ADM3485EAR - 12 Mbps 3.3 V RS-485 Transceiver | Analog Devices
MPN: ADM3485EAR ✓ 啟用中ADM3485EAR 概覽
An RS-485 transceiver is an interface IC that converts logic-level serial data into balanced differential signals for reliable communication over longer cables and noisy environments. The corresponding receiver converts differential bus voltage back into a logic-level signal. Together, these devices form the physical-layer link between a controller and remote nodes, with RS-422 providing balanced point-to-point signaling and RS-485 supporting multipoint buses.
Key features include TIA/EIA RS-485 and RS-422 compliance, a maximum data rate of 12 Mbps, ±15 kV ESD protection, and operation on a single 3.3 V supply. The half-duplex configuration shares the driver and receiver bus connections, reducing board area and external switching requirements. A fail-safe receiver is designed to provide a defined output when the bus is open-circuit, while the low-power shutdown function supports systems that need to reduce consumption when the interface is inactive.
The ADM3485E family combines a low-power 3.3 V architecture with high-speed differential signaling. Its 12 Mbps capability suits short-distance, high-speed industrial links, while multipoint operation accommodates systems with as many as 32 nodes. The 8-pin SOIC package supports conventional surface-mount assembly, and the same compact footprint simplifies comparison with other 8-pin half-duplex line transceivers.
Typical uses include industrial control networks, factory automation equipment, instrumentation, motor-control subsystems, and embedded serial buses. The device can also serve as a robust physical-layer interface between a host controller and remotely located sensors, actuators, or data-acquisition modules where 3.3 V logic levels and multidrop capability are required.
Designers should preserve the transceiver's common-mode range and termination requirements when laying out the bus. Place the differential line pair with continuous ground reference, route the pair as a coupled transmission-line structure, and position termination only at designated bus endpoints. Add suitable surge protection and verify that system grounding and cable length remain compatible with the operating data rate.
This page combines electrical characteristics, package details, application guidance, parameter comparisons, and verified drop-in alternatives. It also highlights design trade-offs involving data rate, bus direction control, ESD protection, termination, and multipoint operation so engineers can select the correct interface IC before layout begins.
直接替換替代品,適用於 ADM3485EAR — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: ADM3485EAR (相同外形與佔位) — 差異在於 Package, Bus Configuration, Low-Power Operation, Duplex Mode, Data Rate.
ADM3485EARZ
✅ 直接替換聯絡詢價
查看資料表 →ADM3483EARZ
✅ 直接替換📋 參考替代品(不在目錄中)
ADM3491EARZ
✅ 直接替換聯絡詢價
查看資料表 →ST3485ECDR
✅ 直接替換📋 參考替代品(不在目錄中)
SP3485EN-L
✅ 直接替換聯絡詢價
查看資料表 →ADM3485EAR 規格
| 供應電壓 | 3.3 V |
| 資料速率 | 12 Mbps |
| ESD Protection | ±15 kV |
| Protocol Support | TIA/EIA RS-485 and RS-422 |
| Duplex Mode | Half-duplex |
| Driver Count | 1 driver |
| Receiver Count | 1 receiver |
| Maximum Bus Nodes | 32 nodes |
| Receiver Fail-Safe Behavior | Open-circuit fail-safe design |
| Low-Power Shutdown | Supported |
| Bus Configuration | Multipoint differential bus |
| 封裝 | 8-pin SOIC |
| 安裝類型 | Surface mount |
ADM3485EAR 8-pin soic 腳位配置指南
ADM3485EAR(8-pin soic 封裝)的腳位配置。 腳位編號、功能與連接圖定義於製造商資料手冊中。請參閱該手冊以取得確切的封裝尺寸與焊接指引。
無詳細腳位定義資料: ADM3485EAR.
請參閱 資料表 以查看完整腳位配置。
典型應用
ADM3485EAR 適用於 6 應用s: Industrial Automation Bus Interface, Data Acquisition and Instrumentation, Motor and actuator Control Networks, Building Access and Security Equipment, Embedded Sensor and Actuator Networks, Test and Measurement Equipment.
Industrial Automation Bus Interface
The ADM3485EAR fits factory automation links that need balanced differential signaling from a 3.3 V controller. Place the transceiver between the host UART and a multidrop RS-485 bus, using its integrated half-duplex driver and receiver to support a data rate of up to 12 Mbps. The ±15 kV ESD protection improves resilience at connector-exposed equipment interfaces, while the fail-safe open-circuit receiver behavior helps establish a defined logic state on an idle or broken bus.
推薦
Data Acquisition and Instrumentation
The ADM3485EAR provides a compact physical-layer interface between instrumentation controllers and remotely located measurement modules. Its 3.3 V supply operation suits modern mixed-signal systems, and the 12 Mbps rate allows short, high-speed links carrying command, configuration, and measurement traffic. Balanced differential signaling reduces susceptibility to common-mode noise present near motors, relays, and switching power converters. The 8-pin SOIC footprint also keeps the interface compact beside an ADC or microcontroller.
推薦
Motor and actuator Control Networks
The ADM3485EAR is suitable for communication links between a controller and motor-drive or actuator modules installed away from the main board. Its half-duplex architecture uses one bidirectional differential pair, reducing wiring in multipoint networks, while the receiver's fail-safe design helps manage open-circuit conditions. The 12 Mbps capability supports high-rate command traffic over appropriately short cables, and ±15 kV ESD protection adds useful robustness where cables connect through industrial connectors.
推薦
Building Access and Security Equipment
The ADM3485EAR can connect access-control panels, card readers, and distributed security modules over a 3.3 V RS-485 network. Differential signaling supports reliable communication where cable runs pass near elevators, lighting equipment, or other electrically noisy systems. The multipoint capability permits as many as 32 nodes, and the low-power shutdown function helps conserve energy in intermittently used peripheral devices. System designers should maintain a continuous ground reference and use endpoint termination.
推薦
Embedded Sensor and Actuator Networks
The ADM3485EAR provides a practical interface for embedded controllers communicating with distributed sensors and actuators over a short cable. Its 3.3 V operation minimizes level-shifting requirements when paired with modern microcontrollers, while one driver and one receiver support a compact half-duplex topology. At rates up to 12 Mbps, the device can support responsive command and status traffic, subject to distance, cable attenuation, node loading, and termination constraints.
推薦
Test and Measurement Equipment
The ADM3485EAR is appropriate for laboratory and production-test equipment that communicates with remote fixtures or instrument modules. Its balanced differential interface helps maintain data integrity across cable connections that may share space with switching supplies and digital clocks. The 8-pin SOIC package simplifies compact instrument designs, while half-duplex control supports shared two-wire buses. For high-throughput test systems, use controlled impedance and endpoint termination to preserve the advertised 12 Mbps capability.
推薦
推薦產品摘要
工程參考資料,適用於 ADM3485EAR — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | ADM3485EARZ | ADM3483EARZ | ADM3491EARZ | ST3485ECDR | SP3485EN-L |
|---|---|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | STMicroelectronics | Exar |
| Package | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC |
| Supply Voltage | 3.3 V | 3.3 V | 3.3 V | 3.3 V | 3.3 V | 3.3 V |
| Protocols | RS-485 and RS-422 | RS-485 and RS-422 | RS-485 and RS-422 | RS-485 and RS-422 | RS-485 and RS-422 | RS-485 and RS-422 |
主要差異化特點
- High-speed 3.3 V operation (對比SP3485EN-L)
- Clearly documented ESD protection (對比ST3485ECDR)
- Multipoint fail-safe receiver design (對比ADM3491EARZ)
- Direct same-brand ordering alternative (對比ADM3485EARZ)
設計說明
Route the RS-485 and RS-422 differential pair as a controlled-impedance transmission line with continuous ground reference. Keep the driver and receiver connections away from switching-node traces and maintain consistent spacing between the pair. Place bypass capacitance close to the 3.3 V and ground pins, and keep the connector-side protection and termination components close to the entry point where transient energy first enters the board.
Do not enable the driver while the receiver remains active on the same bus unless the transceiver datasheet explicitly permits that state. A half-duplex RS-485 node commonly needs coordinated driver-enable and receiver-enable control so the driver does not contend with another transmitter. Validate the enable polarity, startup sequence, and bus idle condition in firmware before releasing the transceiver onto the network.
Terminate the differential bus only at the two physical endpoints, using the termination resistance specified by the Analog Devices ADM3485E datasheet and the impedance of the installed cable. Avoid placing termination across every node in a multidrop network. For long or high-speed links, calculate attenuation and reflection behavior, maintain a ground reference along the cable route, and consider fail-safe biasing only after confirming its effect on the complete network.
The 12 Mbps rating is not a guarantee that every cable length or topology supports that rate. Use shorter, properly terminated cables at the highest data rates, keep stub lengths short, and verify signal integrity with an oscilloscope in the installed enclosure. Also check the UART baud-rate tolerance and ensure that the host controller provides enough turnaround delay for the half-duplex bus.
合規資訊
The ADM3485E is an industrial interface IC and is not presented as an AEC-Q100-qualified automotive device. Specific RoHS, REACH, lead-free, halogen-free, and conflict-minerals statements require confirmation for the exact ADM3485EAR ordering code.