Analog Devices

ADM3485EAR - 12 Mbps 3.3 V RS-485 Transceiver | Analog Devices

MPN: ADM3485EAR ✓ فعال
3.3 V Vdss 8-pin SOIC Package
MOQ: 1 |

ADM3485EAR جائزہ

The Analog Devices ADM3485EAR is a 3.3 V, low-power RS-485/RS-422 half-duplex transceiver rated for data rates up to 12 Mbps, with ±15 kV ESD protection on the RS-485 input and output pins. The device is packaged in an 8-pin SOIC and supports balanced differential communication on multipoint bus transmission lines. One transmitter and one receiver are integrated into each package, allowing a compact two-wire industrial communications interface.

An RS-485 transceiver is an interface IC that converts logic-level serial data into balanced differential signals for reliable communication over longer cables and noisy environments. The corresponding receiver converts differential bus voltage back into a logic-level signal. Together, these devices form the physical-layer link between a controller and remote nodes, with RS-422 providing balanced point-to-point signaling and RS-485 supporting multipoint buses.

Key features include TIA/EIA RS-485 and RS-422 compliance, a maximum data rate of 12 Mbps, ±15 kV ESD protection, and operation on a single 3.3 V supply. The half-duplex configuration shares the driver and receiver bus connections, reducing board area and external switching requirements. A fail-safe receiver is designed to provide a defined output when the bus is open-circuit, while the low-power shutdown function supports systems that need to reduce consumption when the interface is inactive.

The ADM3485E family combines a low-power 3.3 V architecture with high-speed differential signaling. Its 12 Mbps capability suits short-distance, high-speed industrial links, while multipoint operation accommodates systems with as many as 32 nodes. The 8-pin SOIC package supports conventional surface-mount assembly, and the same compact footprint simplifies comparison with other 8-pin half-duplex line transceivers.

Typical uses include industrial control networks, factory automation equipment, instrumentation, motor-control subsystems, and embedded serial buses. The device can also serve as a robust physical-layer interface between a host controller and remotely located sensors, actuators, or data-acquisition modules where 3.3 V logic levels and multidrop capability are required.

Designers should preserve the transceiver's common-mode range and termination requirements when laying out the bus. Place the differential line pair with continuous ground reference, route the pair as a coupled transmission-line structure, and position termination only at designated bus endpoints. Add suitable surge protection and verify that system grounding and cable length remain compatible with the operating data rate.

This page combines electrical characteristics, package details, application guidance, parameter comparisons, and verified drop-in alternatives. It also highlights design trade-offs involving data rate, bus direction control, ESD protection, termination, and multipoint operation so engineers can select the correct interface IC before layout begins.

کے لیے ڈراپ اِن متبادل ADM3485EAR — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔

اس سیریز میں مختلف ورژن

اسی سیریز کے ماڈلز جو ڈراپ اِن مطابقت رکھتے ہیں ADM3485EAR (یکساں فارم فیکٹر اور فٹ پرنٹ) — میں مختلف Package, Bus Configuration, Low-Power Operation, Duplex Mode, Data Rate.

Analog Devices
Bus Configuration: Multipoint bus transmission
Low-Power Operation: Yes
موازنہ کریں ADM3485EAR →
Analog Devices
Package: 14-pin SOIC, 3.90 mm width
Bus Configuration: Multipoint bus transmission line
Low-Power Operation: Low-power transceiver with shutdown mode
موازنہ کریں ADM3485EAR →
MaxLinear
Package: 8-SOIC
Low-Power Operation: Low-power family specification
Data Rate: 10 Mbps
موازنہ کریں ADM3485EAR →

ADM3485EARZ

✅ ڈراپ-اِن
Analog Devices
📦 8-SOIC
RS-485/RS-422 differential line transceiver · 3.3 V · 12 Mbps · ±15 kV · Half-duplex · EIA RS-485 and TIA/EIA RS-422 · Multipoint bus transmission · Yes

قیمت کے لیے رابطہ کریں

ڈیٹا شیٹ دیکھیں →

ADM3483EARZ

✅ ڈراپ-اِن
📦 8-SOIC
Uses the same 8-SOIC RS-485/RS-422 family footprint and 3.3 V interface; data-rate and enable details must be confirmed because they differ from the 12 Mbps ADM3485EAR

📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)

ADM3491EARZ

✅ ڈراپ-اِن
Analog Devices
📦 8-SOIC
3.3 V · TIA/EIA RS-485 and TIA/EIA RS-422 · 1 transmitter and 1 receiver · Full duplex · 12 Mbps · ±15 kV · Low-power transceiver with shutdown mode · Single +3.3 V supply

قیمت کے لیے رابطہ کریں

ڈیٹا شیٹ دیکھیں →

ST3485ECDR

✅ ڈراپ-اِن
📦 8-SOIC
Matches the 3.3 V, 12 Mbps minimum, half-duplex RS-485/RS-422 function; driver loading, shutdown current, ESD rating, and enable polarity may differ

📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)

SP3485EN-L

✅ ڈراپ-اِن
MaxLinear
📦 8-SOIC
RS-485/RS-422 half-duplex transceiver · 3.135 V to 3.465 V · 3.3 V · 10 Mbps · 1 · 1 · Half-duplex · RS-485 and RS-422

قیمت کے لیے رابطہ کریں

ڈیٹا شیٹ دیکھیں →

ADM3485EAR تفصیلات

سپلائی وولٹیج 3.3 V
ڈیٹا ریٹ 12 Mbps
ESD Protection ±15 kV
Protocol Support TIA/EIA RS-485 and RS-422
Duplex Mode Half-duplex
Driver Count 1 driver
Receiver Count 1 receiver
Maximum Bus Nodes 32 nodes
Receiver Fail-Safe Behavior Open-circuit fail-safe design
Low-Power Shutdown Supported
Bus Configuration Multipoint differential bus
پیکیج 8-pin SOIC
ماؤنٹنگ ٹائپ Surface mount

ADM3485EAR 8-pin soic پن کنفیگریشن گائیڈ

ADM3485EAR (8-pin soic پیکیج) کے لیے پن کنفیگریشن۔ پن نمبرنگ، فنکشنز اور کنکشن ڈایاگرامز مینوفیکچرر کے ڈیٹا شیٹ میں بیان کیے گئے ہیں۔ درست فٹ پرنٹ اور سولڈرنگ رہنما ہدایات کے لیے اسی سے رجوع کریں۔

ADM3485EAR کے لیے 8-pin soic پیکیج پن آؤٹ ڈایاگرام

کے لیے تفصیلی پن آؤٹ ڈیٹا دستیاب نہیں ADM3485EAR.

رجوع کریں ڈیٹا شیٹ مکمل پن کنفیگریشن کے لیے۔

عام استعمالات

ADM3485EAR کے لیے موزوں ہے 6 ایپلیکیشنs: Industrial Automation Bus Interface, Data Acquisition and Instrumentation, Motor and actuator Control Networks, Building Access and Security Equipment, Embedded Sensor and Actuator Networks, Test and Measurement Equipment.

🏭

Industrial Automation Bus Interface

The ADM3485EAR fits factory automation links that need balanced differential signaling from a 3.3 V controller. Place the transceiver between the host UART and a multidrop RS-485 bus, using its integrated half-duplex driver and receiver to support a data rate of up to 12 Mbps. The ±15 kV ESD protection improves resilience at connector-exposed equipment interfaces, while the fail-safe open-circuit receiver behavior helps establish a defined logic state on an idle or broken bus.

🔧

Data Acquisition and Instrumentation

The ADM3485EAR provides a compact physical-layer interface between instrumentation controllers and remotely located measurement modules. Its 3.3 V supply operation suits modern mixed-signal systems, and the 12 Mbps rate allows short, high-speed links carrying command, configuration, and measurement traffic. Balanced differential signaling reduces susceptibility to common-mode noise present near motors, relays, and switching power converters. The 8-pin SOIC footprint also keeps the interface compact beside an ADC or microcontroller.

⚡

Motor and actuator Control Networks

The ADM3485EAR is suitable for communication links between a controller and motor-drive or actuator modules installed away from the main board. Its half-duplex architecture uses one bidirectional differential pair, reducing wiring in multipoint networks, while the receiver's fail-safe design helps manage open-circuit conditions. The 12 Mbps capability supports high-rate command traffic over appropriately short cables, and ±15 kV ESD protection adds useful robustness where cables connect through industrial connectors.

🎥

Building Access and Security Equipment

The ADM3485EAR can connect access-control panels, card readers, and distributed security modules over a 3.3 V RS-485 network. Differential signaling supports reliable communication where cable runs pass near elevators, lighting equipment, or other electrically noisy systems. The multipoint capability permits as many as 32 nodes, and the low-power shutdown function helps conserve energy in intermittently used peripheral devices. System designers should maintain a continuous ground reference and use endpoint termination.

🧩

Embedded Sensor and Actuator Networks

The ADM3485EAR provides a practical interface for embedded controllers communicating with distributed sensors and actuators over a short cable. Its 3.3 V operation minimizes level-shifting requirements when paired with modern microcontrollers, while one driver and one receiver support a compact half-duplex topology. At rates up to 12 Mbps, the device can support responsive command and status traffic, subject to distance, cable attenuation, node loading, and termination constraints.

📱

Test and Measurement Equipment

The ADM3485EAR is appropriate for laboratory and production-test equipment that communicates with remote fixtures or instrument modules. Its balanced differential interface helps maintain data integrity across cable connections that may share space with switching supplies and digital clocks. The 8-pin SOIC package simplifies compact instrument designs, while half-duplex control supports shared two-wire buses. For high-throughput test systems, use controlled impedance and endpoint termination to preserve the advertised 12 Mbps capability.

What is the operating voltage of ADM3485EAR?
The ADM3485EAR operates from a single 3.3 V supply and is designed for low-power differential line communication. According to the Analog Devices ADM3485E datasheet, the device integrates one transmitter and one receiver in a half-duplex configuration. Its minimum and maximum supply-voltage limits should be checked in the manufacturer's recommended operating-conditions table before final circuit release.
What data rate does ADM3485EAR support?
The ADM3485EAR supports data rates up to 12 Mbps. The Analog Devices ADM3485E datasheet identifies the device as a 3.3 V, low-power half-duplex transceiver for RS-485 and RS-422 links. This bandwidth is appropriate for short cables and high-speed equipment links, although actual distance and signaling margin depend on cable characteristics, termination, topology, and data pattern.
Does ADM3485EAR provide RS-485 ESD protection?
Yes, the ADM3485EAR provides ±15 kV ESD protection on the RS-485 input and output pins. The Analog Devices ADM3485E datasheet identifies this protection as a principal feature of the family. It improves resilience to electrostatic discharge at externally accessible connectors, although cable routing, grounding, and additional surge protection must still be evaluated for the completed system.
Is ADM3485EAR RS-422 or RS-485 compatible?
The ADM3485EAR is compatible with both TIA/EIA RS-422 and RS-485 operation. The Analog Devices ADM3485E datasheet describes the family as a balanced-data transceiver for multipoint bus transmission lines. Half-duplex operation suits a shared RS-485 pair, while the balanced transmitter and receiver also support compatible point-to-point RS-422 implementations.
How many nodes can be connected to an ADM3485EAR bus?
An ADM3485EAR RS-485 bus can support up to 32 nodes. The Analog Devices ADM3485E datasheet lists this figure among the device characteristics. System-level loading, cable impedance, termination, grounding, and the attached receiver and driver impedances must also remain within the limits required for reliable multipoint communication.
Where can I download the ADM3485EAR datasheet PDF?
The official ADM3485E documentation is accessible from the Analog Devices product page at https://www.analog.com/en/products/adm3485e.html. Use the manufacturer's Data Sheet link for the authoritative electrical characteristics, pin description, typical performance plots, and application information. The ADM3485EAR ordering code identifies the 8-pin SOIC member of the ADM3485E family.
Where can I find the ADM3485EAR pinout?
The ADM3485EAR pinout is shown in the Pin Configuration and Pin Description sections of the Analog Devices ADM3485E datasheet. The device uses an 8-pin SOIC package and includes differential driver outputs, differential receiver inputs, receiver-enable and driver-enable controls, power, and ground connections. Use the manufacturer diagram when assigning PCB tracks to avoid confusing complementary enable polarity.
Is ADM3485EAR suitable for industrial automation systems?
The ADM3485EAR is well suited to industrial automation links that require 3.3 V logic, balanced signaling, and multidrop RS-485 communication. Its 12 Mbps maximum data rate, ±15 kV ESD protection, fail-safe receiver design, and support for up to 32 nodes address several practical bus requirements. Cable length and data rate must still be balanced to maintain reliable signal integrity.
What can replace the ADM3485EAR on the same PCB?
The ADM3485EAR can be replaced by a pin-compatible 3.3 V, 8-pin SOIC RS-485/RS-422 half-duplex transceiver whose enable polarity, supply limits, bus loading, and data-rate ratings satisfy the design. ADM3485EARZ, ADM3483EARZ, ADM3491EARZ, ST3485ECDR, and SP3485EN-L are listed candidates, but each should be checked against the complete manufacturer datasheet before substitution.
Can ST3485ECDR replace ADM3485EAR?
The ST3485ECDR is a candidate replacement for the ADM3485EAR because it is also a 3.3 V, low-power, half-duplex RS-485 and RS-422 transceiver with a guaranteed data rate of at least 12 Mbps. Pin and enable-polarity compatibility must still be confirmed from the STMicroelectronics datasheet. Check bus impedance, shutdown behavior, ESD rating, and supply tolerances before approving a board revision.
ADM3485EAR vs ST3485ECDR: which is better for an industrial link?
The ADM3485EAR and ST3485ECDR both support 3.3 V, half-duplex RS-485 and RS-422 communication at 12 Mbps or more. Selection should depend on verified enable polarity, pinout, driver and receiver loading, shutdown current, ESD rating, operating-temperature range, and lifecycle status rather than headline speed alone. The cross-reference information supports both as candidates, but final qualification requires a full manufacturer-datasheet comparison.
When should I choose ADM3485EAR over ADM3485EARZ?
Choose ADM3485EAR when its ordering, temperature, compliance, and lifecycle characteristics match the production requirement; choose ADM3485EARZ when that ordering suffix is required for a specific regulatory or supply-chain requirement. Both are 8-pin SOIC RS-485 and RS-422 devices, so confirm the exact suffix against the Analog Devices ordering guide before treating them as interchangeable.
What is the best cross-brand equivalent for ADM3485EAR?
The ST3485ECDR is the strongest cross-brand candidate shown for the ADM3485EAR because both are 3.3 V, half-duplex RS-485 and RS-422 transceivers, and the ST3485ECDR guarantees at least 12 Mbps. It is only a qualified drop-in candidate after checking pinout, enable polarity, electrical loading, shutdown state, and package details against both manufacturers' datasheets.
What are the key specifications of ADM3485EAR that engineers should know?
The ADM3485EAR is a 3.3 V, 12 Mbps, half-duplex RS-485 and RS-422 transceiver in an 8-pin SOIC package. According to the Analog Devices ADM3485E datasheet, it provides one driver, one receiver, ±15 kV ESD protection, fail-safe open-circuit receiver behavior, low-power shutdown, and support for as many as 32 bus nodes.
Where to buy ADM3485EAR online?
Use the Request a Quote form on this page to request ADM3485EAR availability, unit pricing, minimum order quantity, and lead time for your required packaging and quantity. The live quote channel confirms commercial terms for the exact 8-pin SOIC ordering code and avoids returning an incorrect price for a different suffix, temperature grade, or reel configuration.
What is the lead time for ADM3485EAR?
The current lead time for ADM3485EAR depends on order quantity, manufacturing status, and the packaging variant required. Submit a Request a Quote on this page with your target quantity, date code preference, and shipment destination. The manufacturer lists the ADM3485E as a current family, but a production commitment should be confirmed for the exact order code.

کے لیے انجینئرنگ ریفرنس ڈیٹا ADM3485EAR — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔

انتخاب کی گائیڈ

Choose the ADM3485EAR for a compact 3.3 V RS-485 or RS-422 interface that requires up to 12 Mbps, one driver, one receiver, ±15 kV ESD protection, and a half-duplex 8-pin SOIC implementation. ADM3485EARZ is the closest same-brand ordering alternative when its exact suffix satisfies production and compliance requirements. ADM3483EARZ and ADM3491EARZ may suit designs needing a related Analog Devices transceiver, but their data-rate, enable, shutdown, and loading details must be checked before replacement. ST3485ECDR is a strong cross-brand candidate because it shares the 3.3 V, half-duplex, and minimum-12-Mbps classes. SP3485EN-L is another candidate with the same package and protocol class, but exact pin behavior and speed should be confirmed. For any substitution, prioritize enable polarity, common-mode range, bus impedance, ESD rating, temperature range, and lifecycle status rather than relying only on headline data rate.

متبادلات کے ساتھ موازنہ

پیرامیٹر یہ پروڈکٹ ADM3485EARZ ADM3483EARZ ADM3491EARZ ST3485ECDR SP3485EN-L
Brand Analog Devices Analog Devices Analog Devices Analog Devices STMicroelectronics Exar
Package 8-SOIC 8-SOIC 8-SOIC 8-SOIC 8-SOIC 8-SOIC
Supply Voltage 3.3 V 3.3 V 3.3 V 3.3 V 3.3 V 3.3 V
Protocols RS-485 and RS-422 RS-485 and RS-422 RS-485 and RS-422 RS-485 and RS-422 RS-485 and RS-422 RS-485 and RS-422

اہم امتیازی خصوصیات

  • High-speed 3.3 V operation (بمقابلہSP3485EN-L)
  • Clearly documented ESD protection (بمقابلہST3485ECDR)
  • Multipoint fail-safe receiver design (بمقابلہADM3491EARZ)
  • Direct same-brand ordering alternative (بمقابلہADM3485EARZ)

ڈیزائن نوٹس

Route the RS-485 and RS-422 differential pair as a controlled-impedance transmission line with continuous ground reference. Keep the driver and receiver connections away from switching-node traces and maintain consistent spacing between the pair. Place bypass capacitance close to the 3.3 V and ground pins, and keep the connector-side protection and termination components close to the entry point where transient energy first enters the board.

Do not enable the driver while the receiver remains active on the same bus unless the transceiver datasheet explicitly permits that state. A half-duplex RS-485 node commonly needs coordinated driver-enable and receiver-enable control so the driver does not contend with another transmitter. Validate the enable polarity, startup sequence, and bus idle condition in firmware before releasing the transceiver onto the network.

Terminate the differential bus only at the two physical endpoints, using the termination resistance specified by the Analog Devices ADM3485E datasheet and the impedance of the installed cable. Avoid placing termination across every node in a multidrop network. For long or high-speed links, calculate attenuation and reflection behavior, maintain a ground reference along the cable route, and consider fail-safe biasing only after confirming its effect on the complete network.

The 12 Mbps rating is not a guarantee that every cable length or topology supports that rate. Use shorter, properly terminated cables at the highest data rates, keep stub lengths short, and verify signal integrity with an oscilloscope in the installed enclosure. Also check the UART baud-rate tolerance and ensure that the host controller provides enough turnaround delay for the half-duplex bus.

تعمیل کی معلومات

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
لیڈ فری
Unknown
ہیلوجن فری
Unknown
کنفلیکٹ منرلز
Unknown

The ADM3485E is an industrial interface IC and is not presented as an AEC-Q100-qualified automotive device. Specific RoHS, REACH, lead-free, halogen-free, and conflict-minerals statements require confirmation for the exact ADM3485EAR ordering code.

ڈیٹا کی تصدیق کی تاریخ: 2026-11-14 — ڈیٹا XAIPART کی کمپوننٹ انجینئرنگ ٹیم کے ذریعے تصدیق شدہ اور ترتیب شدہ

متعلقہ تلاشیں

ADM3485EAR datasheet ADM3485EAR pinout ADM3485EAR datasheet pdf Analog Devices ADM3485EAR ADM3485EAR 12 Mbps ADM3485EAR 3.3V RS-485 ADM3485EAR 8-SOIC ADM3485EAR equivalent ADM3485EAR replacement ADM3485EAR cross reference ADM3485EAR vs ST3485ECDR ADM3485EAR application circuit ADM3485EAR price ADM3485EAR stock ADM3485EAR RS-485 transceiver

متعلقہ اجزاء اور اصطلاحات

Analog Devices ADM3485EAR ADM3485EARZ ADM3483EARZ ADM3491EARZ ST3485ECDR SP3485EN-L RS-485 transceiver RS-422 transceiver half-duplex transceiver differential line transceiver interface IC TIA/EIA RS-485 TIA/EIA RS-422 3.3 V power supply 12 Mbps data rate ±15 kV ESD protection multipoint bus fail-safe receiver 8-SOIC package QFN family surface mount industrial automation balanced differential signaling
فوری کوٹ RFQ
مکمل تفصیلات بھریں — ہماری سیلز ٹیم 24 گھنٹوں میں جواب دے گی
پارٹ نمبر مینوفیکچرر پیکج QTY ہدف قیمت کل رقم
✓
کوٹ جمع ہو گیا!

ہم 24 گھنٹوں کے اندر آپ کے ای میل کا جواب دیں گے

1
RFQ جمع ہو گیا
2
کوٹ موصول ہو گیا
3
آرڈر دے دیا گیا
4
ادائیگی
5
بھیج دیا گیا
6
ڈیلیور شدہ
RFQ تفصیلات دیکھیں