ADM3485EAR - 12 Mbps 3.3 V RS-485 Transceiver | Analog Devices
MPN: ADM3485EAR ✓ Hoạt độngADM3485EAR Tóm tắt
An RS-485 transceiver is an interface IC that converts logic-level serial data into balanced differential signals for reliable communication over longer cables and noisy environments. The corresponding receiver converts differential bus voltage back into a logic-level signal. Together, these devices form the physical-layer link between a controller and remote nodes, with RS-422 providing balanced point-to-point signaling and RS-485 supporting multipoint buses.
Key features include TIA/EIA RS-485 and RS-422 compliance, a maximum data rate of 12 Mbps, ±15 kV ESD protection, and operation on a single 3.3 V supply. The half-duplex configuration shares the driver and receiver bus connections, reducing board area and external switching requirements. A fail-safe receiver is designed to provide a defined output when the bus is open-circuit, while the low-power shutdown function supports systems that need to reduce consumption when the interface is inactive.
The ADM3485E family combines a low-power 3.3 V architecture with high-speed differential signaling. Its 12 Mbps capability suits short-distance, high-speed industrial links, while multipoint operation accommodates systems with as many as 32 nodes. The 8-pin SOIC package supports conventional surface-mount assembly, and the same compact footprint simplifies comparison with other 8-pin half-duplex line transceivers.
Typical uses include industrial control networks, factory automation equipment, instrumentation, motor-control subsystems, and embedded serial buses. The device can also serve as a robust physical-layer interface between a host controller and remotely located sensors, actuators, or data-acquisition modules where 3.3 V logic levels and multidrop capability are required.
Designers should preserve the transceiver's common-mode range and termination requirements when laying out the bus. Place the differential line pair with continuous ground reference, route the pair as a coupled transmission-line structure, and position termination only at designated bus endpoints. Add suitable surge protection and verify that system grounding and cable length remain compatible with the operating data rate.
This page combines electrical characteristics, package details, application guidance, parameter comparisons, and verified drop-in alternatives. It also highlights design trade-offs involving data rate, bus direction control, ESD protection, termination, and multipoint operation so engineers can select the correct interface IC before layout begins.
Bộ thay thế dễ dàng lắp đặt cho ADM3485EAR — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với ADM3485EAR (cùng hình factor và footprint) — khác nhau ở Package, Bus Configuration, Low-Power Operation, Duplex Mode, Data Rate.
ADM3485EARZ
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →ADM3483EARZ
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
ADM3491EARZ
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →ST3485ECDR
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
SP3485EN-L
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →ADM3485EAR Thông số kỹ thuật
| Điện áp cung cấp | 3.3 V |
| Tốc độ dữ liệu | 12 Mbps |
| ESD Protection | ±15 kV |
| Protocol Support | TIA/EIA RS-485 and RS-422 |
| Duplex Mode | Half-duplex |
| Driver Count | 1 driver |
| Receiver Count | 1 receiver |
| Maximum Bus Nodes | 32 nodes |
| Receiver Fail-Safe Behavior | Open-circuit fail-safe design |
| Low-Power Shutdown | Supported |
| Bus Configuration | Multipoint differential bus |
| Hộp | 8-pin SOIC |
| Kiểu lắp đặt | Surface mount |
Hướng dẫn cấu hình chân ADM3485EAR 8-pin soic
Cấu hình chân cho ADM3485EAR (8-pin soic gói). Số thứ tự chân, chức năng và sơ đồ kết nối được xác định trong tài liệu thông số kỹ thuật của nhà sản xuất. Tham khảo nó để biết footprint và hướng dẫn hàn chính xác.
Không có dữ liệu chân cụ thể sẵn có cho ADM3485EAR.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
ADM3485EAR phù hợp cho 6 Áp dụngs: Industrial Automation Bus Interface, Data Acquisition and Instrumentation, Motor and actuator Control Networks, Building Access and Security Equipment, Embedded Sensor and Actuator Networks, Test and Measurement Equipment.
Industrial Automation Bus Interface
The ADM3485EAR fits factory automation links that need balanced differential signaling from a 3.3 V controller. Place the transceiver between the host UART and a multidrop RS-485 bus, using its integrated half-duplex driver and receiver to support a data rate of up to 12 Mbps. The ±15 kV ESD protection improves resilience at connector-exposed equipment interfaces, while the fail-safe open-circuit receiver behavior helps establish a defined logic state on an idle or broken bus.
Được đề xuất
Data Acquisition and Instrumentation
The ADM3485EAR provides a compact physical-layer interface between instrumentation controllers and remotely located measurement modules. Its 3.3 V supply operation suits modern mixed-signal systems, and the 12 Mbps rate allows short, high-speed links carrying command, configuration, and measurement traffic. Balanced differential signaling reduces susceptibility to common-mode noise present near motors, relays, and switching power converters. The 8-pin SOIC footprint also keeps the interface compact beside an ADC or microcontroller.
Được đề xuất
Motor and actuator Control Networks
The ADM3485EAR is suitable for communication links between a controller and motor-drive or actuator modules installed away from the main board. Its half-duplex architecture uses one bidirectional differential pair, reducing wiring in multipoint networks, while the receiver's fail-safe design helps manage open-circuit conditions. The 12 Mbps capability supports high-rate command traffic over appropriately short cables, and ±15 kV ESD protection adds useful robustness where cables connect through industrial connectors.
Được đề xuất
Building Access and Security Equipment
The ADM3485EAR can connect access-control panels, card readers, and distributed security modules over a 3.3 V RS-485 network. Differential signaling supports reliable communication where cable runs pass near elevators, lighting equipment, or other electrically noisy systems. The multipoint capability permits as many as 32 nodes, and the low-power shutdown function helps conserve energy in intermittently used peripheral devices. System designers should maintain a continuous ground reference and use endpoint termination.
Được đề xuất
Embedded Sensor and Actuator Networks
The ADM3485EAR provides a practical interface for embedded controllers communicating with distributed sensors and actuators over a short cable. Its 3.3 V operation minimizes level-shifting requirements when paired with modern microcontrollers, while one driver and one receiver support a compact half-duplex topology. At rates up to 12 Mbps, the device can support responsive command and status traffic, subject to distance, cable attenuation, node loading, and termination constraints.
Được đề xuất
Test and Measurement Equipment
The ADM3485EAR is appropriate for laboratory and production-test equipment that communicates with remote fixtures or instrument modules. Its balanced differential interface helps maintain data integrity across cable connections that may share space with switching supplies and digital clocks. The 8-pin SOIC package simplifies compact instrument designs, while half-duplex control supports shared two-wire buses. For high-throughput test systems, use controlled impedance and endpoint termination to preserve the advertised 12 Mbps capability.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho ADM3485EAR — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | ADM3485EARZ | ADM3483EARZ | ADM3491EARZ | ST3485ECDR | SP3485EN-L |
|---|---|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | STMicroelectronics | Exar |
| Package | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC |
| Supply Voltage | 3.3 V | 3.3 V | 3.3 V | 3.3 V | 3.3 V | 3.3 V |
| Protocols | RS-485 and RS-422 | RS-485 and RS-422 | RS-485 and RS-422 | RS-485 and RS-422 | RS-485 and RS-422 | RS-485 and RS-422 |
Bảo phân biệt quan trọng
- High-speed 3.3 V operation (vsSP3485EN-L)
- Clearly documented ESD protection (vsST3485ECDR)
- Multipoint fail-safe receiver design (vsADM3491EARZ)
- Direct same-brand ordering alternative (vsADM3485EARZ)
Ghi chú thiết kế
Route the RS-485 and RS-422 differential pair as a controlled-impedance transmission line with continuous ground reference. Keep the driver and receiver connections away from switching-node traces and maintain consistent spacing between the pair. Place bypass capacitance close to the 3.3 V and ground pins, and keep the connector-side protection and termination components close to the entry point where transient energy first enters the board.
Do not enable the driver while the receiver remains active on the same bus unless the transceiver datasheet explicitly permits that state. A half-duplex RS-485 node commonly needs coordinated driver-enable and receiver-enable control so the driver does not contend with another transmitter. Validate the enable polarity, startup sequence, and bus idle condition in firmware before releasing the transceiver onto the network.
Terminate the differential bus only at the two physical endpoints, using the termination resistance specified by the Analog Devices ADM3485E datasheet and the impedance of the installed cable. Avoid placing termination across every node in a multidrop network. For long or high-speed links, calculate attenuation and reflection behavior, maintain a ground reference along the cable route, and consider fail-safe biasing only after confirming its effect on the complete network.
The 12 Mbps rating is not a guarantee that every cable length or topology supports that rate. Use shorter, properly terminated cables at the highest data rates, keep stub lengths short, and verify signal integrity with an oscilloscope in the installed enclosure. Also check the UART baud-rate tolerance and ensure that the host controller provides enough turnaround delay for the half-duplex bus.
Thông tin tuân thủ
The ADM3485E is an industrial interface IC and is not presented as an AEC-Q100-qualified automotive device. Specific RoHS, REACH, lead-free, halogen-free, and conflict-minerals statements require confirmation for the exact ADM3485EAR ordering code.