LM2902KPWR - Quad 26V 1.2MHz Op Amp | Texas Instruments (Tape & Reel)
MPN: LM2902KPWR ✓ AktifLM2902KPWR Genel Bakış
An operational amplifier is an analog integrated circuit that uses high open-loop gain to amplify differences between input signals. The LM2902 belongs to the general-purpose amplifier family, combining voltage amplification, buffering, filtering, and signal-conditioning functions in one package. Its four amplifiers make it useful where several independent analog channels are required without using four separate packages.
The LM2902KPWR provides a wide supply-voltage operating range, a 1.2 MHz gain-bandwidth product, and four amplifier circuits in one 14-pin TSSOP. The improved ESD rating of 2 kV is relevant in industrial and consumer equipment where handling transients or exposed connector inputs can affect an analog interface. The device is identified as a standard, general-purpose amplifier rather than a precision or low-noise amplifier.
Its internally compensated architecture simplifies closed-loop design because no external compensation network is required for typical voltage-feedback configurations. The 1.2 MHz bandwidth supports general-purpose signal amplification and moderate-frequency active filtering, while the wide supply range permits operation from conventional single supplies or higher industrial rails. Designers should still verify input and output common-mode limits, output swing, and stability against the final circuit topology.
Typical uses include sensor signal conditioning, industrial control loops, audio preamplification, low-frequency active filters, instrumentation interfaces, and general analog signal chains. Using four amplifiers in one package can also reduce PCB area and simplify design reviews compared with separate single-amplifier packages, although shared package limitations should be considered for applications requiring independent thermal or fault isolation.
For a new design, keep the TSSOP footprint and pin assignments of the LM2902KPWR unchanged, provide adequate input and output bypassing, and verify the selected bias point against the operating voltage and signal range. The manufacturer product page and datasheet are the appropriate references for ordering information, electrical limits, pin functions, and qualification details.
Drop-in alternatifler için LM2902KPWR — aynı paket, pin-başına uyumlu. PCB yeniden montajı gerektiren farklı paket bileşenleri dışlanmıştır.
Bu Serideki Variantlar
Yedek parça uyumlu olan aynı serideki modeller LM2902KPWR (aynı form faktörü ve ayağa oturma) — farklı olan Package, Amplifier Type, Operating Temperature Range, Gain-Bandwidth Product, Maximum Supply Voltage.
LM2902KD
✅ Yerleştirme ⚠️ Onaylanmamış ÖzelliklerFiyat için iletişime geçin
Veri Şablonunu Görüntüle →LM2902KVQPWR
✅ Yerleştirme ⚠️ Onaylanmamış ÖzelliklerFiyat için iletişime geçin
Veri Şablonunu Görüntüle →LM2902KPWR Maksimum Değerlendirmeler & Elektriksel Özellikler
| Number of Amplifiers | 4 amplifiers |
| Amplifier Type | General-purpose operational amplifier |
| Maximum Supply Voltage | 26 V |
| Gain-Bandwidth Product | 1.2 MHz |
| Improved ESD Protection | 2 kV |
| İşletim Sıcaklığı Aralığı | -40 °C to +125 °C |
| Supply Type | Single-supply operation |
| Compensation | Internally frequency compensated |
| Paket | 14-pin TSSOP |
| Package Width | 4.40 mm |
| Package Lead Width | 0.173 inch |
| Montaj Türü | Surface mount |
| Circuit Count | 4 circuits |
| Kategori | Instrumentation, operational amplifiers, buffer amplifiers |
LM2902KPWR 0.173 inch Pin Yapısı Kılavuzu
LM2902KPWR (0.173 inch paket) için pin yapısı. Bu analog bileşen, giriş, çıkış ve güç besleme pinleri içerir. Ofset null, telafi ve etkinleştirme pin yapılandırmaları için üretici veri kitapçığını referans alın. Sinyal işleme ve güç amplifikasyon devreleri için mükemmel bir bileşendir.
Ayrıntılı pin çıkış verisi mevcut değil: LM2902KPWR.
Aşağıdaki veri sayfası tam pin konfigürasyonu için.
Tipik Uygulamalar
LM2902KPWR için uygundur 6 uygulamas: Industrial Sensor Signal Conditioning, Audio Preamplification, Active Low-Frequency Filtering, Instrumentation Buffering, Control Loop Amplification, General-Purpose Interface Circuit.
Industrial Sensor Signal Conditioning
The LM2902KPWR is suitable for conditioning low-frequency sensor signals because it provides four general-purpose amplifier channels, a 1.2 MHz gain-bandwidth product, and single-supply operation with a 26 V maximum supply voltage. A typical channel can amplify a transducer output and buffer it into an analog-to-digital converter input. Internal frequency compensation keeps the voltage-feedback configuration simple, although the designer must verify the sensor’s common-mode range against the amplifier input limits and keep the layout away from switching nodes. Its 14-pin TSSOP package also reduces board area when several sensor channels require independent amplification.
Önerilen
Audio Preamplification
The LM2902KPWR can provide four independent general-purpose amplifier stages for low-frequency audio preamplification, active volume-control paths, or line-level buffering. The 1.2 MHz gain-bandwidth product is adequate for many general-purpose audio stages, while internal frequency compensation supports conventional non-inverting and inverting voltage-feedback configurations. Because it is not specified as a low-noise audio amplifier, the actual noise and distortion should be checked against the signal budget. The TSSOP-14 package helps reduce footprint compared with four separate single amplifiers, but grounding and output-drive considerations remain important.
Önerilen
Active Low-Frequency Filtering
The LM2902KPWR’s four independently usable amplifiers make it practical to implement active filters in instrumentation and control circuits. A practical application could combine buffered inputs, low-pass stages, and an output driver without requiring separate amplifier packages. The 1.2 MHz gain-bandwidth product provides useful bandwidth for low- and moderate-frequency filtering, and internal frequency compensation simplifies many voltage-feedback designs. Filter component tolerances and amplifier gain accuracy should be considered together. Use short feedback paths, stable reference grounding, and supply bypassing close to the device to reduce oscillation risk and improve repeatability.
Önerilen
Instrumentation Buffering
The LM2902KPWR can buffer instrumentation signals that must be referenced to a single supply. Four amplifier channels allow a design to combine input buffering, gain stages, and output isolation within one 14-pin TSSOP. The 26 V maximum supply rating supports circuits operating from a higher single rail, while the 1.2 MHz bandwidth covers many low-frequency measurement paths. The device should not automatically be treated as a dedicated precision instrumentation amplifier: input offset voltage, bias current, common-mode range, and output swing must meet the measurement error budget. Consider guarding sensitive input traces and avoiding capacitive loading on outputs.
Önerilen
Control Loop Amplification
The LM2902KPWR is applicable to low-frequency industrial control loops where error signals require amplification before driving an ADC, comparator, or downstream actuator interface. Its four amplifier channels can support feedback conditioning, summing, and signal isolation without using four separate packages. The 1.2 MHz gain-bandwidth product is generally more than adequate for slow control loops, and the wide single-supply range simplifies some industrial power architectures. Loop stability, output saturation, and input common-mode behavior must be checked across supply and load conditions. A solid reference ground and short feedback routes are essential.
Önerilen
General-Purpose Interface Circuit
The LM2902KPWR can serve as a compact interface-building block for logic-level, test-point, and analog-control circuits. Its four general-purpose amplifiers can provide comparators with external hysteresis, level conditioning, cross-coupling, or buffered test outputs. A 1.2 MHz gain-bandwidth product supports signal shaping beyond static comparators, while the 14-pin TSSOP package helps limit board area. Operation from one supply simplifies the power tree, but every amplifier must remain within its input and output common-mode limits. Use local supply bypassing and reserve adequate copper around the package for repeatable high-frequency behavior.
Önerilen
Mühendislik referans verileri: LM2902KPWR — karşılaştırma, tasarım rehberi ve uyumluluk bilgileri.
Seçim Kılavuzu
Alternatiflerle Karşılaştırma
| Parametre | Bu Ürün | LM2902K | LM2902KV |
|---|---|---|---|
| Package | 14-pin TSSOP | 14-pin TSSOP ordering option; confirm suffix | 14-pin TSSOP ordering option; confirm suffix |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Amplifier Count | 4 | 4 | 4 |
| Product Type | General-purpose operational amplifier | General-purpose operational amplifier | General-purpose operational amplifier |
| Gain-Bandwidth Product | 1.2 MHz | 1.2 MHz | 1.2 MHz |
| Improved ESD Protection | 2 kV | 2 kV | 2 kV |
| Operating Temperature | -40 °C to +125 °C | -40 °C to +125 °C | -40 °C to +125 °C |
| Compensation | Internally frequency compensated | Internally frequency compensated | Internally frequency compensated |
| Mounting Type | Surface mount | Surface mount | Surface mount |
Ana Farklılayıcılar
- Four independent amplifier channels in a compact TSSOP package (karşılaştırma:LM324ADR)
- General-purpose single-supply operation with a 26 V maximum rating (karşılaştırma:LM2902K)
- Improved ESD protection for general-purpose analog interfaces (karşılaştırma:LM2902KV)
Tasarım Notları
Place the supply bypass capacitor as close as practical to the device power pins and connect it to a low-impedance ground plane. The LM2902KPWR can operate from a single supply up to the listed 26 V maximum, but the selected rail must also satisfy the input common-mode and output swing limits. Keep high-current return paths away from the sensitive input and feedback nodes.
Preserve the 14-pin TSSOP footprint and follow the manufacturer land pattern when making a drop-in replacement. Route each output directly to its destination, keep feedback traces short, and avoid connecting input and output traces in parallel. A ground-plane connection near the package helps reduce parasitic inductance, while careful via placement can improve stability around the TSSOP leads.
Do not assume that any LM2902 suffix is electrically or mechanically interchangeable with LM2902KPWR. Check the package drawing, pin configuration, supply-voltage rating, temperature grade, input common-mode range, and output swing. A functional-family equivalent with a different package is not a drop-in replacement and requires PCB changes.
For sensor and instrumentation circuits, evaluate source impedance and input-bias-current effects as well as offset voltage. Keep sensitive input traces short, use a quiet ground reference, and avoid routing them near high-impedance nodes or switching converters. If capacitive loading is present at an output, verify stability using the manufacturer’s guidance rather than adding arbitrary capacitance.
Uyumluluk Bilgisi
The manufacturer product information identifies LM2902K as a general-purpose operational amplifier family, but it does not provide exact compliance conclusions for LM2902KPWR. Check the exact ordering suffix in Texas Instruments material and quality documentation.