LM2904WHDT - Dual Low-Power Op Amp, 8-SOIC | STMicroelectronics
MPN: LM2904WHDT ✓ 啟用中LM2904WHDT 概覽
An operational amplifier is a voltage-feedback amplifier that uses high open-loop gain to amplify the difference between its inverting and non-inverting inputs. The LM2904 belongs to the operational-amplifier hierarchy, which sits within analog and mixed-signal semiconductors. Its dual-channel configuration reduces component count and board area when two amplifier functions are required on the same PCB.
Key features include 2 amplifier channels in one package, internal frequency compensation, and low-power operation from a single supply. The internal compensation removes the need for an external dominant-pole capacitor in conventional closed-loop applications. Single-ended outputs also simplify connection to analog-to-digital converters, sensors, transducers, and controller inputs that require a grounded-reference signal.
The architecture is suited to low-frequency precision-control applications because each channel has independent signal inputs. Designers can configure each amplifier as a voltage follower, non-inverting amplifier, or inverting amplifier. Unity-gain stability is especially useful for direct sensing and impedance-buffering positions where adding feedback components would be undesirable.
Typical uses include automotive sensor interfaces, industrial transducers, motor-control feedback networks, audio preamplifier stages, and low-frequency active filters. The STMicroelectronics product description identifies automotive and industrial control systems as primary application areas, while the low-power architecture benefits portable or distributed equipment operating from a single supply.
When assigning PCB tracks, use the manufacturer pin-description table and preserve the standard SOIC-8 pin sequence. Place each bypass capacitor close to the supply pins, route the inverting feedback path away from high-current switching nodes, and confirm output swing, input common-mode range, stability, and output-current requirements against the application before production release.
This page combines device identification, package and pin information, drop-in replacement analysis, application-focused guidance, and practical PCB design notes to support component selection, schematic review, sourcing, and second-source qualification.
直接替換替代品,適用於 LM2904WHDT — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: LM2904WHDT (相同外形與佔位) — 差異在於 Package.
LM2904WDT
✅ 直接替換📋 參考替代品(不在目錄中)
LM2904DR
✅ 直接替換聯絡詢價
查看資料表 →LM2904DR
✅ 直接替換聯絡詢價
查看資料表 →LM2904DR
✅ 直接替換聯絡詢價
查看資料表 →LM2904WHDT 最大額定值與電氣特性
| Amplifier Count | 2 channels |
| Product Type | Dual general-purpose operational amplifier |
| 輸出類型 | Single-ended |
| Number of Amplifiers | 2 |
| Supply Type | Single supply |
| Frequency Compensation | Internal |
| Architecture | Two independent voltage-feedback amplifiers |
| 封裝 | 8-SOIC |
| 腳位數 | 8 pins |
| 安裝類型 | Surface mount |
| Supplier Packaging | Tape and reel |
LM2904WHDT 腳位配置
| 腳位 1 | OUT1 — Amplifier 1 output |
| 腳位 2 | -IN1 — Amplifier 1 inverting input |
| 腳位 3 | +IN1 — Amplifier 1 non-inverting input |
| 腳位 4 | V- — Negative supply connection |
| 腳位 5 | +IN2 — Amplifier 2 non-inverting input |
| 腳位 6 | -IN2 — Amplifier 2 inverting input |
| 腳位 7 | OUT2 — Amplifier 2 output |
| 腳位 8 | V+ — Positive supply connection |
典型應用
LM2904WHDT 適用於 6 應用s: Automotive Sensor Conditioning, Industrial Transducer Interface, Motor Feedback Control, Audio Preamplifier Stage, Active Filter and Integrator, Portable Low-Power Control Board.
Automotive Sensor Conditioning
The LM2904WHDT fits two-channel sensor-conditioning stages because it combines 2 independent, internally compensated amplifiers in one 8-SOIC package. One channel can amplify or buffer a sensor output while the second channel supports reference comparison or feedback control. The low-power, single-supply architecture is appropriate for distributed automotive electronics where component count and board area matter. STMicroelectronics identifies automotive control systems as an intended application. Before releasing the design, verify the exact automotive qualification status, input common-mode range, output swing, offset voltage, and temperature limits against the sensor and vehicle electrical environment.
推薦
Industrial Transducer Interface
The LM2904WHDT can provide two stages of low-frequency signal conditioning for industrial pressure, position, and temperature transducers. Its 2 independent amplifier channels allow one channel to buffer the transducer while the other applies gain, inversion, or level shifting within the input common-mode range. Internal frequency compensation simplifies conventional feedback networks and can reduce the number of external components. The STMicroelectronics product documentation identifies industrial control systems as an application. Confirm supply voltage, signal bandwidth, output loading, offset accuracy, noise, and the final controller input range before selecting the device.
推薦
Motor Feedback Control
The LM2904WHDT is suitable for low-frequency current or position feedback around industrial and automotive motor-control systems. Its 2 amplifier channels can be assigned to a sensing amplifier and a driver-feedback stage, reducing the number of packages on the controller PCB. Single-ended outputs are convenient for connections to a controller input or comparator. Internal frequency compensation supports standard closed-loop configurations, while the low-power single-supply operation aligns with distributed control electronics. Keep feedback traces short and away from motor-switching nodes, and verify bandwidth, output swing, common-mode range, and response under the expected motor-load conditions.
推薦
Audio Preamplifier Stage
The LM2904WHDT can implement two low-frequency audio preamplifier or mixing channels in an 8-SOIC package. Internal frequency compensation makes each channel suitable for conventional inverting or non-inverting feedback networks, while single-ended outputs simplify connection to a line stage or analog measurement circuit. The dual configuration reduces duplicated package count compared with two single amplifiers. Audio performance still depends on the complete circuit, so evaluate the device's offset, gain-bandwidth, slew rate, output swing, noise, and load behavior against the source impedance and required signal bandwidth before production use.
推薦
Active Filter and Integrator
The LM2904WHDT's 2 internally compensated amplifier channels can implement a second-order active filter, a low-frequency integrator, or a combined filtering and sensing arrangement. Internal compensation removes the need for a separate compensation capacitor in conventional feedback networks, helping reduce component count. This is useful in industrial measurement and control boards where analog signals must be filtered before conversion or comparison. Select feedback and passive values using the manufacturer's stability and frequency-response guidance. Verify input common-mode limits, output swing, slew rate, and the accuracy of external resistors and capacitors across the required temperature range.
推薦
Portable Low-Power Control Board
The LM2904WHDT suits portable and distributed control equipment because it provides 2 amplifier channels from a single low-power supply in one compact 8-SOIC package. A channel can buffer a sensor or control a comparator input, while the second handles feedback or an auxiliary interface. The internal frequency compensation and single-ended outputs help reduce board complexity. Power efficiency depends on the chosen supply voltage and operating point, so compare the device's documented supply current with the system duty cycle. Also verify input and output voltage limits, source impedance, noise requirements, and startup behavior before integrating it into a battery-operated design.
推薦
推薦產品摘要
工程參考資料,適用於 LM2904WHDT — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | LM2904WDT | LM2904 | LM2904 | LM2904 | LM2904 | LM2904 |
|---|---|---|---|---|---|---|---|
| Brand | STMicroelectronics | Texas Instruments | Renesas Electronics | Analog Devices | Burr-Brown | Philips | Toshiba |
| Package | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC |
| Amplifier Count | 2 | 2 | 2 | 2 | 2 | 2 | 2 |
| Product Category | General-purpose operational amplifier | General-purpose operational amplifier | General-purpose operational amplifier | General-purpose operational amplifier | General-purpose operational amplifier | General-purpose operational amplifier | General-purpose operational amplifier |
| Output Type | Single-ended | Single-ended | Single-ended | Single-ended | Single-ended | Single-ended | Single-ended |
| Supply Configuration | Single supply | Single supply | Single supply | Single supply | Single supply | Single supply | Single supply |
| Frequency Compensation | Internal | Internal | Internal | Internal | Internal | Internal | Internal |
主要差異化特點
- Two independent channels in one compact package (對比LM2904WDT)
- Single-supply operation aligned with industrial control designs (對比LM2904)
- Internal frequency compensation reduces external circuitry (對比LM2902VDG)
設計說明
Place the primary supply bypass capacitor directly between pins 8 (V+) and 4 (V−), with the ground-side connection following a short, low-impedance path to the supply-reference plane. Keep each amplifier's feedback components close to their associated input and output pins. Route the two channels separately when one channel carries a high-level signal and the other handles a sensitive low-level input.
Keep inverting-input and feedback tracks away from switching-node copper, motor windings, inductors, and high-current return paths. A grounded or continuous reference plane helps reduce coupling, but do not interrupt plane current paths to create isolation. For automotive or industrial control boards, keep the analog amplifier area separated from high-switching-current sections and maintain controlled grounding around the 8-SOIC footprint.
Do not treat the 8-SOIC footprint alone as proof of electrical equivalence. Before replacing LM2904WHDT, compare supply range, input common-mode range, output swing, input offset, bandwidth, slew rate, output-current capability, and operating temperature. Also confirm the manufacturer-specific ordering suffix, reel format, and pin orientation because similar dual-amplifier packages may use different exposed-pad or thermal arrangements.
For sensor inputs, keep source impedance and leakage in mind because they can combine with input bias current to create offset and noise. Use the shortest practical input route and place any input filtering capacitor close to the amplifier input. When both channels amplify fast signals, check channel-to-channel coupling through shared supply impedance and use local bypass capacitance rather than relying only on bulk filtering.
合規資訊
The product documentation identifies automotive and industrial control applications, but no explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declaration was identified for this ordering code.