یکساں فارم فیکٹر اور فٹ پرنٹ) — میں مختلف Amplifier Type, Operating Temperature Range, Package, Input Common-Mode Range, Supply Voltage Range.

Texas Instruments
Amplifier Type: General Purpose Operational Amplifier, Rail-to-Rail Input/Output
Package: 8-SOIC (0.154 in, 3.90 mm width)
Input Common-Mode Range: Rail-to-rail (includes both supply rails)
موازنہ کریں TLV2761CD →
Texas Instruments
Amplifier Type: Single voltage-feedback operational amplifier
Operating Temperature Range: -40°C to +85°C
Supply Voltage Range: 1.8 V to 3.6 V recommended maximum
موازنہ کریں TLV2761CD →

TLV2761ID

✅ ڈراپ-اِن
Texas Instruments
📦 8-SOIC
Single voltage-feedback operational amplifier · 1 circuit · 1.8 V to 3.6 V recommended maximum · 3.6 V · 1.8 V · 500 kHz · 20 µA · Rail-to-rail input

قیمت کے لیے رابطہ کریں

ڈیٹا شیٹ دیکھیں →

TLV2761CDR

✅ ڈراپ-اِن
📦 8-SOIC
Same electrical ratings and 8-SOIC footprint; tape-and-reel ordering code differs with 0 V, 0 kHz, and 0 µA change in the listed core ratings

📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)

TLV2761IDR

✅ ڈراپ-اِن
📦 8-SOIC
Same 8-SOIC footprint and core electrical ratings; industrial-temperature ordering and reel packing differ with 0 V, 0 kHz, and 0 µA change

📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)

TLV2761IDRG4

✅ ڈراپ-اِن
📦 8-SOIC
Same core voltage, bandwidth, rail-to-rail architecture, and approximately 20 µA class operation; green ordering designation and reel packing differ

📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)

TLV2761CDG4

✅ ڈراپ-اِن ⚠️ تفصیلات غیر تصدیق شدہ
📦 8-SOIC
Same-family 8-SOIC option with equivalent core voltage, bandwidth, rail-to-rail, and low-power ratings; green ordering designation differs

📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)

TLV2761CD زیادہ سے زیادہ ریٹنگز اور برقی خصوصیات

Number of Amplifiers 1 circuit
Amplifier Type Single operational amplifier
Gain-Bandwidth Product 500 kHz
Maximum Recommended Supply Voltage 3.6 V
Minimum Operating Supply Voltage 1.8 V
کوئیسینٹ کرنٹ 20 µA
Input Common-Mode Range Rail-to-rail
Output Swing Rail-to-rail
آپریٹنگ درجہ حرارت رینج 0 °C to 70 °C
پیکیج 8-pin SOIC (D)
Package Width 3.90 mm
Lead Pitch 1.27 mm
ماؤنٹنگ ٹائپ Surface mount

TLV2761CD 3.90 mm پن کنفیگریشن گائیڈ

TLV2761CD (3.90 mm پیکیج) کے لیے پن کنفیگریشن۔ اس اینالاگ کمپوننٹ میں اِن پٹ، آؤٹ پٹ اور پاور سپلائی پنز شامل ہیں۔ آفسیٹ نل، کمپنسیشن اور اِن ایبل پن کنفیگریشنز کے لیے مینوفیکچرر کے ڈیٹا شیٹ سے رجوع کریں۔ سگنل کنڈیشننگ اور ایمپلیفائر سرکٹس کے لیے مثالی۔

TLV2761CD کے لیے 3.90 mm پیکیج پن آؤٹ ڈایاگرام

کے لیے تفصیلی پن آؤٹ ڈیٹا دستیاب نہیں TLV2761CD.

رجوع کریں ڈیٹا شیٹ مکمل پن کنفیگریشن کے لیے۔

عام استعمالات

TLV2761CD کے لیے موزوں ہے 6 ایپلیکیشنs: Battery-Powered Sensor Signal Conditioning, Low-Voltage ADC Input Driver, Portable Measurement Instrumentation, Industrial Process Monitoring, Embedded Control Signal Buffering, Battery-Operated Diagnostic Equipment.

🧩

Battery-Powered Sensor Signal Conditioning

The TLV2761CD suits low-voltage sensor conditioning because it operates from 1.8 V, consumes approximately 20 µA in the quiescent state, and accepts rail-to-rail input voltages. Place the amplifier directly between a sensor and an ADC input to amplify weak bipolar or unipolar signals without requiring a higher supply voltage. Its 500 kHz gain-bandwidth product supports moderate-bandwidth sensing, while the low quiescent current helps preserve battery life between measurements. Confirm the sensor output range, ADC input range, and required closed-loop gain before selecting resistor values.

📊

Low-Voltage ADC Input Driver

The TLV2761CD can provide a rail-to-rail input and output interface between a low-voltage sensor network and an ADC. Its 1.8 V minimum operating voltage supports compact systems, and the 500 kHz gain-bandwidth product allows useful signal bandwidth at modest closed-loop gains. The approximately 20 µA quiescent current is favorable for portable acquisition systems. Confirm ADC settling requirements, input capacitance, allowable noise, and output-voltage headroom because a rail-to-rail output does not guarantee full rail-to-rail swing at every load.

🔧

Portable Measurement Instrumentation

The TLV2761CD is appropriate for portable measurement instruments where supply capacity is limited and signal integrity must be maintained near the supply rails. The rail-to-rail input stage reduces clipping when the measured signal approaches either supply limit, while the rail-to-rail output stage increases usable dynamic range. Low quiescent current of approximately 20 µA and operation down to 1.8 V help reduce system power. Validate the complete measurement chain under minimum supply voltage, maximum source impedance, temperature extremes, and the required input bandwidth.

🏭

Industrial Process Monitoring

The TLV2761CD can amplify low-level process signals in compact industrial monitoring equipment when the design operates within its 0 °C to 70 °C commercial range. Rail-to-rail input operation accommodates sensor outputs near the supply rails, and the 500 kHz gain-bandwidth product handles signals beyond static DC measurement. Low quiescent current helps when many sensing channels are active. For installations with wider temperature requirements, select the TLV2761ID and verify its complete electrical characteristics before release.

⚡

Embedded Control Signal Buffering

The TLV2761CD can buffer a control or feedback signal between a sensor, comparator, and embedded controller. Its approximately 20 µA quiescent current fits compact control systems, and rail-to-rail input and output behavior provides flexibility when logic-like signals occupy much of the available voltage range. The 500 kHz gain-bandwidth product supports moderate-frequency feedback paths. Confirm stability with the selected capacitor values, source impedance, and load, and keep sensitive input routing away from switching circuitry.

💊

Battery-Operated Diagnostic Equipment

The TLV2761CD supports compact diagnostic devices that amplify low-level physiological or equipment-monitoring signals from a 1.8 V or higher supply. Its low approximately 20 µA quiescent current reduces standby demand, while rail-to-rail operation improves usable signal range in compact analog sections. The 500 kHz gain-bandwidth product is adequate for many low-frequency diagnostic waveforms and modest anti-aliasing requirements. Validate noise, offset, electrode or sensor loading, patient or operator isolation requirements, and applicable regulatory requirements before using it in medical equipment.

تجویز کردہ پروڈکٹس کا خلاصہ

TLV2761ID Texas Instruments استعمال ہوتا ہے: Battery-Powered Sensor Signal Conditioning, Low-Voltage ADC Input Driver, Portable Measurement Instrumentation, Industrial Process Monitoring, Battery-Operated Diagnostic Equipment TLV2761CDR Same-family SOIC option with reel-packed ordering استعمال ہوتا ہے: Battery-Powered Sensor Signal Conditioning, Low-Voltage ADC Input Driver, Embedded Control Signal Buffering TLV2761CDG4 Same-family green-designation SOIC option استعمال ہوتا ہے: Portable Measurement Instrumentation, Battery-Operated Diagnostic Equipment TLV2761IDR Reel-packed industrial-temperature family option استعمال ہوتا ہے: Industrial Process Monitoring, Embedded Control Signal Buffering
What are the key specifications of TLV2761CD that engineers should know?
The TLV2761CD is a single, low-power operational amplifier with 500 kHz gain-bandwidth product, operation down to 1.8 V, a 3.6 V maximum recommended supply voltage, and approximately 20 µA quiescent current. According to the Texas Instruments TLV2761 product page, it provides rail-to-rail input and output operation in an 8-pin SOIC package. These specifications position it for low-voltage, low-power analog signal conditioning where a single amplifier must handle inputs and outputs near the supply rails.
What is the operating voltage of TLV2761CD?
The TLV2761CD operates down to 1.8 V and has a maximum recommended supply voltage of 3.6 V. The Texas Instruments TLV2761 family information describes operation from single-supply rails and also identifies suitability for split-supply arrangements around a 3.6 V total range. Keep the actual supply below the 3.6 V maximum while retaining adequate headroom for the intended common-mode input and output operating points.
Is TLV2761CD rail-to-rail input and output?
Yes, the TLV2761CD uses rail-to-rail input and output operation. According to the Texas Instruments TLV2761 product page, this allows the amplifier to accept input voltages near the supply rails and produce output swings closer to the rails than a conventional non-rail-to-rail amplifier. Rail-to-rail behavior is useful in low-voltage systems, although designers should still verify output swing under the intended load and supply conditions.
What is the bandwidth of TLV2761CD?
The TLV2761CD has a 500 kHz gain-bandwidth product. The Texas Instruments TLV2761 product information identifies the device as a single 500 kHz rail-to-rail operational amplifier. Actual closed-loop bandwidth depends on the selected noise gain and stability, so a 500 kHz gain-bandwidth figure should not be interpreted as 500 kHz usable bandwidth at every gain setting.
Where can I download the TLV2761CD datasheet PDF?
The TLV2761CD datasheet and ordering information are available from the Texas Instruments TLV2761 product page at https://www.ti.com/product/TLV2761. The manufacturer page links the device data sheet, part details, application information, and ordering options. Use the manufacturer document for the authoritative pin description, recommended operating conditions, electrical characteristics, and application guidance.
Where can I find the TLV2761CD pinout?
The TLV2761CD pinout should be obtained from the pin-description table in the Texas Instruments TLV2761 manufacturer datasheet. The exact ordering option is specified as an 8-pin SOIC package with 8 pins. Use the package drawing and pin table together when assigning PCB tracks, particularly for supply pins, input terminals, and the output terminal.
What is the best drop-in replacement for TLV2761CD?
The TLV2761ID is the closest same-family SOIC option identified for the TLV2761CD because it retains the single-amplifier architecture, rail-to-rail operation, 500 kHz gain-bandwidth product, 1.8 V minimum supply capability, and 20 µA-class power consumption. Before replacement, compare temperature grade, supply limits, offset, noise, stability, and exact pin functions in the manufacturer data sheets rather than relying on package appearance alone.
Can TLV2761ID replace TLV2761CD in an existing PCB?
The TLV2761ID can be considered as a same-family, 8-pin SOIC replacement after confirming electrical and temperature requirements. The two devices share the 1.8 V minimum operating voltage, 3.6 V maximum recommended supply voltage, 500 kHz gain-bandwidth product, rail-to-rail input and output architecture, and approximately 20 µA quiescent current. The TLV2761ID is identified as an industrial-temperature option, so verify the required temperature range and exact offset specifications before substitution.
When should I choose TLV2761CD over TLV2761ID?
Choose TLV2761CD when the required commercial-temperature operating range of 0 °C to 70 °C is sufficient and the exact TLV2761CD ordering option has been qualified. Choose TLV2761ID when a broader industrial-temperature range is required and its electrical characteristics satisfy the circuit. Both use an 8-pin SOIC format and share the principal low-voltage, rail-to-rail, 500 kHz amplifier characteristics, making the temperature requirement the primary decision point.
TLV2761CD vs TLV2761ID: which is better for battery-powered instrumentation?
TLV2761CD is suitable for battery-powered instrumentation operating within 0 °C to 70 °C, while TLV2761ID is the more appropriate choice when industrial-temperature coverage is required. Both provide a 500 kHz gain-bandwidth product, operation down to 1.8 V, rail-to-rail input and output behavior, and approximately 20 µA quiescent current. The selection should therefore be driven primarily by temperature grade rather than basic power or bandwidth requirements.
Is TLV2761CD suitable for low-voltage sensor signal conditioning?
The TLV2761CD is suitable for low-voltage sensor signal conditioning when the sensor output remains within the amplifier's common-mode operating range and the required bandwidth is below the closed-loop limit set by the chosen gain. Its 1.8 V minimum supply, rail-to-rail input, 500 kHz gain-bandwidth product, and 20 µA quiescent current suit compact battery-powered measurement systems.
How should I design the power decoupling for TLV2761CD?
Place the supply-decoupling capacitor immediately adjacent to the TLV2761CD power and ground pins, and keep the connection traces short to minimize supply impedance and high-frequency pickup. The manufacturer data sheet should be consulted for the recommended capacitor value and stability requirements. Because the device supports operation down to 1.8 V, verify capacitor DC-bias derating and ensure the local supply remains within the 3.6 V maximum recommended rating.
Does TLV2761CD require a bypass capacitor for stable operation?
The TLV2761CD should be used with the decoupling and application network specified in the Texas Instruments manufacturer datasheet. Bypassing the supply pins close to the device reduces high-frequency supply impedance and helps maintain stable operation, particularly with the long connection traces found in point-to-point wiring or compact mixed-signal boards. Confirm the required capacitance and ESR considerations for the selected gain and load.
How much current does TLV2761CD consume?
The TLV2761CD draws approximately 20 µA quiescent current. According to the Texas Instruments TLV2761 family description, the amplifier provides 500 kHz bandwidth from approximately 20 µA while operating down to 1.8 V. Actual supply current can increase with output current, slew rate, capacitive loading, and operating frequency, so quiescent current is most useful for estimating standby consumption.
Where to buy TLV2761CD online and what is its lead time?
Use the Request a Quote form on this page to request current TLV2761CD availability, order quantity, price, and lead time. The 8-pin SOIC TLV2761CD is listed as an active Texas Instruments ordering option with an operating range of 0 °C to 70 °C. Submit the required quantity and target delivery date so the current supply position can be confirmed before committing the design.
What is the price and stock status of TLV2761CD?
Use the Request a Quote form on this page for the current TLV2761CD price, stock position, minimum order quantity, and shipment estimate. Commercial availability can change by package quantity and date, so avoid using an old listing as a production commitment. Include the required delivery schedule and order quantity with the request to obtain an actionable quotation.
Can a TLV2761CD replace a TLV9041 in the same circuit?
The TLV2761CD should not be treated as an automatic TLV9041 replacement because their electrical characteristics and function implementations differ. The TLV2761CD is specified as a 3.6 V, 500 kHz, rail-to-rail operational amplifier, while the TLV9041 is identified separately as a micropower rail-to-rail amplifier. Verify package, supply range, bandwidth, quiescent current, offset, output swing, and every pin function in the manufacturer data sheets before substitution.

کے لیے انجینئرنگ ریفرنس ڈیٹا TLV2761CD — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔

انتخاب کی گائیڈ

Choose TLV2761CD for compact, low-voltage analog designs operating from 1.8 V to 3.6 V when the 0 °C to 70 °C range is adequate and a single 500 kHz rail-to-rail amplifier is sufficient. Its approximately 20 µA quiescent current favors battery-powered sensing, portable instrumentation, and embedded monitoring. Choose TLV2761ID when the same core electrical architecture and SOIC footprint are needed over a wider industrial temperature range. TLV2761CDR, TLV2761IDR, and TLV2761IDRG4 are useful for specific production packing or green-designation requirements, but ordering code changes do not by themselves establish electrical equivalence. Before using any same-family alternative, compare input offset, noise, bias current, slew rate, output swing, load stability, and exact pin descriptions in the manufacturer data sheets.

متبادلات کے ساتھ موازنہ

پیرامیٹر یہ پروڈکٹ TLV2761ID TLV2761CDR TLV2761IDR TLV2761IDRG4 TLV2761CDG4
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Package 8-SOIC 8-SOIC 8-SOIC 8-SOIC 8-SOIC 8-SOIC
Gain-Bandwidth Product 500 kHz 500 kHz 500 kHz 500 kHz 500 kHz 500 kHz
Minimum Operating Supply Voltage 1.8 V 1.8 V 1.8 V 1.8 V 1.8 V 1.8 V
Maximum Recommended Supply Voltage 3.6 V 3.6 V 3.6 V 3.6 V 3.6 V 3.6 V
Quiescent Current Approximately 20 µA Approximately 20 µA Approximately 20 µA Approximately 20 µA Approximately 20 µA Approximately 20 µA
Input Common-Mode Range Rail-to-rail Rail-to-rail Rail-to-rail Rail-to-rail Rail-to-rail Rail-to-rail
Output Swing Rail-to-rail Rail-to-rail Rail-to-rail Rail-to-rail Rail-to-rail Rail-to-rail
Operating Temperature Range 0 °C to 70 °C Industrial temperature range; exact limits require datasheet confirmation 0 °C to 70 °C Industrial temperature range; exact limits require datasheet confirmation Industrial temperature range; exact limits require datasheet confirmation 0 °C to 70 °C

اہم امتیازی خصوصیات

  • Combines low-voltage operation with moderate signal bandwidth (بمقابلہTLV2761ID)
  • Defined commercial-temperature ordering option (بمقابلہTLV2761ID)
  • Rail-to-rail signal range in an 8-pin SOIC footprint (بمقابلہTLV2761CDR)

ڈیزائن نوٹس

Place the TLV2761CD close to the circuit elements that determine its behavior. Connect the supply-decoupling capacitor directly to the power and ground pins with short, low-impedance traces, and route the op-amp input and output nets away from clocks, switching regulators, and high-current return paths. Keep the feedback components close to the amplifier when the circuit uses resistive feedback, because excessive feedback-node capacitance can alter stability and bandwidth.

Design for a maximum recommended supply of 3.6 V while allowing operation down to 1.8 V. Verify the supply range across temperature and load, and check the input common-mode and output voltage limits at the minimum rail. Rail-to-rail input and output descriptions do not imply that the output reaches either rail exactly; leave the voltage margin required by the downstream load and by the application circuit.

Do not interpret the 500 kHz gain-bandwidth product as 500 kHz of closed-loop bandwidth at every gain setting. Actual bandwidth depends on noise gain, feedback resistance, source impedance, and load capacitance. Check the manufacturer stability and electrical-characteristics tables for the intended configuration. Also avoid driving long capacitive loads directly from the output unless the load and compensation arrangement have been evaluated.

For low-level sensor signals, use short input traces, guard techniques where appropriate, and a stable reference near the amplifier. The approximately 20 µA quiescent current makes the device attractive for portable systems, but input bias-current effects can become significant with high source impedance. Calculate the resulting offset using the actual sensor resistance and compare it with the application accuracy requirement.

تعمیل کی معلومات

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
لیڈ فری
Unknown
ہیلوجن فری
Unknown
کنفلیکٹ منرلز
Unknown

The manufacturer ordering information identifies a commercial-temperature 8-pin SOIC ordering option, but explicit RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations were not present in the referenced product information. AEC-Q100 qualification is not applicable to the identified standard TLV2761CD ordering option.

ڈیٹا کی تصدیق کی تاریخ: 2026-11-19 — ڈیٹا XAIPART کی کمپوننٹ انجینئرنگ ٹیم کے ذریعے تصدیق شدہ اور ترتیب شدہ

متعلقہ تلاشیں

TLV2761CD datasheet TLV2761CD pinout TLV2761CD datasheet pdf TLV2761CD specifications TLV2761CD equivalent TLV2761CD replacement TLV2761CD cross reference TLV2761CD vs TLV2761ID TLV2761CD footprint TLV2761CD application circuit Texas Instruments TLV2761CD TLV2761CD price TLV2761CD stock TLV2761 3.6V 500kHz RRIO op amp 8-SOIC TLV2761 pinout

متعلقہ اجزاء اور اصطلاحات

Texas Instruments TLV2761CD TLV2761 TLV2761ID TLV2761CDR TLV2761IDR TLV2761IDRG4 TLV2761CDG4 Operational amplifier Op amp Rail-to-rail input Rail-to-rail output CMOS operational amplifier Voltage regulator Analog signal conditioner Gain-bandwidth product Quiescent current Input common-mode range Output swing 8-SOIC SOIC family Surface mount SMD Low-voltage instrumentation Battery-powered sensing
فوری کوٹ RFQ
مکمل تفصیلات بھریں — ہماری سیلز ٹیم 24 گھنٹوں میں جواب دے گی
پارٹ نمبر مینوفیکچرر پیکج QTY ہدف قیمت کل رقم
✓
کوٹ جمع ہو گیا!

ہم 24 گھنٹوں کے اندر آپ کے ای میل کا جواب دیں گے

1
RFQ جمع ہو گیا
2
کوٹ موصول ہو گیا
3
آرڈر دے دیا گیا
4
ادائیگی
5
بھیج دیا گیا
6
ڈیلیور شدہ
RFQ تفصیلات دیکھیں