TLV2761CD - 500 kHz RRIO Op Amp | Texas Instruments
料号: TLV2761CD ✓ 量产中TLV2761CD 概述
An operational amplifier, or op amp, is a voltage-controlled differential amplifier used to amplify, buffer, compare, filter, or reshape analog signals. The TLV2761 belongs to the rail-to-rail input and output amplifier family, where the input common-mode range and output swing approach the supply rails. This makes the device useful where signals can occupy much of the available supply range and where conventional input stages would clip.
Key features include 500 kHz gain-bandwidth product, operation down to 1.8 V, and approximately 20 µA quiescent current. The rail-to-rail input stage supports direct sensing of low-amplitude signals, while the rail-to-rail output stage provides useful dynamic output range. These characteristics make the amplifier appropriate for battery-powered sensing, low-voltage instrumentation, buffered analog measurement, and embedded control systems.
The TLV2761CD uses a CMOS-based operational-amplifier architecture optimized for low-voltage operation. A single circuit is sufficient when an application requires one independent gain stage, comparator-style buffering, or a basic active filter. The 500 kHz bandwidth supports moderate-frequency signal paths without requiring the higher current and power consumption associated with faster general-purpose amplifiers.
Typical uses include sensor signal conditioning, low-voltage ADC drivers, portable measurement instruments, industrial process monitoring, battery-operated diagnostic equipment, and embedded control interfaces. The low quiescent current is particularly valuable in designs that spend substantial time between measurement events because the amplifier's own supply demand remains small during those intervals.
When designing around the TLV2761CD, verify the required output swing against the actual load and supply voltage. Decoupling capacitors should be placed close to the supply pins, and sensitive analog inputs should be routed away from switching nodes. Because rail-to-rail operation can involve input or output transition regions, input and output signals should be evaluated across the full operating range rather than only at the nominal supply voltage.
This page combines the manufacturer product information with package, ordering, drop-in comparison, application guidance, and design considerations. The resulting reference helps engineers evaluate the TLV2761CD for low-voltage analog systems while keeping footprint compatibility and circuit-level constraints in view.
直接替换替代料: TLV2761CD ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: TLV2761CD (相同外形与封装尺寸) ——差异在于 Amplifier Type, Operating Temperature Range, Package, Input Common-Mode Range, Supply Voltage Range.
TLV2761ID
✅ 直接替换联系询价
查看数据手册 →TLV2761CDR
✅ 直接替换📋 参考替代料(不在目录中)
TLV2761IDR
✅ 直接替换📋 参考替代料(不在目录中)
TLV2761IDRG4
✅ 直接替换📋 参考替代料(不在目录中)
TLV2761CDG4
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
TLV2761CD 最大额定值与电气特性
| Number of Amplifiers | 1 circuit |
| Amplifier Type | Single operational amplifier |
| Gain-Bandwidth Product | 500 kHz |
| Maximum Recommended Supply Voltage | 3.6 V |
| Minimum Operating Supply Voltage | 1.8 V |
| 静态电流 | 20 µA |
| Input Common-Mode Range | Rail-to-rail |
| Output Swing | Rail-to-rail |
| 工作温度范围 | 0 °C to 70 °C |
| 封装 | 8-pin SOIC (D) |
| Package Width | 3.90 mm |
| Lead Pitch | 1.27 mm |
| 安装类型 | Surface mount |
TLV2761CD 3.90 mm 引脚配置指南
TLV2761CD(3.90 mm 封装)的引脚配置。 该模拟元件具有输入、输出和电源引脚。请参阅制造商数据手册以了解失调调零、补偿和使能引脚配置。适用于信号调理和放大器电路。
暂无详细引脚数据: TLV2761CD.
请参阅 数据手册 以查看完整引脚配置。
典型应用
TLV2761CD 适用于 6 应用s: Battery-Powered Sensor Signal Conditioning, Low-Voltage ADC Input Driver, Portable Measurement Instrumentation, Industrial Process Monitoring, Embedded Control Signal Buffering, Battery-Operated Diagnostic Equipment.
Battery-Powered Sensor Signal Conditioning
The TLV2761CD suits low-voltage sensor conditioning because it operates from 1.8 V, consumes approximately 20 µA in the quiescent state, and accepts rail-to-rail input voltages. Place the amplifier directly between a sensor and an ADC input to amplify weak bipolar or unipolar signals without requiring a higher supply voltage. Its 500 kHz gain-bandwidth product supports moderate-bandwidth sensing, while the low quiescent current helps preserve battery life between measurements. Confirm the sensor output range, ADC input range, and required closed-loop gain before selecting resistor values.
推荐
Low-Voltage ADC Input Driver
The TLV2761CD can provide a rail-to-rail input and output interface between a low-voltage sensor network and an ADC. Its 1.8 V minimum operating voltage supports compact systems, and the 500 kHz gain-bandwidth product allows useful signal bandwidth at modest closed-loop gains. The approximately 20 µA quiescent current is favorable for portable acquisition systems. Confirm ADC settling requirements, input capacitance, allowable noise, and output-voltage headroom because a rail-to-rail output does not guarantee full rail-to-rail swing at every load.
推荐
Portable Measurement Instrumentation
The TLV2761CD is appropriate for portable measurement instruments where supply capacity is limited and signal integrity must be maintained near the supply rails. The rail-to-rail input stage reduces clipping when the measured signal approaches either supply limit, while the rail-to-rail output stage increases usable dynamic range. Low quiescent current of approximately 20 µA and operation down to 1.8 V help reduce system power. Validate the complete measurement chain under minimum supply voltage, maximum source impedance, temperature extremes, and the required input bandwidth.
推荐
Industrial Process Monitoring
The TLV2761CD can amplify low-level process signals in compact industrial monitoring equipment when the design operates within its 0 °C to 70 °C commercial range. Rail-to-rail input operation accommodates sensor outputs near the supply rails, and the 500 kHz gain-bandwidth product handles signals beyond static DC measurement. Low quiescent current helps when many sensing channels are active. For installations with wider temperature requirements, select the TLV2761ID and verify its complete electrical characteristics before release.
推荐
Embedded Control Signal Buffering
The TLV2761CD can buffer a control or feedback signal between a sensor, comparator, and embedded controller. Its approximately 20 µA quiescent current fits compact control systems, and rail-to-rail input and output behavior provides flexibility when logic-like signals occupy much of the available voltage range. The 500 kHz gain-bandwidth product supports moderate-frequency feedback paths. Confirm stability with the selected capacitor values, source impedance, and load, and keep sensitive input routing away from switching circuitry.
推荐
Battery-Operated Diagnostic Equipment
The TLV2761CD supports compact diagnostic devices that amplify low-level physiological or equipment-monitoring signals from a 1.8 V or higher supply. Its low approximately 20 µA quiescent current reduces standby demand, while rail-to-rail operation improves usable signal range in compact analog sections. The 500 kHz gain-bandwidth product is adequate for many low-frequency diagnostic waveforms and modest anti-aliasing requirements. Validate noise, offset, electrode or sensor loading, patient or operator isolation requirements, and applicable regulatory requirements before using it in medical equipment.
推荐
推荐产品汇总
工程参考数据: TLV2761CD ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | TLV2761ID | TLV2761CDR | TLV2761IDR | TLV2761IDRG4 | TLV2761CDG4 |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC |
| Gain-Bandwidth Product | 500 kHz | 500 kHz | 500 kHz | 500 kHz | 500 kHz | 500 kHz |
| Minimum Operating Supply Voltage | 1.8 V | 1.8 V | 1.8 V | 1.8 V | 1.8 V | 1.8 V |
| Maximum Recommended Supply Voltage | 3.6 V | 3.6 V | 3.6 V | 3.6 V | 3.6 V | 3.6 V |
| Quiescent Current | Approximately 20 µA | Approximately 20 µA | Approximately 20 µA | Approximately 20 µA | Approximately 20 µA | Approximately 20 µA |
| Input Common-Mode Range | Rail-to-rail | Rail-to-rail | Rail-to-rail | Rail-to-rail | Rail-to-rail | Rail-to-rail |
| Output Swing | Rail-to-rail | Rail-to-rail | Rail-to-rail | Rail-to-rail | Rail-to-rail | Rail-to-rail |
| Operating Temperature Range | 0 °C to 70 °C | Industrial temperature range; exact limits require datasheet confirmation | 0 °C to 70 °C | Industrial temperature range; exact limits require datasheet confirmation | Industrial temperature range; exact limits require datasheet confirmation | 0 °C to 70 °C |
关键差异点
- Combines low-voltage operation with moderate signal bandwidth (对比 TLV2761ID)
- Defined commercial-temperature ordering option (对比 TLV2761ID)
- Rail-to-rail signal range in an 8-pin SOIC footprint (对比 TLV2761CDR)
设计说明
Place the TLV2761CD close to the circuit elements that determine its behavior. Connect the supply-decoupling capacitor directly to the power and ground pins with short, low-impedance traces, and route the op-amp input and output nets away from clocks, switching regulators, and high-current return paths. Keep the feedback components close to the amplifier when the circuit uses resistive feedback, because excessive feedback-node capacitance can alter stability and bandwidth.
Design for a maximum recommended supply of 3.6 V while allowing operation down to 1.8 V. Verify the supply range across temperature and load, and check the input common-mode and output voltage limits at the minimum rail. Rail-to-rail input and output descriptions do not imply that the output reaches either rail exactly; leave the voltage margin required by the downstream load and by the application circuit.
Do not interpret the 500 kHz gain-bandwidth product as 500 kHz of closed-loop bandwidth at every gain setting. Actual bandwidth depends on noise gain, feedback resistance, source impedance, and load capacitance. Check the manufacturer stability and electrical-characteristics tables for the intended configuration. Also avoid driving long capacitive loads directly from the output unless the load and compensation arrangement have been evaluated.
For low-level sensor signals, use short input traces, guard techniques where appropriate, and a stable reference near the amplifier. The approximately 20 µA quiescent current makes the device attractive for portable systems, but input bias-current effects can become significant with high source impedance. Calculate the resulting offset using the actual sensor resistance and compare it with the application accuracy requirement.
合规信息
The manufacturer ordering information identifies a commercial-temperature 8-pin SOIC ordering option, but explicit RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations were not present in the referenced product information. AEC-Q100 qualification is not applicable to the identified standard TLV2761CD ordering option.