ADM3485EAR - 12 Mbps 3.3 V RS-485 Transceiver | Analog Devices
MPN: ADM3485EAR ✓ AktifADM3485EAR Genel Bakış
An RS-485 transceiver is an interface IC that converts logic-level serial data into balanced differential signals for reliable communication over longer cables and noisy environments. The corresponding receiver converts differential bus voltage back into a logic-level signal. Together, these devices form the physical-layer link between a controller and remote nodes, with RS-422 providing balanced point-to-point signaling and RS-485 supporting multipoint buses.
Key features include TIA/EIA RS-485 and RS-422 compliance, a maximum data rate of 12 Mbps, ±15 kV ESD protection, and operation on a single 3.3 V supply. The half-duplex configuration shares the driver and receiver bus connections, reducing board area and external switching requirements. A fail-safe receiver is designed to provide a defined output when the bus is open-circuit, while the low-power shutdown function supports systems that need to reduce consumption when the interface is inactive.
The ADM3485E family combines a low-power 3.3 V architecture with high-speed differential signaling. Its 12 Mbps capability suits short-distance, high-speed industrial links, while multipoint operation accommodates systems with as many as 32 nodes. The 8-pin SOIC package supports conventional surface-mount assembly, and the same compact footprint simplifies comparison with other 8-pin half-duplex line transceivers.
Typical uses include industrial control networks, factory automation equipment, instrumentation, motor-control subsystems, and embedded serial buses. The device can also serve as a robust physical-layer interface between a host controller and remotely located sensors, actuators, or data-acquisition modules where 3.3 V logic levels and multidrop capability are required.
Designers should preserve the transceiver's common-mode range and termination requirements when laying out the bus. Place the differential line pair with continuous ground reference, route the pair as a coupled transmission-line structure, and position termination only at designated bus endpoints. Add suitable surge protection and verify that system grounding and cable length remain compatible with the operating data rate.
This page combines electrical characteristics, package details, application guidance, parameter comparisons, and verified drop-in alternatives. It also highlights design trade-offs involving data rate, bus direction control, ESD protection, termination, and multipoint operation so engineers can select the correct interface IC before layout begins.
Drop-in alternatifler için ADM3485EAR — aynı paket, pin-başına uyumlu. PCB yeniden montajı gerektiren farklı paket bileşenleri dışlanmıştır.
Bu Serideki Variantlar
Yedek parça uyumlu olan aynı serideki modeller ADM3485EAR (aynı form faktörü ve ayağa oturma) — farklı olan Package, Bus Configuration, Low-Power Operation, Duplex Mode, Data Rate.
ADM3485EARZ
✅ YerleştirmeFiyat için iletişime geçin
Veri Şablonunu Görüntüle →ADM3483EARZ
✅ Yerleştirme📋 Katalogda Olmayan Referans Alternatifi
ADM3491EARZ
✅ YerleştirmeFiyat için iletişime geçin
Veri Şablonunu Görüntüle →ST3485ECDR
✅ Yerleştirme📋 Katalogda Olmayan Referans Alternatifi
SP3485EN-L
✅ YerleştirmeFiyat için iletişime geçin
Veri Şablonunu Görüntüle →ADM3485EAR Özellikler
| Besleme Gerilimi | 3.3 V |
| Veri Hızı | 12 Mbps |
| ESD Protection | ±15 kV |
| Protocol Support | TIA/EIA RS-485 and RS-422 |
| Duplex Mode | Half-duplex |
| Driver Count | 1 driver |
| Receiver Count | 1 receiver |
| Maximum Bus Nodes | 32 nodes |
| Receiver Fail-Safe Behavior | Open-circuit fail-safe design |
| Low-Power Shutdown | Supported |
| Bus Configuration | Multipoint differential bus |
| Paket | 8-pin SOIC |
| Montaj Türü | Surface mount |
ADM3485EAR 8-pin soic Pin Yapısı Kılavuzu
ADM3485EAR (8-pin soic paket) için pin yapısı. Pin numaralandırma, işlevleri ve bağlantı şemaları üretici veri kitapçığında tanımlanmıştır. Doğru ayak ve soldurma kılavuzları için onu referans alın.
Ayrıntılı pin çıkış verisi mevcut değil: ADM3485EAR.
Aşağıdaki veri sayfası tam pin konfigürasyonu için.
Tipik Uygulamalar
ADM3485EAR için uygundur 6 uygulamas: Industrial Automation Bus Interface, Data Acquisition and Instrumentation, Motor and actuator Control Networks, Building Access and Security Equipment, Embedded Sensor and Actuator Networks, Test and Measurement Equipment.
Industrial Automation Bus Interface
The ADM3485EAR fits factory automation links that need balanced differential signaling from a 3.3 V controller. Place the transceiver between the host UART and a multidrop RS-485 bus, using its integrated half-duplex driver and receiver to support a data rate of up to 12 Mbps. The ±15 kV ESD protection improves resilience at connector-exposed equipment interfaces, while the fail-safe open-circuit receiver behavior helps establish a defined logic state on an idle or broken bus.
Önerilen
Data Acquisition and Instrumentation
The ADM3485EAR provides a compact physical-layer interface between instrumentation controllers and remotely located measurement modules. Its 3.3 V supply operation suits modern mixed-signal systems, and the 12 Mbps rate allows short, high-speed links carrying command, configuration, and measurement traffic. Balanced differential signaling reduces susceptibility to common-mode noise present near motors, relays, and switching power converters. The 8-pin SOIC footprint also keeps the interface compact beside an ADC or microcontroller.
Önerilen
Motor and actuator Control Networks
The ADM3485EAR is suitable for communication links between a controller and motor-drive or actuator modules installed away from the main board. Its half-duplex architecture uses one bidirectional differential pair, reducing wiring in multipoint networks, while the receiver's fail-safe design helps manage open-circuit conditions. The 12 Mbps capability supports high-rate command traffic over appropriately short cables, and ±15 kV ESD protection adds useful robustness where cables connect through industrial connectors.
Önerilen
Building Access and Security Equipment
The ADM3485EAR can connect access-control panels, card readers, and distributed security modules over a 3.3 V RS-485 network. Differential signaling supports reliable communication where cable runs pass near elevators, lighting equipment, or other electrically noisy systems. The multipoint capability permits as many as 32 nodes, and the low-power shutdown function helps conserve energy in intermittently used peripheral devices. System designers should maintain a continuous ground reference and use endpoint termination.
Önerilen
Embedded Sensor and Actuator Networks
The ADM3485EAR provides a practical interface for embedded controllers communicating with distributed sensors and actuators over a short cable. Its 3.3 V operation minimizes level-shifting requirements when paired with modern microcontrollers, while one driver and one receiver support a compact half-duplex topology. At rates up to 12 Mbps, the device can support responsive command and status traffic, subject to distance, cable attenuation, node loading, and termination constraints.
Önerilen
Test and Measurement Equipment
The ADM3485EAR is appropriate for laboratory and production-test equipment that communicates with remote fixtures or instrument modules. Its balanced differential interface helps maintain data integrity across cable connections that may share space with switching supplies and digital clocks. The 8-pin SOIC package simplifies compact instrument designs, while half-duplex control supports shared two-wire buses. For high-throughput test systems, use controlled impedance and endpoint termination to preserve the advertised 12 Mbps capability.
Önerilen
Önerilen Ürünler Özeti
Mühendislik referans verileri: ADM3485EAR — karşılaştırma, tasarım rehberi ve uyumluluk bilgileri.
Seçim Kılavuzu
Alternatiflerle Karşılaştırma
| Parametre | Bu Ürün | ADM3485EARZ | ADM3483EARZ | ADM3491EARZ | ST3485ECDR | SP3485EN-L |
|---|---|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | STMicroelectronics | Exar |
| Package | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC |
| Supply Voltage | 3.3 V | 3.3 V | 3.3 V | 3.3 V | 3.3 V | 3.3 V |
| Protocols | RS-485 and RS-422 | RS-485 and RS-422 | RS-485 and RS-422 | RS-485 and RS-422 | RS-485 and RS-422 | RS-485 and RS-422 |
Ana Farklılayıcılar
- High-speed 3.3 V operation (karşılaştırma:SP3485EN-L)
- Clearly documented ESD protection (karşılaştırma:ST3485ECDR)
- Multipoint fail-safe receiver design (karşılaştırma:ADM3491EARZ)
- Direct same-brand ordering alternative (karşılaştırma:ADM3485EARZ)
Tasarım Notları
Route the RS-485 and RS-422 differential pair as a controlled-impedance transmission line with continuous ground reference. Keep the driver and receiver connections away from switching-node traces and maintain consistent spacing between the pair. Place bypass capacitance close to the 3.3 V and ground pins, and keep the connector-side protection and termination components close to the entry point where transient energy first enters the board.
Do not enable the driver while the receiver remains active on the same bus unless the transceiver datasheet explicitly permits that state. A half-duplex RS-485 node commonly needs coordinated driver-enable and receiver-enable control so the driver does not contend with another transmitter. Validate the enable polarity, startup sequence, and bus idle condition in firmware before releasing the transceiver onto the network.
Terminate the differential bus only at the two physical endpoints, using the termination resistance specified by the Analog Devices ADM3485E datasheet and the impedance of the installed cable. Avoid placing termination across every node in a multidrop network. For long or high-speed links, calculate attenuation and reflection behavior, maintain a ground reference along the cable route, and consider fail-safe biasing only after confirming its effect on the complete network.
The 12 Mbps rating is not a guarantee that every cable length or topology supports that rate. Use shorter, properly terminated cables at the highest data rates, keep stub lengths short, and verify signal integrity with an oscilloscope in the installed enclosure. Also check the UART baud-rate tolerance and ensure that the host controller provides enough turnaround delay for the half-duplex bus.
Uyumluluk Bilgisi
The ADM3485E is an industrial interface IC and is not presented as an AEC-Q100-qualified automotive device. Specific RoHS, REACH, lead-free, halogen-free, and conflict-minerals statements require confirmation for the exact ADM3485EAR ordering code.