LM2904WHDT - Dual Low-Power Op Amp, 8-SOIC | STMicroelectronics
MPN: LM2904WHDT ✓ AktifLM2904WHDT Genel Bakış
An operational amplifier is a voltage-feedback amplifier that uses high open-loop gain to amplify the difference between its inverting and non-inverting inputs. The LM2904 belongs to the operational-amplifier hierarchy, which sits within analog and mixed-signal semiconductors. Its dual-channel configuration reduces component count and board area when two amplifier functions are required on the same PCB.
Key features include 2 amplifier channels in one package, internal frequency compensation, and low-power operation from a single supply. The internal compensation removes the need for an external dominant-pole capacitor in conventional closed-loop applications. Single-ended outputs also simplify connection to analog-to-digital converters, sensors, transducers, and controller inputs that require a grounded-reference signal.
The architecture is suited to low-frequency precision-control applications because each channel has independent signal inputs. Designers can configure each amplifier as a voltage follower, non-inverting amplifier, or inverting amplifier. Unity-gain stability is especially useful for direct sensing and impedance-buffering positions where adding feedback components would be undesirable.
Typical uses include automotive sensor interfaces, industrial transducers, motor-control feedback networks, audio preamplifier stages, and low-frequency active filters. The STMicroelectronics product description identifies automotive and industrial control systems as primary application areas, while the low-power architecture benefits portable or distributed equipment operating from a single supply.
When assigning PCB tracks, use the manufacturer pin-description table and preserve the standard SOIC-8 pin sequence. Place each bypass capacitor close to the supply pins, route the inverting feedback path away from high-current switching nodes, and confirm output swing, input common-mode range, stability, and output-current requirements against the application before production release.
This page combines device identification, package and pin information, drop-in replacement analysis, application-focused guidance, and practical PCB design notes to support component selection, schematic review, sourcing, and second-source qualification.
Drop-in alternatifler için LM2904WHDT — aynı paket, pin-başına uyumlu. PCB yeniden montajı gerektiren farklı paket bileşenleri dışlanmıştır.
Bu Serideki Variantlar
Yedek parça uyumlu olan aynı serideki modeller LM2904WHDT (aynı form faktörü ve ayağa oturma) — farklı olan Package.
LM2904WDT
✅ Yerleştirme📋 Katalogda Olmayan Referans Alternatifi
LM2904DR
✅ YerleştirmeFiyat için iletişime geçin
Veri Şablonunu Görüntüle →LM2904DR
✅ YerleştirmeFiyat için iletişime geçin
Veri Şablonunu Görüntüle →LM2904DR
✅ YerleştirmeFiyat için iletişime geçin
Veri Şablonunu Görüntüle →LM2904DR
✅ YerleştirmeFiyat için iletişime geçin
Veri Şablonunu Görüntüle →LM2904DR
✅ YerleştirmeFiyat için iletişime geçin
Veri Şablonunu Görüntüle →LM2904WHDT Maksimum Değerlendirmeler & Elektriksel Özellikler
| Amplifier Count | 2 channels |
| Product Type | Dual general-purpose operational amplifier |
| Çıkış Türü | Single-ended |
| Number of Amplifiers | 2 |
| Supply Type | Single supply |
| Frequency Compensation | Internal |
| Architecture | Two independent voltage-feedback amplifiers |
| Paket | 8-SOIC |
| Pin Sayısı | 8 pins |
| Montaj Türü | Surface mount |
| Supplier Packaging | Tape and reel |
LM2904WHDT Pin Yapısı
| Pin 1 | OUT1 — Amplifier 1 output |
| Pin 2 | -IN1 — Amplifier 1 inverting input |
| Pin 3 | +IN1 — Amplifier 1 non-inverting input |
| Pin 4 | V- — Negative supply connection |
| Pin 5 | +IN2 — Amplifier 2 non-inverting input |
| Pin 6 | -IN2 — Amplifier 2 inverting input |
| Pin 7 | OUT2 — Amplifier 2 output |
| Pin 8 | V+ — Positive supply connection |
Tipik Uygulamalar
LM2904WHDT için uygundur 6 uygulamas: Automotive Sensor Conditioning, Industrial Transducer Interface, Motor Feedback Control, Audio Preamplifier Stage, Active Filter and Integrator, Portable Low-Power Control Board.
Automotive Sensor Conditioning
The LM2904WHDT fits two-channel sensor-conditioning stages because it combines 2 independent, internally compensated amplifiers in one 8-SOIC package. One channel can amplify or buffer a sensor output while the second channel supports reference comparison or feedback control. The low-power, single-supply architecture is appropriate for distributed automotive electronics where component count and board area matter. STMicroelectronics identifies automotive control systems as an intended application. Before releasing the design, verify the exact automotive qualification status, input common-mode range, output swing, offset voltage, and temperature limits against the sensor and vehicle electrical environment.
Önerilen
Industrial Transducer Interface
The LM2904WHDT can provide two stages of low-frequency signal conditioning for industrial pressure, position, and temperature transducers. Its 2 independent amplifier channels allow one channel to buffer the transducer while the other applies gain, inversion, or level shifting within the input common-mode range. Internal frequency compensation simplifies conventional feedback networks and can reduce the number of external components. The STMicroelectronics product documentation identifies industrial control systems as an application. Confirm supply voltage, signal bandwidth, output loading, offset accuracy, noise, and the final controller input range before selecting the device.
Önerilen
Motor Feedback Control
The LM2904WHDT is suitable for low-frequency current or position feedback around industrial and automotive motor-control systems. Its 2 amplifier channels can be assigned to a sensing amplifier and a driver-feedback stage, reducing the number of packages on the controller PCB. Single-ended outputs are convenient for connections to a controller input or comparator. Internal frequency compensation supports standard closed-loop configurations, while the low-power single-supply operation aligns with distributed control electronics. Keep feedback traces short and away from motor-switching nodes, and verify bandwidth, output swing, common-mode range, and response under the expected motor-load conditions.
Önerilen
Audio Preamplifier Stage
The LM2904WHDT can implement two low-frequency audio preamplifier or mixing channels in an 8-SOIC package. Internal frequency compensation makes each channel suitable for conventional inverting or non-inverting feedback networks, while single-ended outputs simplify connection to a line stage or analog measurement circuit. The dual configuration reduces duplicated package count compared with two single amplifiers. Audio performance still depends on the complete circuit, so evaluate the device's offset, gain-bandwidth, slew rate, output swing, noise, and load behavior against the source impedance and required signal bandwidth before production use.
Önerilen
Active Filter and Integrator
The LM2904WHDT's 2 internally compensated amplifier channels can implement a second-order active filter, a low-frequency integrator, or a combined filtering and sensing arrangement. Internal compensation removes the need for a separate compensation capacitor in conventional feedback networks, helping reduce component count. This is useful in industrial measurement and control boards where analog signals must be filtered before conversion or comparison. Select feedback and passive values using the manufacturer's stability and frequency-response guidance. Verify input common-mode limits, output swing, slew rate, and the accuracy of external resistors and capacitors across the required temperature range.
Önerilen
Portable Low-Power Control Board
The LM2904WHDT suits portable and distributed control equipment because it provides 2 amplifier channels from a single low-power supply in one compact 8-SOIC package. A channel can buffer a sensor or control a comparator input, while the second handles feedback or an auxiliary interface. The internal frequency compensation and single-ended outputs help reduce board complexity. Power efficiency depends on the chosen supply voltage and operating point, so compare the device's documented supply current with the system duty cycle. Also verify input and output voltage limits, source impedance, noise requirements, and startup behavior before integrating it into a battery-operated design.
Önerilen
Önerilen Ürünler Özeti
Mühendislik referans verileri: LM2904WHDT — karşılaştırma, tasarım rehberi ve uyumluluk bilgileri.
Seçim Kılavuzu
Alternatiflerle Karşılaştırma
| Parametre | Bu Ürün | LM2904WDT | LM2904 | LM2904 | LM2904 | LM2904 | LM2904 |
|---|---|---|---|---|---|---|---|
| Brand | STMicroelectronics | Texas Instruments | Renesas Electronics | Analog Devices | Burr-Brown | Philips | Toshiba |
| Package | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC |
| Amplifier Count | 2 | 2 | 2 | 2 | 2 | 2 | 2 |
| Product Category | General-purpose operational amplifier | General-purpose operational amplifier | General-purpose operational amplifier | General-purpose operational amplifier | General-purpose operational amplifier | General-purpose operational amplifier | General-purpose operational amplifier |
| Output Type | Single-ended | Single-ended | Single-ended | Single-ended | Single-ended | Single-ended | Single-ended |
| Supply Configuration | Single supply | Single supply | Single supply | Single supply | Single supply | Single supply | Single supply |
| Frequency Compensation | Internal | Internal | Internal | Internal | Internal | Internal | Internal |
Ana Farklılayıcılar
- Two independent channels in one compact package (karşılaştırma:LM2904WDT)
- Single-supply operation aligned with industrial control designs (karşılaştırma:LM2904)
- Internal frequency compensation reduces external circuitry (karşılaştırma:LM2902VDG)
Tasarım Notları
Place the primary supply bypass capacitor directly between pins 8 (V+) and 4 (V−), with the ground-side connection following a short, low-impedance path to the supply-reference plane. Keep each amplifier's feedback components close to their associated input and output pins. Route the two channels separately when one channel carries a high-level signal and the other handles a sensitive low-level input.
Keep inverting-input and feedback tracks away from switching-node copper, motor windings, inductors, and high-current return paths. A grounded or continuous reference plane helps reduce coupling, but do not interrupt plane current paths to create isolation. For automotive or industrial control boards, keep the analog amplifier area separated from high-switching-current sections and maintain controlled grounding around the 8-SOIC footprint.
Do not treat the 8-SOIC footprint alone as proof of electrical equivalence. Before replacing LM2904WHDT, compare supply range, input common-mode range, output swing, input offset, bandwidth, slew rate, output-current capability, and operating temperature. Also confirm the manufacturer-specific ordering suffix, reel format, and pin orientation because similar dual-amplifier packages may use different exposed-pad or thermal arrangements.
For sensor inputs, keep source impedance and leakage in mind because they can combine with input bias current to create offset and noise. Use the shortest practical input route and place any input filtering capacitor close to the amplifier input. When both channels amplify fast signals, check channel-to-channel coupling through shared supply impedance and use local bypass capacitance rather than relying only on bulk filtering.
Uyumluluk Bilgisi
The product documentation identifies automotive and industrial control applications, but no explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declaration was identified for this ordering code.